caso DESIGN FW2000 Mincer Instruction Manual

Original Operating Manual
Mincer FW2000

Operating Manual

1.1 General
Please read the information contained herein so that you can become familiar with your device quickly and take advantage of the full scope of its functions.
Your mincer FW2000 will serve you for many years if you handle it and care for it properly.
We wish you a lot of pleasure in using it!
1.2 Information on this manual
These Operating Instructions are a component of the Mincer FW2000 (referred to hereafter as the device) and provide you with important information for the initial commissioning, safety, intended use and care of the device. The Operating Instructions must be available at all times at the device. This Operating Manual must be read and applied by every person who is instructed to work with the device:

• Commissioning
• Operation
• Troubleshooting and/or
• Cleaning
• Keep the Operating

Manual in a safe place and pass it on to the subsequent owner along with the device.
1.3 Warning notices
The following warning notices are used in the Operating Manual concerned here.
DANGER
A warning notice of this level of danger indicates a potentially dangerous situation.
If the dangerous situation is not avoided, this can lead to death or serious injuries.
► Observe the instructions in this warning notice in order to avoid the danger of death or serious personal injuries.
WARNING
A warning notice of this level of danger indicates a possible dangerous situation.
If the dangerous situation is not avoided, this can lead to serious injuries.
► Observe the instructions in this warning notice in order to avoid the personal injuries.
ATTENTION
A warning notice of this level of danger indicates a possible dangerous situation.
If the dangerous situation is not avoided, this can lead to slight or moderate injuries.
► Observe the instructions in this warning notice in order to avoid the personal injuries.
PLEASE NOTE
A notice of this kind indicates additional information, which will simplify the handling of the machine.

Safety

2.1 Intended use
This device is only intended for use in households in enclosed spaces for

• preparation of minced meat and tartare,
• preparation of sausages,
• processing of dough for example for spritz biscuit

Uses for a different purpose or for a purpose which exceeds this description are considered incompatible with the intended or designated use.
Warning
Danger due to unintended use! Dangers can emanate from the device if it is used for an unintended use and/or a different kind of use.
► Use the device exclusively for its intended use.
► Observe the procedural methods described in this Operating Manual.
Claims of all kinds due to damages resulting from unintended uses are excluded. The User bears the sole risk.
2.2 General Safety information
Please note
Please observe the following general safety notices with regard to the safe handling of the device.
Read the instructions for use carefully and look at the illustrations before using the device.
► Examine the device for any visible external damages prior to using it. Never put a damaged device into operation.
► If the power cable or plug are damaged, then they must be replaced by the manufacturer or its service agent in order to avoid a hazard.
► This device can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
Please note
► Children shall not use this device. Keep the device and its cord out of reach of children
► Children shall not play with the appliance.
► Cleaning and user maintenance shall not be made by children.
► Do not leave the device unsupervised when it is in operation.
► Only customer service departments authorized by the manufacturer may carry out repairs on the device, as otherwise the guarantee entitlements will be null and void in the event of any subsequent damages. Improperly performed repairs can cause considerable dangers for the user.
► Defective components must always be replaced with original replacement parts. Only such parts will guarantee that the safety requirements are fulfilled.
► Use only the supplied accessories. The warranty of the unit expires if you use accessory from other manufacturers.
► Carefully clean all components that will come in contact with food before first use.
► Unplug the device immediately after use.
► Do not process bones, nuts or other hard ingredients.
► Process sinew less, boneless and fatless meat in pieces.
► Use the device continuously for a maximum of 5 minutes.
Then let the device coold down for 10 minutes.
► Turn switch to REV if the unit is blocked. The snake rotates backwards. The meat is loosened to resolve the blockage.
► Never immerse the device, cord or plug in water or other liquids and do not place in the dishwasher.
► Do not overload the device and do not let it operate unloaded.
► Be sure the parts are properly assembled to original base and in place.
► Do not use appliance for other than intended household use.
► Device is not intended to be operated by means of an external timer or separate remote-control system.
2.3 Danger of injury
**Warning
Careless use of the appliance may result in injury.
Observe the following warnings to to avoid injury
► Never reach into the head tube always use the pusher.
► Never use your finger os tools to push ingredients deeper into the head tube while the device is running. Always use the pusher for this purpose.
► Pull the power plug and wait until moving prate have stopped running before you remove parts from device.
► Pull the power plug when the device is unsupervised, before every cleaning and before you detach or install any parts.
► Never hold your face over the head tube with hopper plate when the motor is running. If you have overlooked hard components during the preparation of the ingredients, they and also pieces of meat can be thrown out. Warning: Danger of injury!
14.4 Dangers due to electrical power
Mortal danger due to electrical power!
Mortal danger exists when coming into contact with live wires or subassemblies! Observe the following safety notices to avoid dangers due to electrical power:
► Do not operate this device if it has a damaged cable or plug, if it is not working properly or if it has been damaged or dropped. If the power cable or plug are damaged, then they must be replaced by the manufacturer or its service agent in order to avoid a hazard.
► Do not open the housing on the device under any circumstances. There is a danger of an electrical shock if live connections are touched and the electrical or mechanical structure is altered. In addition, functional faults on the device can also occur.
2.5 Limitation of liability
** All the technical information, data and notices with regard to the installation, operation and care are completely up-to-date at the time of printing and are compiled to the best of our knowledge and belief, taking our past experience and findings into consideration.
No claims can be derived from the information provided, the illustrations or descriptions in this manual. The manufacturer does not assume any liability for damages arising as a result of the following:

• Non-observance of the manual
• Uses for non-intended purposes
• Improper repairs
• Technical alterations, modifications of the device
• Use of unauthorized spare parts

Modifications of the device are not recommended and are not covered by the guarantee.
All translations are carried out to the best of our knowledge. We do not assume any liability for translation errors, not even if the translation was carried out by us or on our instructions. The original German text remains solely binding.
2.6 Copyright protection
This document is copyright protected. Brackman GmbH reserves all the rights, including those for photomechanical reproduction, duplication and distribution using special processes (e.g. data processing, data carriers, data networks), even partially.
Subject to content and technical changes.

Commissioning

This chapter provides you with important safety notices during the initial commissioning of the device. Observe the following notices to avoid dangers and damages:
3.1 Safety information
Warning
► Packaging materials may not be used for playing. There is a danger of suffocation.
3.2 Delivery scope and transport inspection
As a rule, the FW2000 is delivered with the following components:

• pusher
• snake
• fixing ring
• dough accessory with pattern
• hopper plate
• blade
• sausage accessory
• motor unit
• 3 cutting plates (fine, medium, coarse)
• head tube
• operating instructions

Please note
► Examine the shipment for its completeness and for any visible damages.
► Immediately notify the carrier, the insurance and the supplier about any incomplete shipment or damages as a result of inadequate packaging or due to transportation.
3.3 Unpacking
To unpack the device, proceed as follows:

• Remove the device out of the carton and remove the packaging material.

3.4 Disposal of the packaging
The packaging protects the device against damages during transit. The packaging materials are selected in accordance with environmentally compatible and recycling-related points of view and can therefore be recycled. Returning the packaging back to the material loop saves raw materials and reduces the quantities of accumulated waste.
Take any packaging materials that are no longer required to “Green Dot” recycling collection points for disposal.
Please note
► If possible, keep the original packaging for the device for the duration of the guarantee period of the device, in order that the device can be re- packaged properly in the event of a guarantee claim.
3.5 Setup location requirements:
In order to ensure the safe and trouble-free operation of the device, the setup location must fulfil the following prerequisites:

• Place the device on a firm and even work surface.
• Do not use the device outdoors.
• The device is not intended to be installed in a wall or a built-in cupboard.
• The device requires adequate air circulation (minimum distance 15 cm).
• Do not set up the device in a hot, wet or extremely damp environment or near flammable material.
• The installation and assembly of this device in non-stationary setup locations (e.g. on ships) must be carried out by specialist companies / electricians, provided they guarantee the prerequisites for the safe use of this device.

3.6 Electrical connection
In order to ensure the safe and trouble-free operation of the device, the following instructions must be observed for the electrical connection:

• Before connecting the device, compare the connection data (voltage and frequency) on the rating plate with those of your electrical network. This data must agree in order that no damages occur in the device. If in doubt, ask your qualified electrician.
• The connection between the device and the electrical network may employ a 3 meter long (max.) extension cable with a cross-section of 1.5 mm². The use of multiple plugs or gangs is prohibited because of the danger of fire that is involved with this.
• Make sure that the power cable is undamaged and has not been installed under the ice maker or over hot or sharp surfaces.
• The electrical outlet must be protected by a 16A safety cut-out switch.
• The electrical safety of the device is only guaranteed if the device is connected to a properly installed protective conductor system. If in doubt, have the house installation checked over by a qualified electrician.
  The manufacturer cannot be made responsible for damages that are caused by a missing or damaged protective conductor.

Design and Function

In this chapter, you’ll find important information on the design and function of the device.
4.1 Overview

1 motor unit
2 switch (REV, OFF, 1, 2)
3 locking handle
4 tube inlet
5 pusher| 6 hopper plate
7 head tube
8 snake
9 blade
10 cutting plate medium (5mm)| 11 cutting plate coarse (8 mm)
12 fixing ring
13 sausage accessory
14 dough accessory with pattern
15 cutting plate fine (3 mm)
---|---|---

4.2 Assembling
a) Place the motor unit (1) on a table. The locking handle (3) at tube inlet (4) has to be in horizontal position.
Place the head tube (7) into the tube inlet (4).
b) Slide the locking handle (3) downwards to secure it.
c) Place the snake (8) with the thicker end first into the head tube (7).
d) Place the blade (9) on the snake (8).
e) Place the cutting plate (10, 11 or 15) on blade (9) and snake (8)
f) Place the fixing ring (12) and tithe it with your hand.
g) Place the hopper plate (6) as seen on illustration on the head tube (7).
Do not block the air passage at the bottom.
4.3 Rating plate
The rating plate with the connection and performance data can be founded beneath the device.

Operation and Handing

This chapter provides you with important notices with regard to operating the device.
Observe the following notices to avoid dangers and damages:
Warning
► Do not leave the device unsupervised when it is in operation, so that you can intervene quickly in the event of dangers.
Please note
► Cool the head tube (7) overusing oft he device in the refrigerator or rinse it with cold water, this will improve the processing.
5.1 Before first use
Clean the device, see “cleaning“.
5.2 Operation of the mincer
Prepare the meat to pieces. Remove all bones, gristle, sinews. Do not use frozen meat.
Let frozen meat thaw completely. Enter the meat in the fillilng bowl. Slide the meat gently with the pusher into the head tube. If you want to produce tartare, you should  mince the meat 2 times by using the medium cutting place.
5.3 Making sausage

h) You need the sausage accessory (13). Place the snake (8) as usual with the thicker end first into the head tube (7). Insert the blade (9) with cutting plate (10, 11 or 15) on the snake (8). Then place the sausage accessory (13) on blade (9) and cutting plate (10, 11 or 15). Tightens the fixing ring (12). Enter your already minces and spices filling for the sausages on hopper plate (6)and push in gently with pusher (5) into the head tube (7). Soak the sausage skin in water for at least 10 minutes before you fill them. Clutch the sausage skin of the sausage accessory (13) and use the device as usual. If sauced skin gets stuck onto sausage accessory (13) then wet it with some water.
5.4 Processing dough for example spritz biscuit
You need the dough accessory (14). Place the snake (8) as usual with the thicker end first into the head tube (7). Insert the blade (9) and cutting plate (10, 11 or 15) on the snake.
i) Place the dough accessory (14) on blade (9) and cutting plate (10 or 11). Tighten the fixing ring (12)
j) Slide the pattern for spritz biscuit through the dough accessory.
k) Place the hopper plate (6) as usual on head tube (7) and use the pusher (5) to push the dough in the feed tube.

Cleaning and Maintenance

This chapter provides you with important notices with regard to cleaning and maintaining the device. Please observe the notices to prevent damages due to cleaning the device incorrectly and to ensure trouble-free operation.
6.1 Safety information
Attention
Please observe the safety instructions, before cleaning your device
► Unplug the device when not in use and before any cleaning.
► The motor unit with power cord (1), the snake (8), the head tube (7), the fixing ring (12) and the hopper plate (6) should not be placed in the dishwasher.
► The blade (9) is really sharp. Handle it with care.
6.2 Cleaning
Remove meat and dough residues from the head tube by mincing a piece of bread.
Turn of the power and unplug the power cord.
Roove the pusher (5) and hopper plate (6).
l) Loosen the fixing ring (12) and remove all parts out of head tube (7)
m) Turn the locking handle (3) to horizontal position and remove the head tube (7) from tube inlet (4).
Wash all parts that were in contact with food in hot soapy water. Clean all parts immediately after use. Clean the parts with hot water and dry them immediately after use.
You can clean the pusher (5), blade (9), cutting plates (10, 11, 15), sausage accessory (13) and dough accessory with patter (14) in the dishwasher. Lubricate the blade and cutting plate with vegetable oil.

WARNING Warning the blade is sharp. Danger of injury
Please note
► Please take care that the small parts does not disappear in the dishwasher.

Troubleshooting

This chapter provides you with important notices with regard to operating the device.
Observe the following notices to avoid dangers and damages:
7.1 Security advices
Attention
► Repairs of electrical appliances must be carried out by qualified personnel who are trained by the manufacturer.
► Repairs performed by untrained persons may result in considerable hazards for the user and damage the machine.
7.2 Troubleshooting

plugged.
• Please check whether the assembly is done according to assembly methods.
The device is blocked| • Turn the switch to REV to loosen the blockage. If this is not enough please switch of the device, unplug the cord and dissemble the device to remove the blockage.
The device stoped.| • The device is overheated. Switch of the device, unplug the cord. Dissemble the device and remove all ingredients from the device. Let it cool down for 60 minutes.
• Contact customer service if overheating system is activated too often.

Please note
► If above mentioned steps don’t solve the problem, please contact your customer service.
► Clean the device before you send it to customer service.

Disposal of the Old Device

Old electric and electronic devices frequently still contain valuable materials.
However, they also contain damaging substances, which were necessary for their functionality and safety. If these were put in the non-recyclable waste or were handled incorrectly, they could be detrimental to human health and the environment. Therefore, do not put your old device into the non-recyclable waste under any circumstances.
Please note
► Utilize the collection point, established in your town, to return and recycle old electric and electronic devices. If necessary, contact your town hall, local refuse collection service or your dealer for information.
► Ensure that your old device is stored safely away from children until it is taken away.

Guarantee

We provide a 24-month guarantee for defects caused by production or material faults, beginning on the date of purchase. Our guarantee is valid for Germany, Austria and the Netherlands. For all other countries, please contact us.
Your legal guarantee claims as per Art. 437 ff. German Civil Code (BGB) will remain unaffected by this. You may exercise your statutory guarantee rights free of charge. The guarantee does not cover damage caused by improper handling or use of the product or defects which have only a minor impact on the product’s functionality or value. In addition to this, the guarantee also excludes parts which are subject to wear and tear; transport damages insofar as we are not responsible for them and damages caused by repairs which were not carried out by us.
This product has been constructed for non-commercial use (domestic use) and its performance is designed to meet the corresponding needs. The guarantee only covers commercial use insofar as it is comparable to domestic use. The product is not intended for any other type of commercial use.
In the case of legitimate complaints we may either repair the defective product or replace it with a defect-free product at our discretion. Obvious defects must be notified to us within 14 days of the product’s delivery. Any further claims are excluded.
When making a guarantee claim please contact us before you return the product (always with the purchase receipt!). Our contact details (“Guarantor”) are provided at the beginning of this instruction manual.

Technical Data

References

• Domain Default page
• CASO Design Onlineshop

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>