Dextra Tanek Luminaire Finder Installation Guide

June 9, 2024
Dextra

Dextra Tanek Luminaire Finder

Dextra-Tanek-Luminaire-Finder-PRO

Terminal Labelling

Power

  • L1 Switched Live
  • E Earth
  • N Neutral

Emergency

  • L2 Unswitched Live
  • DA/AT3 DALI Autotest
  • DA/AT3 DALI Autotest

Dimming

  • -/D1/DA Analogue/DSI/DALI
  • +/D2/DA Analogue/DSI/DALI
  • L3 Switch Dim / Corridor Function

WARNING

  • Luminaire must be earthed. Risk of electric shock from LED boards if operated with cover removed.
  • Installation/operation outside of luminaires intended scope invalidates warranty.
  • Suitable only for domestic/light industrial/industrial applications within the scope of EN55015.
  • Tested to compliance with BSEN 60598: specification for general requirements and tests.
  • Must be installed by a suitably qualified person in accordance with all relevant legislation.
  • Ambient operating temperature of 0°C to 25°C. If maximum operating temperature is exceeded luminaire will automatically dim/switch off.
  • Terminal blocks are rated to 16A unless stated otherwise. The light source is nonreplaceable.

LUMINAIRES WITH EMERGENCY PACK

  • When supply is isolated battery output terminals may be live if battery is connected.
  • Isolate mains and battery before servicing.
  • Emergency luminaires require unswitched live connection taken from same phase as switched supply.
  • When unswitched supply is connected status indicator illuminates green, when unswitched supply is disconnected indicator extinguishes and luminaire operates in emergency mode.
  • 24 hour charge period required before undertaking full discharge test.
  • Emergency test sheets provided should be used to record all emergency tests.
  • Batteries should be replaced when 3 hour duration is not met.
  • Excessive switching of permanent live may result in premature battery failure.
  • Battery electrolyte can be harmful to eyes / open wounds, do not puncture, if electrolyte touches skin/eyes flush with water.
  • Do not incinerate batteries.

INSTALLATION

  1. Carefully unpack the luminaire and undo the 10 x M5x20 socket screws in the frame and lift the entire frame from the housing.Dextra-Tanek-Luminaire-Finder-2

  2. Undo the 2 x M4x10 machine screws in the ends of the gear tray as show in the image and remove the gear tray from the housing.Dextra-Tanek-Luminaire-Finder-3

  3. Drill suitable fixings to suit required installation.Dextra-Tanek-Luminaire-Finder-4
    NOTE: IT IS THE CONTRACTORS RESPONSIBILITY TO ENSURE THE HOLES ARE SEALED. FAILURE TO SEAL THE HOLES WILL INVALIDATE THE LUMINAIRE’S IP RATING.

  4. Remove the female socket from the tray as shown and hard-wire to the mains supply.Dextra-Tanek-Luminaire-Finder-5

  5. Reconnect the plug to the tray leaving sufficient cable length to reach.Dextra-Tanek-Luminaire-Finder-6

  6. Carefully return the gear tray into the housing and secure into place with the 2 x M4x10 machine screws provided. Ensure the mains cable does not become trapped when doing so.Dextra-Tanek-Luminaire-Finder-7

  7. Feed the toggles on the tether wires through one of the 7mm rounds on the end brackets inside the housing. Hole location as shown to the right.

  8. Reverse step 1 to secure the frame back onto the housing. Do not over tighten the socket head screws when replacing the frame. Tighten sufficiently so to provide a seal between the frame gasket and the housing.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals