HUANANZHI B660M-PLUS M-atx Motherboard User Manual

HUANANZHI B660M-PLUS M-atx Motherboard

Product Information

The BM-PLUS is a motherboard manufactured by SZ HUANAN SANXIAN TECHNOLOGY CO.,LTD. The motherboard comes with an ESD protection feature and supports DDR4 RAM up to 128GB. It has an I/O panel that includes 6 SATA ports, 2 USB 2.0 ports, 4 USB 3.1 ports, a PS/2 port, an RJ45 port, an HDMI port, and a VGA+DP port. The motherboard also has Realtek LAN and audio drivers, and supports Wi-Fi connectivity.

Product Usage Instructions

Before assembling the computer, it is important to follow the safety precautions mentioned in the user manual. Make sure all parts are firmly connected to avoid failure in recognizing components or starting the computer. Also, place the power cord where it will not be stepped on and avoid placing anything on it.

Once the safety precautions have been taken care of, proceed with the installation and settings. Confirm that the motherboard is properly packaged upon purchase of the product and in case of any damage to packaging or lack of accessories, contact the manufacturer as soon as possible.

Install the necessary drivers such as chipset driver, sound card driver, and LAN driver. These drivers can be downloaded from the manufacturer’s website. After completing the driver installation, proceed with BIOS settings. The BIOS setup includes options such as system overview, advanced settings, boot settings, security settings, save settings, and exit options. Refer to the motherboard diagram and rear I/O panel for better understanding of the product layout and connectivity options. The BM-PLUS motherboard supports Intel CPUs and has a CPU LGA socket with CPU pins. It also supports SATA storage devices.

SAFETY PRECAUTIONS

• Products could probably be damaged due to electrostatic discharge(ESD). Please follow these steps below for a successful computer assembly.
• Make sure all parts are firmly connected; otherwise, it might lead to the failure of recognizing components or starting the computer.
• Place the power cord where it will not be stepped on. Do not place anything on the power cord.
• Hold the border of motherboard when taking it out. Do not touch the sensitive parts of motherboard.
• Please put the motherboard in an anti-static container or on anti-static pad if not needed.
• Before turning on the computer, make sure all parts inside the case are firmly connected without any loose screws or metal components.
• Do not start the computer before installation finished, otherwise it might result in permanent damage to the computer parts or even injury to the user.
• If you need any assistance in the process of installation，please contact our after-sales customer service or reach us on HUANANZHI official E-mail: business@huananzhi.com for professional technical support.
• Prior to installation or disassembly, please switch off the power and pull the power cable from the socket.
• Keep the motherboard away from moisture.
• Keep the user manual for future reference.
• Before plugging the power supply, please make sure the socket provides the corresponding voltage.
• In any of the following situations, please keep the motherboard and power cable in a safe place. Do not put anything onto the power cable.
• In the event of any of the following conditions, have the board checked by a service technician:
  • Liquid penetrated into the computer.
  • Motherboard is exposed to moisture.
  • Motherboard does not work even if you follow the instructions on user manual.
  • Motherboard fell off to the ground and got damaged.
  • Motherboard has clear signs of damage.

PACKING

• Please confirm that the motherboard is properly packaged upon purchase of the product. If there is any damage to packaging or lack of accessories, contact us as soon as possible.

1. **1*** HUANANZHI B660M-PLUS Motherboard
2. **1*** SATA data cable
3. **1*** 1/O shield back plat
4. **1*** Warranty card

BRIEF INTRODUCTION

Features

• CPU: Intel ® 12th13th Generation LGA1700 processor i3/15/i7 Intel ® Core ™M
  • Intel ® 12th13th Generation LGA1700 processor Intel ® Xeon ™M
  • Intel ® 12th 13th Generation LGA1700 processor Intel ® Pentium™
• RAM: 2*DIMM RAM SLOT supports up to 64GB DDR4(Support for overclocking)
  • 3600/3200/2666/2400/2133MHZ Non-ECC memory
  • G1 Mode 2133-3200MHz/G2 Mode 2133-3600MHz
  • Two-Channel Memory Architecture
  • Actual memory data rate depends on CPU type and DRAM module
• 1/O effects: 4 x SATA3.0 (maximum transfer speed up to 6GB/s)
  • 4 x USB2.0 interface
  • 4 x USB3.2 ports
  • 1 x PS/2 Mouse and Keyboard port
  • 1 × RJ45 Network card interface
  • 2 × HDMI-Compatible
  • 1 × VGA+ DP interface
• Audio: Realtek Audio Transcoder
  • Realtek 5.1 Channel High Fidelity Audio
  • Audio output: Front Out/Front Speaker Out
  • Audio input: Microphone input, Audio input
• Ethernet: 1 x Realtek RTL8125BG 2.5Gbps LAN
• Expansion slot: 1 × PClex16 4.0/5.0
  • 1 x PCIex1 3.0
  • 1 x PCIex4 3.0
  • 1 x M.2 NVME PCle 3.0X4 (key M)2260/2280
  • 1 x M.2 NGFF SATA3.0
  • 1 x M.2 WIFI(Support NGFF/CNVI)

MOTHERBOARD IMAGE

B660M-PLUS Motherboard Illustration

Rear I/O Panel

Overall Rear I/O Panel Display

LAN Port Status Table

Audio Port Configuration

Installation And Settings

NOTICE: please check the motherboard where all pins marked with number “1” or white bold line are position “1”

Clear CMOS Jumper CLR-CMOS

Front Audio Output Ports

Expansion Ports

PCI Expansion Slot

F_PANEL1 Boot Interface

USB 3.2 Interface

CPU Installation

• To properly place the CPU in the motherboard,the Cpu base of the LGA1700 motherboard has two salient points and a golden triangle indicator.Golden triangle indicates Pin1.

M.2 Interface Installation

1. Remove the screw from the screw base
2. Remove the screw base
3. Tighten the screw base screwed into the length M.2 module to the M.2 interface distance hole
4. Insert your M.2 module into the M.2 interface at a 30 degree angle
5. Place the screw on the trailing edge notch of your M.2 module and tighten to the screw base.

Memory Installation

1. Pull the clips on both ends of the memory slot outward, and the memory strip corresponds to the protruding position of the slot to determine the direction of installation.
2. Align the memory module into the slot and press
3. Let the snaps on both ends of the slot automatically bounce.

Graphics Card Installation

1. Use a screwdriver to remove the bezel and screws on the main unit
2. Need to pick up the card slot of the card slot when installing the graphics card
3. Insert the graphics card into the card slot of the graphics card
4. After the installation is in place, the chuck will automatically return to its position.
5. Secure the graphics card to the chassis with screws
6. Install the power cord

SATA Interface

Drivers installation

Drivers listing

Intel Chip Information Installation

Run “Control Panel – System – Hardware – Device Manager” Click the right mouse button to change the driver’s hardware device and proceed with the installation below:

Option: Propertyl – Update driver| – Not connect to Internet –

• Manually installation
• Find the corresponding directory
• Select “Next step”

Audio driver installation

Before this installation, please check the model of the audio chip on the motherboard first (you may refer to this manual), Select the proper driver accordingly for installation.

Audio driver installation (take HD Audio series for example)

• Run “driver installer”: B660M-PLUSAudio/Realtek/windows10- 11/Setup.exe
• Click on “next”to continue,and then”finished”
• The system will automatically restart itself to finish the installation

Uninstallation of audio driver (take HD Audio series for example)

Setting into Windows desktop, choose “setting”/ “control”,and then “add/remove programs”. Later, choose “Realtek High Definition Audio Driver” in the menu and click on ” add/remove”so that the driver will be automatically removed.

Driver installation of external video card

• Run “driver installer”, take Setup.exe, Click on “next”- “yes”
  • “next”
  • “next”and”finished”h
• The system will automatically search for devices to complete the installation

Driver installation of network

• Run “driver installer”: B660M-PLUS LAN/Install_Win101001 05292015.exe
• click on “next”-
• “installation”- “finished” and restart the computer and restart the computer, The system will automatically search for devices to complete the installation.

BIOS Settings

In order to enable the computer to work well or execute specific functions, CMOS SETUP normally stores all kinds of data in CMOS SRAM of the motherboard. When the computer is shut down, motherboard’s battery will supply power to CMOS SRAM. When the computer is turned on and starts POST(Power On Self Test), press “Delete/Del” key to enter into AMI BIOS CMOS SETUP main page. Motherboard warm boot key is“ F7”

Menu: please pay attention to every option in the settings menu. When there is a triangle shaped symbol on the left side of menu, it means that you choose this sub-menu,so a pop-up sub-menu will be available.

Main Menu Function

• Main
• System Overview
  • Date/Time settings, HDD specs/Monitor type settings.
• Advanced
  • Advanced Settings
  • BIOS special function settings, such as virus alert, booting disk priority etc.
• Chipest
  • Advanced Chipest Settings
• Dverciocking
  • Memoru XMP Profile
• Boot
  • Boot Settings
• Security
  • Security Settings
• Save
  • Save Setting
• Exit
  • Exit Options
  • Exit settings include loading of optimized defaults value/ loading of fail-safe defaults / discarding changes/ exiting without saving.Exit settings include loading of optimized defaults value/ loading of fail-safe defaults / discarding changes/ exiting without saving.

SZ HUANAN SANXIAN TECHNOLOGY CO., LTD.

• WWW.HUANANZHI.COM

References

• 华南金牌官网

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>