Soundking KT12MA-1 Professional Speaker System User Manual
- June 10, 2024
- Soundking
Table of Contents
USER’S MANUAL
Professional Speaker System
ECNJG1905217
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
In order to avoid the possibility of physical injury to you or others, or
damage to the device or other property, please follow the basic precautions
listed below. These precautions include, but are not limited to, the
following:
- Read and keep these instructions
- Heed all warning.
- Follow all instructions.
- This device is capable of delivering high sound pressure levels beyond 120dB, which may cause permanent hearing damage. Please pay more attention to select a proper volume.
- Do not remove the front metal grille which protects the loudspeaker (or the inside components) from any irreparable damage. The device contains no user-serviceable parts.
- Do not use solvents such as acetone or alcohol to clean the device, or the solvent may damage its finish.
- Do not expose the device to the atrocious environment for a long time (for example: moisture, excessive heat, strong temperature variations, etc.)
- Clean the device once in a while to avoid excessive dust; when removing the device, please pack the device with original packaging for any transport purpose
- Only use the accessories/attachments or parts recommended by the manufacturer.
CAUTION:
In order to avoid the possibility of damage to the device or other property,
please follow the basic precautions listed below. These precautions include,
but are not limited to, the following:
Location
The series speaker features with smart and convenient installation facility,
which can be located on a stable ground surface or mounted on a stand (only
for full-range speaker) or other ways. For protecting your speaker from
possible damage, please note following caution:
- If you place your speaker on flat surface, please make sure the flat surface is even, completely firm.
- Before moving the speakers, remove all connected cables.
- When installing or transporting the device, always use two or more people.
Connections
- Always make sure that all devices are turned off when connecting the speaker to other devices. Also make sure that all volume and level controls are turned down to minimum before turning the power on.
- Use only speaker cable for connecting speakers to speaker jacks. Use of other types of cables may result in fire.
INTRODUCTION
Based on many years of R&D experience accumulation, Sounding specially designs
the stage monitoring speaker cabinet series, active and passive, 45° or 20°
for selection. This series of speaker cabinets are suitable for stage show and
near field reinforcement.
Features:
- LF/HF units use the same magnetic and coaxial Nd magnetic design to improve the voice coil efficiency & sensitivity, and to ensure the reproduction of the original sound and to lower various distortions.
- Ti/PK compound diaphragm of HF compression driver and 75mm voice coil ensure transparent tone.
- The active amplifier adopts HF/LF dual amp design to ensure sufficient headroom. Class D amplifier enlarges the dynamic range and ensure the pure tone. The amplifier is also designed with perfect protection: thermal/power surge/over-load/short circuit protection.
- The passive cabinet adopts LC crossover and HF PTC protection. The refined components offer original sound.
- Unique and compact contour; triangle handle for convenient transportation.
- 45° and 20° monitoring angles;
- Waterproof environmental friendly paint and steel grille.
PANEL OPERATION
-
Passive speaker cabinet
KT12M -
Signal input connector ( INPUT)
The professional speaker connector to connect the signal from external amplifier from +1, -1. -
Link connector (LINK) The LINK connector is used to link multiple speaker cabinets.
-
Active monitoring speaker cabinet
Specification
Model | KT12M |
---|---|
Type | two way passive monitoring speaker cabinet |
Frequency response (-10dB) | 55Hz–20KHz |
Impedance ( 0 ) | 8Ω |
Sensitivity ( 1W@1m ) | 96dB |
Mas SPL(dB) | 127dB |
Rated power ( RMS ) | 300W (continuous), 1200W (peak) |
coaxial speaker LF unit | 12″ LF/75mm voice coil/Nd mag/300W |
HF unit | 75mm compression driver/1.5 inch throat/Nd mag/100W |
Coverage (V*H) | 80° *80° |
Crossover | 1.2kHz |
Input connector | 4xSPOKEN |
Dimension(WHD) | 468430442 (mm) |
Weight | 17.5 kg |
Model | KT12M-1 |
--- | --- |
Type | two way passive monitoring speaker cabinet |
Frequency response (-10dB) | 55Hz–20KHz |
Impedance ( Q ) | 8Ω |
Sensitivity ( 1W@1m ) | 96dB |
Mas SPL(dB) | 127dB |
Rated power ( RMS ) | 300W (continuous), 1200W (peak) |
coaxial speaker LF unit | 12″ LF/75mm voice coil/Nd mag/300W |
HF unit | 44mm compression driver/1 inch throat/Nd mag/40W |
Coverage ( V*H ) | 80° *80° |
Crossover | 2.2kHz |
Input connector | 4xSPOKEN |
Dimension(WHD) | 462430442 (mm) |
Weight | 15 kg |
Model | KT15M |
--- | --- |
Type | two way passive monitoring loudspeaker |
Frequency response (-10dB) | 55Hz–20kHz |
Impedance ( 0 ) | 8Ω |
Sensitivity ( 1W@lm ) | 97dB |
Mas SPL(dB) | 129B |
Rated power ( RMS) | 400W(continue), 1600W(peak) |
coaxial speaker LF unit | 15″LF/75mm voice coil/400W/80 |
HF unit | 44 compression driver/1″ throat/IOW/80 |
Coverage (V*H ) | 80° *80° |
Crossover | 2.2kHz |
Input connector | 4xSPOKEN |
Dimension(WHD) | 500x500x501 (mm) |
Weight | 20.5 kg |
Model | KT12MA |
--- | --- |
Type | two way active monitoring speaker cabinet |
Frequency response (-10dB) | 55Hz–20KHz |
Sensitivity ( 1W@1m ) | 0dBu |
Mas SPL(dB) | 124dB |
Amp power (RMS) | 400W (LF)+100W (HF) |
coaxial speaker LF unit | 12″ LF/75mm voice coil/Nd mag/300W |
HF unit | 75mm compression driver/1.5 inch throat/Nd mag/100W |
Coverage (V*H ) | 80° * 80° |
Crossover | 1.1kHz |
Input connector | JACK/XLR |
Input voltage | 230V/115V (for option) |
Dimension(WHD) | 468430442 (mm) |
Weight | 18.5 kg |
Model | KT12MA-1 |
---|---|
Type | two way active monitoring loudspeaker |
Frequency response (-10dB) | 55Hz–20kHz |
Sensitivity ( 1W@1m ) | 0dBu |
Mas SPL(dB) | 124dB |
Amp power (RMS) | 400W (LF)+70W (HF) |
coaxial speaker LF unit | 12″ LF/75mm voice coil/300W/80 |
HF unit | 44 compression driver/1″ throat/40W/80 |
Coverage (V*H ) | 80° * 80° |
Crossover | 2.2kHz |
Input connector | JACK/XLR |
Input voltage | 230V/115V (for option) |
Dimension(WHD) | 462430442 (mm) |
Weight | 16 kg |
Model | KT15MA |
--- | --- |
Type | two way active monitoring loudspeaker |
Frequency response (-10dB) | 55Hz–20kHz |
Sensitivity ( 1W@1m ) | 0dBu |
Mas SPL(dB) | 129dB |
Amp power (RMS) | 400W (LF)+100W (HF) |
coaxial speaker LF unit | 15″ LF/75mm voice coil/400W/84 |
HF unit | 44 compression driver/1″ throat/40W/80 |
Coverage (V*H) | 80° * 800 |
Crossover | 2.2kHz |
Input connector | JACK/XLR |
Input voltage | 230V/115V (for option) |
Dimension(WHD) | 500x500x501 (mm) |
Weight | 23 kg |
Maintenance
Problem | Analyze |
---|---|
No Sound | Check if system cables, power supply and other devices operate? |
Distortion | Check if signal is overloaded, amp is clipping, switch reasonable? |
Abnormal tone | Check if signal wire is connected correctly and tone switch |
reasonable?
Loud Noise| Check if signal wire is connected correctly, and ground switch
connected correctly?
Burn-in| Chec if the voltage of transforming switch is selected correctly?
Note: if the problem is still there checking mentioned above, please contact our dealer or our customer service department. We are happy to help you and solve the problem.
SOUNDKING AUDIO
WWW.SOUNDKING.COM
All rights reserved to SOUNDKING. No part of this manual may be reproduced,
translated or
photocopied by any means for any purpose, without the written permission of
SOUNDKING.
The information involved in this manual is subject to change without
notice.
Documents / Resources
|
Soundking KT12MA-1 Professional Speaker
System
[pdf] User Manual
KT12MA, KT12M-12MA, KT12MA-1, KT12MA-1 Professional Speaker System,
Professional Speaker System, Speaker System
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>