TESLA DB600SX Cooker Hood User Manual
- June 4, 2024
- Tesla
Table of Contents
COOKER HOOD
DB600SX/DB600SB/DB600SW/DT600SX/ DT620SX
User Manual
Product images are for illustrative purposes only and may differ from the actual product.
CLASSIC COOKER HOOD
BUILT-IN HOOD
| Check the electrical
connection| Check the power buttons| Check the lightning
buttons| Check the aluminum filters
(the aluminum filters must
be washed once In every
month.)| Check the bulbs/spots| Check the air outlet (It must be open)| Check
the carbon fitters
(the carbon fitters must be
changed in every 3 months)
---|---|---|---|---|---|---|---
Cooker Hood is not working| X| X| | | | |
Lightning not working| X| | X| | X| | X
The cooker hood does not perform well| .| | | X| | X|
CONTROL PANEL
On/Off
1. Motor runs on Level 1
2. Motor runs on Level 2
3. Motor runs on Level 3
Lamp On / Off
Lighting
Light On / Off
Fans
0 Fan Off
1 Fan level 1
2 Fan level 2
3 Fan level 3
**RECIRCULATION MODE
**
Step 1
The exhaust hole will be closed with a plastic cover.
Step 2
Place the charcoal filter. (optional*)
Step 3
Remove the long plastic part.
Step 4
Put the short plastic part.
Step 5
The hood is ready for use.
For the purchase of carbon filters, please contact your dealer to obtain the
corresponding reference to your model.
REPLACING THE ACTIVE CARBON FILTER
(Circulating air mode only)
To maintain odor insulation levels, regular care of the filter is necessary.
The active carbon filter should be replaced every 4 months.
INFORMATION
- Active carbon filters are not included in the delivery. Active carbon filters may be purchased from your dealer, customer service, or a store online.
- Active carbon filters cannot be cleaned and reused.
- Remove the metal grease filter.
- Turn the old active carbon filter and pull it from its slot.
- Place a new active carbon filter in the slot, press it down and turn it.
- Reinstall the metal grease filter.
Dear User
Our aim in presenting you with this manual is to ensure that you can use our
aspirators, produced with state-of-the-art technology within our modern
facilities and supplied to the market subsequent to strict quality controls,
in the most efficient way.
We recommend your esteemed side read carefully this manual and keep it handy
to use it again if required prior to providing information on usage.
WHAT TO DO BEFORE INSTALLATION AND USAGE
- Do not connect the exit of your aspirator to flues where devices like stoves or water heaters are connected and where there is the circulation of hot gases.
- The distance between the bottom surface of your aspirator and the upper surface of electric ovens should be 65 cm stove while the distance should be 75 cm stove between the bottom surface of your aspirator and the upper surface of ovens using gas or mixed fuels. Otherwise, the product will be definitely out of warranty!
- Insert the plug of your aspirator into the socket when all the user switches on the control panel are in the closed position.
- Installation and wiring should be carried out through our authorized services. Our company is not responsible for failures arising due to installation by third parties.
- Be careful that the power cord is not compressed and crushed during installation. A hole through which the plug of the aspirator can pass easily must be opened without cutting the aspirator cord and installation must be carried out in this way. If the power cord is damaged it must be replaced through our authorized services.
- If the supply cord is damaged, this cord must be replaced by the manufacturer or its service agent, or equally qualified personnel to prevent a dangerous situation.
- Flaming foods should not be cooked under the device. They may cause a fire.
- The air discharge pipe should be aluminum. The air discharge pipe should have a length of 120 mm. and the louver culvert should be assembled to the outlet at the exterior without fail. Place the pipe for the flue outlet outside never narrowing the diameter of the pipe (120 mm)
- Do not use non-fire-resistant filtering materials (such as paper) on the filter.
- Turn the unit off and take the plug from the socket prior to the maintenance process.
- Use a max 6 amp fuse for your safety.
Your aspirator is produced to work with and without a flue connection.
USAGE WITH FLUE
There is an air exit on your aspirator. A flue connection will be made from
this air exit. A flue adapter suitable for 120 mm diameter is supplied with
the aspirator. It is recommended to use a spiral pipe with a diameter of 120
mm in the flue pipe. The pipe connection should be as short as possible and
with the least number of elbows for efficient operation of your aspirator.
USAGE WITHOUT FLUE
Closet shelves or cabinet ceilings that may prevent the outlet pipe should be
cut in the same size to ensure air circulation in the kitchen. The air sucked
by the aspirator is given into the kitchen in usage without a flue. A culvert
should be installed at the mouth of the pipe on the facade. Replace your
carbon filter every 3 months on average.
FILTER CHANGE (WASHING)
- Remove the cassette filter by pushing the latches inside.
- Place one side of the filter into the house and secure the filter by pressing inside and leaving the latch on the other side.
IMPORTANT NOTICE
- The distance between the bottom surface of your aspirator and the upper surface of electric ovens should be 65 cm stove while the distance should be 75 cm stove between the bottom surface of your aspirator and the upper surface of ovens using gas or mixed fuels. Otherwise, the product will be definitely out of warranty!
- Place the flue exit in the same diameter (without making it smaller).
- Do not operate your aspirator without a filter.
- Do not change the filter while your aspirator is running.
- Operate your aspirator while you operate your stove.
- Do not open your aspirator when you feel a gas leak.
- Wipe your aspirator with a cloth soaked in warm water with detergent and dry.
- You may use the aluminum filter by washing it at least once a month
- Replace the oil filter with synthetic fiber every 2 months
- Replace the imported carbon filter every 3 months in use without a flue.
- Ventilation of the room should be sufficient if you are operating your aspirator with products using gas or similar fuel at the same time.
- Ensure that the children and people with physical and mental disabilities do not use the appliance.
MOUNTING AND INSTALLATION OF THE EXTRACTION HOOD
There are 2 eyelet marks on the back part of your hood for hanging the hood.
- Determine the place of the hood which has to be hanged on a plane surface and at a height of 65 cm from the oven and mark the hanging hole places.
- Use a 08 mm drill for drilling and drive the screws by placing dowels.
- Hang the hood by using the hanging screws and fix it.
- There are 2 flues in the parcel of the hood. The short flue is used for selling the height and the short flue will be placed in the long flue.
- Place both flues on the hood at the same time. Make the flue height adjustment by sliding the short height adjustment flue from inside upwards.
Drill the 2 eyelet marks on the back part of the hood and hang the hood on the wall by placing dowels and screws. Place the long flue on the hood by sliding it down on the short flue. This may assembly of the hood will be completed.
Documents / Resources
|
TESLA DB600SX Cooker
Hood
[pdf] User Manual
DB600SX, DB600SB, DB600SW, DT600SX, DT620SX, DB600SX Cooker Hood, DB600SX,
Cooker Hood, Hood
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>