Futaba 1M23Z03818 Telemetry Log Converter Ver1.10 Software User Guide

Futaba 1M23Z03818 Telemetry Log Converter Ver1.10 Software

By using this telemetry log converter software, the log file created with the transmitter corresponding to a telemetry log function is convertible for CSV.
The file of CSV can be opened by software, such as Microsoft Excel.

*Note: The Telemetry Log Converter software is for Windows® 11/10/8/7/By using this telemetry log converter software, the log file created with the transmitter corresponding to a telemetry log function is convertible for CSV.
The file of CSV can be opened by software, such as Microsoft Excel.

*Note: The Telemetry Log Converter software is for Windows® 11/10/8/7/Vista/XP use and is not compatible with other OS.

Distribution & exemption of liability

• Futaba Corporation shall not be responsible for any damage caused by use of this software. Use this software based on agreement to this.
• The copyright of this software and document resides with Futaba Corporation. Redistribution without the approval of the copyright holder is prohibited.
• Reverse engineering and modification of this software is strictly prohibited.
• No part of this manual may be reproduced in any form without prior permission.
• The contents of this manual are subject to change without prior notice.
•  While this manual has been carefully written, there may be inadvertent errors or omissions. Please contact our service center if you feel that any corrections or clarifications should be made.

Downloaded zip file extraction (decompression)

The downloaded Telemetry Log Converter software file is a Zip format file. Extract (decompress) this file, the procedure is shown as below.

• Download the Telemetry Log Converter

  1. Double click the Zip format file to display its contents.
  2. Click “Extract all files”. The Extraction Wizard launches.
  3.  Extract (decompress) the Zip format file to the same location as the Zip file storage location.

• Telemetry Log Converter.msi setup.exe

If a previous version of Telemetry Log Converter software is installed, uninstall the previous version and install the new version.

Telemetry Log Converter software installation

Before installing the Telemetry Log Converter software, confirm that all other applications are closed. Close all virus check and other resident programs, if any.

1. Double click the EXE file named “setup”, and push the “Next” button.
   

2. Choose the target folder, and push the “Next” button.
   

3. Push the “Next” button.
   

4. The install process begins.

5. The installer displays the following after the install process. Push the “Close” button.
   

How to use the Telemetry Log Converter Software

1. Telemetry log file is created with the transmitter corresponding to a telemetry log function. (Please read the manual of a transmitter about the creation method of a log file)

2. Telemetry log file is started.

3.  “Open” is pushed.

4. Telemetry data file (.FLD) is opened.
   

5. Choose a destination folder and input a filename.
   

6. Completion of conversion will display the next screen.

Converter File

(The contents of a converter file)

1. The record time of data
2. Each channel signal of a transmitter
3. Slot number
4. The type of sensor
5. Telemetry data

＜ The example of a conversion file ＞

1. The time of the data recorded
2. Each channel signal from the transmitter
3. Slot number
4. The type of sensor
5.  Telemetry data

Applicable Telemetry Sensor

Futaba

Telemetry Receiver| Receiver battery voltage|
---|---|---
Telemetry Receiver| EXT Receiver battery voltage|
SBS- 01T| Temperature sensor|
SBS- 01TE| Temperature sensor（for electric models）|
SBS- 01V| Voltage sensor|
SBS- 01RB| RPM sensor（for brushless motor）|
SBS- 01RO| RPM sensor（Optical type）|
SBS- 01RM| RPM sensor（Magnet type）|
SBS- 01A| Altitude sensor|
SBS- 01G| GPS sensor|
SBS- 01S| S.BUS 2 servo sensor| V1.2 ～
SBS- 01C| Current sensor| V1.3 ～
SBS- 02A| Altitude sensor| V1.3 ～
SBS-01TAS| Airspeed sensor| V1.5 ～
SBS- 02G| GPS sensor| V1.6 ～
MC970CR| Motor controller| V1.6 ～
MC- 980H/A| Motor controller| V1.8 ～
MC- 9130H/A| Motor controller| V1.8 ～
MC- 9200H/A| Motor controller| V1.8 ～
SBS- 01ML| Flight controller| V1.10 ～

Other manufacturers

Robbe F1675|
---|---
Robbe F1712|
Robbe F1672|
Robbe F1678|
PowerBox| V1.2 ～
Jetcat| V1.2 ～
KONTRONIK Kosmik| V1.2 ～
ROXXY| V1.2 ～
Castle TL0| V1.4 ～
EM- 100| V1.5 ～ (EM-100 <ver 9.11> V1.9 ～ )
Hobbywing| V1.8 ～
Scorpion| V1.8 ～

Note

log off

• Log files are created in the “LOG” folder of the SD card. Two files with the same file name but different extensions are created. (Example: 00001234.FLI, 00001234.FLD)
• Extension FLI: Slot allocation information file
• Extension FLD: log data file
• When copying or moving log files, be sure to select both .FLI and .FLD files.
• Log files can be converted to CSV format with the telemetry log converter published on our website.

Altimeter

• Altimeter altitude data, GPS distance and altitude data are output based on the point when the log is started (0 m). If the transmitter preset position and the log start position are different, the transmitter display and the log data display will differ. If you log start immediately before takeoff, you can record the altitude and distance from the takeoff position.

RPM

• The RPM log data does not reflect the transmitter gear ratio, motor pole number or fin number setting. It is necessary to calculate the gear ratio, the number of motor poles, and the number of fins in the RPM data.

Unit

• Distances and speeds etc. are always recorded in metric regardless of unit setting of a transmitter.
• Temperatures are also recorded in degrees Celsius.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>