kogan KALED42RF7510SPA 42 Inch Smart FHD LED TV User Guide
- June 9, 2024
- Kogan
Table of Contents
kogan KALED42RF7510SPA 42 Inch Smart FHD LED TV
COMPONENTS
- A Kogan 42″ SMART FHD LED TV
- B Remote control
- C Stand (x2)
- D ST4x12mm screw (x4)
- E AAA battery (x2)
- F Quick-start guide
- G Warranty card
NOT INCLUDED
Phillips head screwdriver, antenna cable, broadband internet connection.
REMOTE CONTROL OVERVIEW
- Power Switch between working and standby status.
- Mute
Turn on/off the sound. - Number keys Select the channel or input numbers.
- Return to previous channel.
- AD Turn on/off the associated audio.
- LIST Show channel list.
- FAV Show the list of favorite TV channels.
- GUIDE Electronic program guide.
- NETFLIX Open Netflix application.
Open Net Range application store.
Open You Tube application.
Open Prime Video application.- Menu ( ) Show OSD menu.
- Home( ) Show home page.
,.A.,T ‘ Select items or adjust values.- 0K Confirm the operation.
- Return
Return to previous menu page, or return to previous channel. - Exit
Exit OSD menu or application. 
Turn up/down the volume.- CH+/-
Change program channel. 
Quick menu.- Show signal source menu.
- Red key Special function keys.
- Green key
- Yellow key
- Blue key
- AUDIO Select audio language.
- TTX Open / Close teletext.
- SUBTITLE Select subtitle language.
Show information bar.
Enter the next item.
Return to the last item.- Fast backward.
Fast forward.- Record Start to record current program.
STOP.- Time shift key. (PAUSE)
- (play) Play function in multimedia.
ASSEMBLY AND INSTALLATION
BEFORE YOU GET STARTED
Spread cushioning out to lay the TV on. This will help to prevent damage.
-
Stand assembly
-
Attach stands to base of TV.
-
Insert two ST4x12 mm flat tail self-tapping screws for each stand, and use Phillips head screwdriver (not supplied) to tighten.
-
Remote control assembly
-
Open the battery compartment cover on the back side.
-
Insert two 1.5V AAA size batteries, making sure to match the polarity markings (+I-) of the batteries with the diagram inside the compartment.
-
Replace battery compartment cover.
-
Connect to antenna
-
Connect an antenna cable (not supplied) via the ‘ANT input port at the back of the TV.
-
Ensure the antenna cable is also connected to a working antenna, either via an antenna wall socket in your home, or directly.
-
Turning TV on
Connect the power supply, enter the standby mode, press the power button of the TV or the power button on the remote control to turn on the TV.
TURNING TV OFF
Press the POWER button on the remote control to enter standby mode. To power
down the TV completely, unplug the power cord from the power outlet.
Do not leave your set in standby mode for long periods of time. If you will not use the TV for a long time, it is recommended to unplug the set from both the power outlet and aerial.
FIRST TIME SETUP
The first time you switch your TV on, it will automatically be in the initial setup mode. This will guide you through the whole setup process of selecting your desired language, connecting to the internet, signing in to your account and tuning in TV channels.
Choosing Your OSD Language
-
Press the buttons to highlight your desired OSD language then press the OK button.
-
Press the buttons to select your country where you will operate the TV. Press the OK button to confirm.
-
Data Collection and Firmware Updates Notice page will appear. Press the◄►buttons to select the menu option.
-
Press the button to select the network type.
-
Press the button to select your TV Mode.
-
Press the button to select your tuner mode.
-
Press the button to select your Scan Mode.
BASIC OPERATIONS
Signal source selection
You can connect various devices to the TV set and view high quality images. If
the video device has HDMI, AV and other video output ports, you can select one
of them and connect to corresponding input ports of the TV set. After
connected, turn on the device and press 
key, then menu of signal
source will be displayed on the screen. Press 
key to select the
input signal, and press [OK] key to confirm.
Menu operation description
Press key to show the main menu on the screen:
- Press
key to select a menu from Video, Audio, TV, Setup, Parental, About. - Press [OK]/[►] key to enter the submenu.
- Press key to select an item in the menu.
- Press [OK] key to confirm.
- Press [◄]/[►]key or key to adjust the value or setting.
- Press key to return to previous menu when the TV displays the submenu.
- During menu operation, the icons of invalid options will change into grey.
Note: The default password for the lock system is 0000.
Smart TV
Press [A] key to show the home page.
- Press [◄]/[►]key to select an application;
- Press [OK] key to run the application;
- Press
key to exit the smart mode.
Note: Before accessing the Internet, please connect your TV set to the Internet. Refer to “Network Settings” for details.
Channel scanning
Scan the channels before watching the TV for the first time. Before scanning,
please make sure that the antenna has been connected properly, and select the
signal source as ATV or DTV.
ATV Scanning
After selecting ATV source, press 
key, and Select TV, then
press [OK] key to enter.
- Select Channel Scan, and press [OK] key, then the machine starts auto scanning.
- Select Analog Manual Scan, and set Start Frequency (MHz). Select Scan Up or Scan Down, and press [OK] key to manually search for channels.
DTV Scanning
After selecting DTV source, press key, and select TV> Tuner
Mode> DVBT/DVBC according to your needs.
After select DVBT.
- Select TV> Channel Scan, and press [OK] key, then the machine starts auto scanning.
- Select TV > Manual Scan > RF Channel, and press [►] key to enter. Select channel, then press [OK] key to manually search for channels.
After select DVBC.
- Select TV> Channel Scan, and press [OK] key to enter. After setting Scan Mode, select Scan, then press [OK] key to search for channels.
- Select TV> Manual Scan, and set Frequency (KHz), Modulation, Symbol Rate (Ksym/s). Select Scan, then press [OK] key to manually search for channels.
APP
Press [ ] key, then press [◄]/[►]key to select an application and press [OK]
key to enter. As to YouTube, prime video, Entrange and Netflix, you can press
the [YouTube], [prime video], [Entrange] and [NETFLIX] keys to use them. In
the standby mode, you can turn on the TV and use Netflix by pressing [NETFLIX]
key on the remote control.
Network settings
Press key, then select Setup>
Network> Configuration> Interface, select Wireless or Ethernet.
- Wireless
- After selecting Wireless, press [OK] key, then select Wireless Setting > Scan, and press [OK] key, then the wireless network signals are searched by your machine list automatically. The network searched without icon indicates that the machine connects to the network without a password. The network with icon indicates that it is encrypted and you must enter the correct password to connect to the network;
- Select the network you want to connect to in the network list, and press [OK] key;
- Type network connecting password in the box and exit keyboard, then select Connect and press [OK] key to connect to network.
- If the network is hidden, select Wireless Setting> Manual, and press [OK] key to enter. Set the network name (SSID), and press[►] key to enter. Select security mode, then enter the correct password to connect.
- If you select Wireless Setting > Auto, then enter the PIN or PBC to automatically connect to the network.
- Ethernet
- After selecting Ethernet, press [OK] key, then select IP Setting > Address Type> AUTO, and your machine will connect to the Network automatically;
- Select Address Type> Manual, and press [.A.]/[T] key to select IP Address, Subnet Mask, Default Gateway, Primary DNS and Secondary DNS to set them. Then press [:)] key, your machine will connect to the Network automatically.
Wake On Lan/ Wake On Wlan
It allows remote systems to wake up the sleeping TV by sending a frame of a
specific format which the client anticipates. (It is available when network is
connected.)
Press [ ] key, then select Setup > Network > Configuration > Wake On Lan /
Wake On Wlan, and press [OK] key to enter. Press key to set it as “On”
or “Off”, and press [OK] key to confirm.
BASIC TROUBLESHOOTING
Poor picture and sound quality
- Try a different channel
- Adjust the antenna
- Check all connections
No picture or sound in TV status
- Try another channel
- Press the TV/AV button
- Make sure TV is plugged in
- Check the antenna connection
No sound or sound is too low at maximum volume
- Check the volume settings on any external speakers connected to your television
- Adjust the TV volume accordingly
- Check another channel or input
- Check that MUTE hasn’t been turned on
No color, wrong color or tints
- Make sure the program itself is broadcast in color
- Select the picture menu, then adjust the color and tint submenus
Picture rolls vertically
- Check all connections
Blurred or snowy picture, distorted sound
- Check direction, location and connections to your antenna
- Issues may be caused by the use of an indoor antenna (poor signal)
Remote control malfunctions
- Replace remote control batteries
- Check battery terminals
- Remote is out of range, move closer to TV
- Remove any obstructions between remote and IR sensor of TV
- Make sure the power cord to your TV is plugged in and turned on
Image is not centered on the screen
- Adjust the horizontal and vertical position
“No Signal” on HDMI source
- Test the device with a different HDMI cable
- Plug the device into another HDMI port
- Try a different device connected to the same cable and port
- Perform a factory reset on your TV
For our full TV troubleshooting guide and extended User Manual for this TV, head online to help .kogan.com
Need more information?
This is a Quick Start Guide, and while we hope that this has given you the
assistance needed for a simple set-up, a full user guide outlining all of this
product’s instructions and features can be found online at
help.kogan.com