Soundking FP208 Professional Speaker System User Manual

Soundking FP208 Professional Speaker System

Product Information

The product is a mixer with multiple inputs and outputs. It has 2 microphone balanced inputs, 2 stereo line inputs, 2 effects return inputs, 2 effects send outputs, 1 monitor output, 1 tape input, and 2 main outputs. The mixer has low-cut and high-cut filters, mid-range equalization, and digital effects. It also has a voltage selector for different voltages and a fan for cooling. The mixer can be used in both bridged and floating modes.

Product Usage Instructions

To use the mixer, connect your audio sources to the appropriate inputs. Microphones should be connected to either of the two microphone-balanced inputs. Stereo line sources should be connected to the stereo line inputs. Effects pedals or processors should be connected to the effects return inputs and outputs. Monitors or amplifiers should be connected to the monitor output or main outputs. Tape players or recorders should be connected to the tape input and tape output.
Adjust the low-cut and high-cut filters using the appropriate knobs to remove unwanted frequencies from the audio signal. Use the mid-range equalization to adjust the level of frequencies in the mid-range. Adjust the digital effects using the appropriate knobs and switches to add reverb, delay, chorus, or other effects to your audio signal.
Use the main output or tape output to connect to your recording device or amplifier. The peak volume indicator will show if your signal is too loud or too soft. Adjust the volume using the appropriate knobs for each input source.
When finished using the mixer, turn off all input sources and disconnect all cables. Store the mixer in a cool and dry place to prevent damage.

**Active Speaker System

**

WIRING

TECHNICAL SPECIFICATIONS

Passive Speaker System

IMPORTANT SAFETY SYMBOLS

• The symbol is used to indicate that some hazardous live terminals are involved within this apparatus, even under the normal operating conditions, which may be sufficient to constitute the risk of electric shock or death.
• The symbol is used in the service documentation to indicate that specific component shall be replaced only by the component specified in that documentation for safety reasons.
• Protective grounding terminal
• Alternating current/voltage
• Hazardous live terminal
• ON : Denotes the apparatus is turned on
• OFF : Denotes the apparatus is turned off.
• WARNING : Describes precautions that should be observed to prevent the danger of injury or death to the operator.
• CAUTION : Describes precautions that should be observed to prevent danger of the apparatus.

IMPORTANT SAFETY INSTRUCTIONS

• Read these instructions.
• Keep these instructions.
• Heed all warning.
• Follow all instructions.

Water & Moisture
The apparatus should be protected from moisture and rain, can not use near water, for example: near a bathtub, kitchen sink or swimming pool, etc.

Heat
The apparatus should be located away from the heat source such as radiators, stoves or other appliances that produce heat.

Ventilation

• Do not block areas of ventilation opening. Failure to do could result in fire. Always install in accordance with the manufacturer’s instructions.
  • Object and Liquid Entry
• Objects do not fall into and liquids are not spilled into the inside of the apparatus for safety.

Power Cord and Plug

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong Is provided for your safety. If the provided plug does not fit into your outlet, refer to an electrician for replacement.

Power Supply

• The apparatus should be connected to the power supply only of the type as marked on the apparatus or described in the manual. Failure to do could result in damage to the product and possibly the user.
• Unplug this apparatus during lightning storms or when unused for long periods of time.

Fuse
To prevent the risk of fire and damaging the unit, please use only of the recommended fuse type as described in the manual. Before replacing the fuse, make sure the unit turned off and disconnected from the AC outlet.

Electrical Connection
Improper electrical wiring may invalidate the product warranty.

Cleaning
Clean only with a dry cloth. Do not use any solvents such as benzol or alcohol.

Servicing

• Do not implement any servicing other than those means described in the manual. Refer all servicing to qualified service personnel only.
• Only use accessories/attachments or parts recommended by the manufacturer.

Warning
Please remember the high sound pressure do not only temporarily damage your sense of hearing, but can also cause permanent damage. Be careful to select a suitable volume.

INTRODUCTION

The series professional speaker system is divided active speaker and passive speaker, it consists of seven sizes, each sizes includes several models, following list will show you the details.

Passive speaker system

Active speaker system

PASSIVE SPEAKER SYSTEM

Features

• Enclosure adopted a high-impact polymer, injection molded shaping. It has high intensity and light weight, set a handle, easy to carry it. Designed a non-symmetrical enclosure outline. It can be used as a fold-back speaker.
• Woofer speakers make a high-powered pro-speaker. It has a wide range, low distortion, high sensitivity, and adopted an aluminum frame. It has non-mechanical resonance.
• Driver selected a titanium diaphragm, and light mass voice coil, making it high frequency reached 18,000Hz.
• Crossover adopted a high-quality polypropylene condenser, flame proof resistor, and low inductance. Precision design dividing frequency and smooth frequency response, and designed auto-limit protection circuit to avoid damage to driver.

Control Element

Binding post/1/4″ TRS jack/Speakon INPUT connectors, serve to receive the powered signal coming from an external power amplifier. If necessary, some of these can be regarded a link output connector

Connection Examples

Connection Examples

ACTIVE SPEAKER SYSTEM

Features

• Enclosure adopted a high-impact polymer, injection molded shaping. It has high intensity and is lightweight, set a handle, easy to carry it. Designed a non-symmetrical enclosure outline. It can be used as a fold-back speaker.
• Woofer speakers make a high powered per speaker. It has a wide-range, low distortion, high sensitivity, and adopted an aluminum frame. It has non-mechanical resonance.
• Driver selected a titanium diaphragm, and light mass voice coil, make it high frequency reached 18,000Hz.
• The new A.A.S.S (Automatic amplitude servo system) processor ensures total protection of the transducers and improvement of the acoustic response.

Control Element

1. IN link OUT
   Input and output sockets are electronically balanced. The “IN” XLR socket allows connection of a dynamic microphone at low impedance or of a pre- amplified signal such as a mixer line out; the “OUT” socket is connected in parallel (link) with the input “IN” allowing multiple connections of more systems with the same signal

2. LINE/MIC
   Switch to select either “MIC” position if a microphone or a low-level appliance is connected; the “LINE” position allows connection of high-level signal sources

3. GAIN
   Regulates pre-amplification of the signal coming from the input IN, ensuring perfect operation of the channel circuits. For a well-balanced again adjustment, set the Volume to approx 3 4 clockwise, then adjust the gain accordingly.

4. HIGH/MID/LOW
   3-band equalization to modify the sound tone. These controls are electronically post-gain and if boosted can clip the channel, in this case adjust the gain control anticlockwise. When the potentiometers are set to 0 the tone remains unchanged.

5. VOL
   Volume potentiometer to control the channel signal level. Normally optimal channel circuit performance is achieved with the knob positioned at approx. 3/4 clockwise and the gain control set to the desired level.

6. GND/LIFT
   2-position selector for separating the signal source ground and the amplifier ground circuits.
   ON : the signal ground is electrically disconnected from the amplifier ground circuit(the chassis). If a hum is heard in the loudspeakers, the ON position breaks the ground loop, often the cause of this interference.
   OFF: the ground of the input signals is electrically connected to the amplifier ground circuit (the chassis). USE GROUND LIFT ONLY WITH BALANCED SIGNALS.

7. A.A.S.S
   Processor circuit which protects the transducers from excessive tensions; when the audio signal reaches the dangerous threshold for the transducers, the A.A.S.S system automatically intervenes by reducing the amount of signal within acceptable limits: the time reaction of the system are very fast.
   The speaker system features two separate protection systems, both for the low- frequency and the high-frequency drivers; the activation of these protections is recognizable via the “HF” and “LF” leds lighting up in the control panel.

8. PWR
   LED signal to indicate the switching on of the system.

9. TONE
   This control allows you to adjust the tone within 0 ~ 10.

10. HP FILTERED OUT
    An electronically balanced XLR connector serves to output the high-frequency signal.

11. POWER switch
    Turns this apparatus on or off.

12. FUSE holder
    The fuse holder is for containing the fuse, which is a safety device that protects the AC supplies circuit of the unit.
    Caution : if the fuse blew out, it should be replaced with the same type and specification, if the fuse continues to blow out, please stop using and refer servicing to qualified personnel.

13. AC power socket
    It is used to connect the power supply to the unit via an enclosed power cord.
    Caution : ensure the source voltage matches the voltage of the product before turning on the unit

14. Voltage selection switch
    This switch provides two voltage selections: 115V or 230V, please select the proper voltage depending on the actual application

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>