FLINQ FQC8262 10W Solar LED Floodlight Instruction Manual

FQC8262 10W Solar LED Floodlight

Product Information

The FlinQ Solar LED Floodlight 10W is a solar-powered lamp that is suitable for use in gardens, courtyards, parking lots, squares, villas, garages, pathways, entrances, and other outdoor areas. It has a built-in Li-ion battery and a solar panel that charges during the day to provide lighting at night. The lamp has two working modes – Sensor Mode and Constant Lighting Mode – and is equipped with an internal battery pack that can be replaced if necessary.

• Product Name: FlinQ Solar LED Floodlight 10W
• Product Code: FQC8262
• Power/Lumen: 10W
• LEDs: Multiple
• Li-ion Battery: Built-in
• Solar Panel: Built-in
• Bracket: Included
• IP Degree: Waterproof
• Beam Angle: Multiple
• Detection Angle/Distance: 8mtrs
• Charging Time: Depends on sunshine duration & weather & work mode
• Working Time: Depends on sunshine duration & weather & work mode
• Dimension: Not specified
• Installation Height: Recommended height of 2-4 meters
• Warranty: 1 year extra warranty (2+1)

Product Usage Instructions

• Step 1: Install the lamp in a location where it can get enough sunshine. Use the included accessories and tools to prepare the lamp and mount it on the wall or put it on a flat surface.

• Step 2: Adjust the light and bracket angle as needed using the
  Allen wrench and screw. The recommended installation height is 2-4 meters.

• Step 3: Choose the working mode by pressing the on/off button.
  The lamp will automatically turn on to Sensor Mode when the button is pressed once, and Constant Lighting Mode when the button is pressed for 3 seconds and the lamp shines one time.

• Step 4: In Sensor Mode, the lamp will automatically light up at night and turn to full brightness when motion is detected in the range of 8mtrs. It will then dim to lower brightness after 20 seconds of no motion. In Constant Lighting Mode, the lamp will stay on at full brightness until the battery capacity reduces to zero and the lamp switches back to Sensor Mode.

• Step 5: Please note that the lighting time depends on sunshine duration, weather, and work mode. The lamp is equipped with an internal battery pack that is replaceable if necessary. If the battery is taken out and put back in or replaced with new ones, please turn the solar panel towards sunshine or a strong light to activate the lamp.

• Step 6: Please do not dispose of the battery with household garbage to avoid explosion. Non-professionals should not disassemble the lamp.

For additional support, a digital warranty certificate and manual can be found by scanning the QR code or visiting flinqproducts.nl/registration. For any battery replacement needs, please contact the seller for the correct new battery pack.

Welcome to the FlinQ family
Thanks for purchasing one of our items! To ensure continuous operation and accuracy, please read these operating instructions carefully before use and save this manual for future use. Passing certain procedures may result in incorrect reading and incorrect use of this product. We hope that you will enjoy using your new FlinQ-product! If by any chance the item is damaged, defective or broken, you are covered with warranty! Please do not hesitate to contact us for any questions, concerns or suggestions at the email address as mentioned in this manual.

Register your FlinQ product
We can imagine you want to treat your FlinQ item carefully.
Register your product and you will be entitled to the following:

1. 1 year extra warranty (2+1)
2. Personal support
3. Digital warranty certificate
4. Digital manual

Scan the QR code or go to flinqproducts.nl/registration

Specifications

card)

Working Modes

• Press the on / off button, lamp will automatically turn on to Sensor Mode.
• Keep pressing the on / off button for 3 seconds and shining one time, lamp turns to constant lighting mode.

Sensor mode

1. Battery above 30%
   Automatically lights up at night and turns to full brightness when motion is detected in the range of ≤8mtrs. After that, it will dim to lower brightness after 20 seconds of no motion.

2. Battery below 30%
   Automatically lights up at night and turns to full brightness when motion is detected in the range of ≤8mtrs. The lamp then turns off after 20 seconds of no motion.

Constant lighting mode

1. Constant lighting mode
   Press the button for 3 seconds and the light will shine one time. Now the lamp turns to Keep Lighting Mode, both motion and light sensors are disabled. Permanently keep lighting until the battery capacity reduces to zero and the switching back to Sensor Mode.

Applications
You can easily install it for garden, courtyard, parking lot, square, villa, garage, pathway, entrance etc.

Notices

1. This is a solar powered lamp, please install it in a location where can get enough sunshine.
2. Please note the lighting time depends on sunshine duration & weather & work mode.
3. The lamp will light up automatically at dusk in Sensor Mode.
4. Built-in intelligent IC is with over-charge, over-discharge and over-voltage protection.
5. The lamp is equipped with an internal battery pack, which is replaceable. If any need, please contact seller for correct new battery pack.
6. If the battery is taken out and put back in or replaced with new ones, please toward the solar panel to sunshine or a strong light to activate the lamp.
7. Non-professionals please do not disassemble the lamp.
8. Please do not dispose the battery with household garbage to avoid explosion.

Installation

Adjust light and bracket angle

1. Prepare the lamp
   Prepare lamp, accessories and tools well firstly.

2. Adjust light angle
   Use Allen wrench to loosen the light panel and adjust it to the demanded lighting angle, then fix the screw tightly.

3. Adjust bracket angle
   Rotating the screw to loosen the bracket, adjust it to the appropriate angle.

4. Fix the screw
   After adjusting the angle fix the screw tightly.

Mount on the wall

1. Drill the holes
   Please use the measure card to drill 2 holes of Φ8mm with a spacing of 150mm.

2. Put plugs and screws in wall Put the plugs and screws in to the wall.

Put on flat surface

1. Place lamp on wall
   Fix the lamp onto the wall with expansion plugs and screws.

Note: The recommended mounting height is 2-4 meters.

FlinQ Commerce

Address: Eemweg 74 3755 LD Eemnes The Netherlands
Web: www.flinqproducts.nl
Email: info@flinqproducts.nl

References

• FlinQ Products | Gratis verzending | 2 jaar garantie | Betaal later

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>