CLAGE Hot Air Hand Dryer WHT Owner’s Manual

June 9, 2024
CLAGE

CLAGE Hot Air Hand Dryer WHT

CLAGE-Hot-Air-Hand-Dryer-WHT-product

Product Information

This product is a CLAGE water heater, designed for installation and use in various countries. It has various safety features, including an automatic shutdown if the sensor detects overheating or if there is a power outage. The heater also has a sensor to detect water flow and adjust the heating accordingly. The installation requires mounting the heater on a plate and connecting it to a water source and electricity.

Product Usage Instructions

Before using the CLAGE water heater, please read the instructions carefully to avoid any potential risks or damage to the product.

Installation

  1. Mount the heater on a plate using the provided instructions (see Abb. C, D).
  2. Connect the heater to a water source and electricity, following local regulations and codes.

Inbetriebnahme (Startup)

  1. Before first use, ensure that all safety features are correctly installed by checking the manual (see 4. Inbetriebnahme).
  2. Turn on the heater by following the instructions (see 4. Inbetriebnahme).
  3. The sensor will detect water flow and adjust heating accordingly.
  4. If there is a power outage or overheating, the heater will automatically shut down.

(Emergency Procedures)

  1. If there is an emergency, immediately turn off the heater by unplugging it or turning off the circuit breaker.
  2. Secure the heater to prevent accidental re-startup.

(Troubleshooting and Repair)

  1. If there is an issue with the sensor or heating, refer to the troubleshooting section in the manual (see 6. Fehlersuche und Reparatur).
  2. Do not attempt to repair the heater yourself, but contact customer service for assistance.

Regular maintenance, such as cleaning the sensor and air intake grille, is also recommended (see 7. Wartung).

Finally, ensure proper recycling of the product at the end of its life cycle (see 8. Recycling).

Safety instructions

Carefully read the operating instructions all the way through before operating the equipment and retain them for future reference. The pictures in these instructions refer to all available versions of the model and may be different from the actual scope of delivery.

Explanation of symbols and signs used

  • This is the warning symbol. It warns against possible risk of injury. Follow all instructions which are marked with this sign to avoid injury or death. The warning symbol always appears in association with the signal words DANGER, WARNING and CAUTION.
Symbol Signal word Description
DANGER Identifies a hazard with a high degree of risk which will

cause death or seri- ous injury if not avoided.
| WARNING| Identifies a hazard with a medium degree of risk which could cause death or serious injury if not avoided.
| CAUTION| Identifies a hazard with a low degree of risk which could cause minor or moderate injury if not avoided.
1./2./3.| | Identifies steps to be taken one after the other by the user.

Qualification of operating, installation and maintenance personnel

  • The installation and electrical connection may only be executed by trained qualified personnel.
  • Maintenance may only be performed by persons who have been trained to handle the device and explicitly assigned to this task.
  • This device may be used by children aged 3 and over as well as by persons with reduced physical, sensory or mental capacities or a lack of experience and knowledge if they are supervised or have been instructed on safe use of the device and understand the associated risks. Children must be supervised to ensure that they do not play with the device.

Intended use

  • The device is used to rapidly dry hands.
  • The device is intended for commercial use, for example for use in hotels, public baths, fitness studios, spas, saunas, public facilities, industries and businesses.
  • The manufacturer does not accept liability for damages caused by misappropriation, inappropriate usage or incorrect repairs.

Avoid danger from electric shocks

  • The voltage on the rating plate must match the mains voltage. Only connect the vacuum cleaner to a sufficiently protected electric socket.
  • Do not pull the mains connection cable over sharp edges, do not bend it or clamp it. Only replace a damaged mains connection cable with one meeting the specifications in the Technical Data chapter.
  • Do not operate the device including the accessories in the following cases:
    • Power cord is defective or has cracks
    • Device is noticeably damaged, e.g. by cracks in the housing
    • If an invisible defect is suspected, e.g. after a fall or impact
  • In the following cases, unplug the power cord, switch off the circuit breaker or unscrew the fuse:
    • When the device makes unusual noises
    • Before any maintenance or cleaning
  • When unplugging, only pull on the mains plug and not on the mains connection cable. Never touch the mains plug with wet hands.

Avoiding risks during installation

  • For the installation and operation of the device, please observe:
    • The national and regional regulations
    • The technical regulations and guidelines
    • The provisions of the local authorities

Avoiding risks during operation

  • Do not use the device in rooms with toxic, explosive or flammable fumes and gases, or with microbiologically contaminated air.
  • Do not insert any objects into the opening of the device. Do not cover the device or deposit objects on it.

Avoid any danger during maintenance and repair

  • Only have repairs carried out by experts. Only use original accessories and spare parts.

Device structure

When ordering spare parts, please always specify the appliance model and serial number.CLAGE-Hot-Air-Hand-Dryer-WHT-fig-1 CLAGE-Hot-
Air-Hand-Dryer-WHT-fig-2

  1. Device
  2. Mounting plate
  3. Sensor
  4. Outlet opening
  5. Air intake grille
  6. Locking screw
Installation

Unpacking

  1. Take all of the parts out of the packaging.

Scope of delivery

  • 1 device
  • 1 mounting plate
  • 4 screws
  • 4 dowels
  • 1 screw for the electric terminal cover

Installing the mounting plate

CLAGE-Hot-Air-Hand-Dryer-WHT-fig-3 CLAGE-Hot-
Air-Hand-Dryer-WHT-fig-4

CAUTION

  • Unsuitable installation material!
  • Risk of injury caused by the device falling down.

Before installation

  1. Check if the screws and dowels supplied with the device are suitable for the surface material.
  2. Select a wall with a sturdy, weight-bearing surface.
  3. Observe the installation height and minimum distances.
  4. Have suitable fastening material to hand for installation on the wall.
  5. Use the mounting plate as a template on the wall to mark the drill holes.
  6. Drill the holes.
  7. Fasten the mounting plate on the wall.

Installing the device

CLAGE-Hot-Air-Hand-Dryer-WHT-fig-5

CLAGE-Hot-Air-Hand-Dryer-WHT-fig-7

CLAGE-Hot-Air-Hand-Dryer-WHT-fig-8

DANGER

  • Live electrical supply line and device components!
  • Risk of deadly electric shock in case of contact.

Before performing any work on the device

  1. Unplug the power cord. With direct connection: Switch off the circuit breaker or unscrew the fuse.
  2. Secure against accidental switching on.

Observe the following conditions for the electrical connection

  • Only connect the device to a properly installed grounded socket.
  • With fixed connection: The supply line must have a switch-off device, e.g. a circuit breaker that can be switched off or a screw-in fuse.
  • Connect the device to an electrical supply line with a residual current circuit breaker.
  • Do not connect other loads to the electrical supply line of the device.

CAUTION

  • The device can become detached from the mounting plate!
  • Risk of injury caused by the device falling down.
  • The locking screw for the air intake grille also serves to fasten the device to the mounting plate.

If the locking screw is not properly tightened

  1. Ensure that the device cannot be accidentally pushed off of the mounting plate.
  2. Unscrew the locking screw on the air intake grille on the underside of the device.
  3. Pull the air intake grille downwards out of the device.
  4. Remove the electric terminal cover.
  5. Connect the electrical supply line to the terminal, see Fig. F.
  6. Put the electric terminal cover back on.
  7. Attach the electric terminal cover with the screw.
  8. Insert the device from the top in the 4 lugs on the mounting plate.
  9. Push the device down up to the stop.
  10. Put one hand on the top of the device to hold it and insert the air intake grille into the device from the bottom.
  11. Fasten the air intake grille and the device with the locking screw.

Initial operation

Please observe the following before initial operation Ensure that the following requirements are met:

  • The minimum distances have been maintained.
  • The power supply is properly connected.
  • All filters are inserted and undamaged.

Switching on and off

The device is switched on and off without contact by means of the sensor:

  1. Hold hands or head under the outlet opening of the device.
    • The sensor automatically switches on the device.
    • The device is switched off as soon as hands or head are removed from the sensor range.
    • The device is automatically switched off if hands or head remain in the sensor range for a longer period of time: 35 seconds

Safety features

The hand dryer is equipped with the following safety features:

  • Safety cut-off sensor after 35 seconds
  • Safety temperature limiter in case of overheating, e.g. if the outlet opening is blocked

Conduct in case of emergency

In cases of fire hazard, electrical shock, mechanical damage, unusual operating conditions or misuse, proceed as follows:

  1. Unplug the power cord. With direct connection: Switch off the circuit breaker or unscrew the fuse.
  2. Secure against accidental switching on.

Troubleshooting and repairs

Malfunction Cause Remedy
The device does not start Sensor is soiled Remove dirt from the sensor and

wipe with damp cloth
Overheating due to blocked out- Clean out the outlet opening, let opening allow the device to cool down
Air output is insufficient| Air intake grille is soiled| Clean the air intake grille

  • Do not take any further action; contact customer service instead.

Maintenance

DANGER

  • Live electrical supply line and device components!
  • Risk of deadly electric shock in case of contact.

Before performing any work on the device

  1. Unplug the power cord. With direct connection: Switch off the circuit breaker or unscrew the fuse.
  2. Secure against accidental switching on.
Cleaning the air intake grille

CAUTION

  • The device can become detached from the mounting plate!
  • Risk of injury caused by the device falling down.
  • The locking screw for the air intake grille also serves to fasten the device to the mounting plate.

If the locking screw is not properly tightened

  1. Ensure that the device cannot be accidentally pushed off of the mounting plate.
  2. Unscrew the locking screw on the air intake grille on the underside of the device.
  3. Pull the air intake grille downwards out of the device.
  4. Remove any lint and adhering dirt from the air intake grille.
  5. Put one hand on the top of the device to hold it and insert the air intake grille into the device from the bottom.
  6. Fasten the air intake grille and the device with the locking screw.

Cleaning the device

Do not clean the device with a high-pressure cleaner. Only use a damp cloth and mild cleaning agents to clean the device. Acids, acetone or solvents can damage the housing or device components.

Disposal

Old equipment contains valuable materials which are designed for re- processing. The vacuum cleaners must not be thrown away in the normal household waste, but should be disposed of at a suitable proper collection system, e. g. via your communal disposal location.

Technical data

Type WHT
Voltage V
Frequency Hz
Power consumption (max.) W
Fuse A
Motor output W
Air volume l/s
Air speed m/s
Sound level dB(A)
Protection class II
Protection type IP
Relative drying time s
Width mm
Depth mm
Height mm
Weight kg

CLAGE GmbH

  • Pirolweg 1–5 21337 Lüneburg Deutschland
  • Telefon: +49 4131 8901-0
  • Telefax: +49 4131 83200
  • E-Mail: service@clage.de
  • Internet: www.clage.de

Subject to technical changes, design changes and errors.

9120-91870 07.17

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals