TELTONIKA FMM00A Advanced OBDII Tracker User Manual

: June 9, 2024
: teltonika

Table of Contents

TELTONIKA FMM00A Advanced OBDII Tracker
KNOW YOUR DEVICE
PINOUT
SET UP YOUR DEVICE
PC CONNECTION WINDOWS
HOW TO INSTALL USB DRIVERS (WINDOWS)
CONFIGURATION
QUICK SMS CONFIGURATION
- DEFAULT CONFIGURATION SETTINGS
MOUNTING RECOMMENDATIONS
LED INDICATIONS
BASIC CHARACTERISTICS
SAFETY INFORMATION
CERTIFICATION AND APPROVALS
WARRANTY
WARRANTY DISCLAIMER
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TELTONIKA FMM00A Advanced OBDII Tracker

KNOW YOUR DEVICE

$TELTONIKA-FMM00A-Advanced-OBDII-Tracker-fig- $1$$

PINOUT

$TELTONIKA-FMM00A-Advanced-OBDII-Tracker-fig- $16$$

SET UP YOUR DEVICE

HOW TO INSERT MICRO-SIM CARD AND CONNECT THE BATTERY

$TELTONIKA-FMM00A-Advanced-OBDII-Tracker-fig- $3$$

COVER REMOVAL
Gently remove the FMM00A cover using a plastic pry tool from both sides.
MICRO-SIM CARD INSERT
Insert the Micro-SIM card as shown with the PIN request disabled or read our Wiki1 on how to enter it later in Teltonika Configurator2. Make sure that the Micro-SIM card cut-off corner is pointing forward to the slot.
wiki.teltonika-gps.com/view/FMM00A_Security_info
wiki.teltonika.lt/view/Teltonika_Configurator.
BATTERY CONNECTION
Connect the battery as shown to the device. Position the battery in a place where it does not obstruct other components.
ATTACHING COVER BACK
Attach the device cover back. The device is ready to be connected.

PC CONNECTION WINDOWS

Power-up FMM00A with DC voltage (10 – 30 V) power supply using the supplied power cable. LEDs should start blinking, see “LED indications1”.
Connect device to the computer using a Micro-USB cable or Bluetooth connection:
- Using Micro-USB cable
- You will need to install USB drivers, see “How to install USB drivers (Windows)2”
- Using Bluetooth
- FMC00A Bluetooth is enabled by default. Turn on Bluetooth on your PC, then select Add Bluetooth or another device Bluetooth. Choose your device named – “FMM00A_last_7_imei_digits”, without LE in the end. Enter default password 5555, press Connect and then select Done.
You are now ready to use the device on your computer.
wiki.teltonika-gps.com/view/FMM00A_LED_status
“How to install USB drivers”

HOW TO INSTALL USB DRIVERS (WINDOWS)

Please download COM port drivers from here1.
Extract and run TeltonikaCOMDriver.exe.
Click Next in the driver installation window.
In the following window click the Install button.
Setup will continue installing the driver and eventually, the confirmation window will appear. Click Finish to complete the setup.

CONFIGURATION

At first FMM00A device will have default factory settings set. These settings should be changed according to the user’s needs. The main configuration can be performed via Teltonika Configurator1 software. Get the latest Configurator version from here2. Configurator operates on Microsoft Windows OS and uses the prerequisite MS .NET Framework. Make sure you have the correct version installed.

wiki.teltonika-gps.com/view/Teltonika_Configurator
wiki.teltonika-gps.com/view/Teltonika_Configurator_versions.

MS .Net requirements

$TELTONIKA-FMM00A-Advanced-OBDII-Tracker-fig- $17$$

www.microsoft.com.
dotnet.microsoft.com/en-us/download/dotnet- framework/net462.

The downloaded Configurator will be in a compressed archive. Extract it and launch Configurator.exe. After launch software language can be changed by clicking in the right bottom corner.

The configuration process begins by pressing on the connected device.

After connection to Configurator Status window will be displayed.

Various Status window1 tabs display information about GNSS2, GSM3, I/O4, Maintenance5 and etc. FMM00A has one user-editable profile, which can be loaded and saved to the device. After any modification of configuration, the changes need to be saved to the device using Save to Device button. Main buttons offer the following functionality:

Load from the device – loads configuration from the device.
Save to device – saves the configuration to the device.
Load from file – loads configuration from file.
Save to file – saves the configuration to file.
Update firmware – updates the firmware on the device.
Read records – reads records from the device.
Reboot the device – restart the device.
Reset configuration – sets device configuration to default.

The most important configurator section is GPRS – where all your server and GPRS settings6 can be configured and Data Acquisition7 – where data acquiring parameters can be configured. More details about FMM00A configuration using Configurator can be found in our Wiki8.

QUICK SMS CONFIGURATION

The default configuration has optimal parameters present to ensure the best performance of track quality and data usage. Quickly set up your device by sending this SMS command to it: $TELTONIKA-FMM00A-Advanced-OBDII-Tracker-fig- $8$$

Note: Before SMS text, two space symbols should be inserted.

GPRS SETTINGS:

2001 – APN
2002 – APN username (if there are no APN usernames, an empty field should be left)
2003 – APN password (if there are no APN passwords, an empty field should be left)
SERVER SETTINGS:
2004 – Domain
2005 – Port
2006 – Data sending protocol (0 – TCP, 1 – UDP)

DEFAULT CONFIGURATION SETTINGS

$TELTONIKA-FMM00A-Advanced-OBDII-Tracker-fig- $10$$

After successful SMS configuration, the FMM00A device will synchronize time and update records to configured server. Time intervals and default I/O elements can be changed by using Teltonika Configurator1 or SMS parameters2.

MOUNTING RECOMMENDATIONS

CONNECTING THE DEVICE TO THE VEHICLE:
Find the OBDII connector in your vehicle.

Most common OBDII connector locations.

LED INDICATIONS

NAVIGATION LED INDICATIONS

Behavior/Meaning

Permanently
switched on GNSS signal is not received
Blinking every
second Normal mode, GNSS is working
Off
- GNSS is turned off because:
- The device is not working or the Device is in sleep mode
Blinking fast
constantly Device firmware is flashed

STATUS LED INDICATIONS

Behavior/Meaning

Blinking every second in Normal mode
Blinking every two seconds Sleep mode
Blinking fast for a short time Modem activity
Off Device is not working or the Device is in boot mode

BASIC CHARACTERISTICS

Module

Name Quectel BG95-M1, Teltonika TM2500
Technology LTE CAT M1/GNSS/BLUETOOTH

GNSS

GNSS GPS, GLONASS, GALILEO, BEIDOU, SBAS, QZSS, DGPS, AGPS
Receiver 33 channel
Tracking sensitivity -165 dBM
Accuracy < 3 m
Hot start < 1 s
Warm start < 25 s
Cold start < 35 s

Cellular

Technology LTE CAT M1

4G bands

LTE-FDD (CAT M1):
B1/B2/B3/B4/B5/B8/B12/B13/B18/ B19/B20/B25/B26/B27/B28/B66/B85
Data transfer
- BG95:
  LTE: Max. 588Kbps (DL)/Max.1119Kbps (UL)
Transmit power Class 5 for LTE-FDD: 20±2dBm
Data support SMS (text/data)

Power

Input voltage range 10 – 30 V DC with overvoltage protection
Back-up battery 115 mAh Li-Po battery 3.7 V (0.43 Wh)
Internal fuse 3A, 125V

Power Consumption

At 12V < 6.5 mA (Ultra Deep Sleep)
At 12V < 8 mA (Deep Sleep)
At 12V < 13 mA (Online Deep Sleep)
At 12V < 16.3 mA (GPS Sleep)
At 12V < 31 mA (nominal with no load)
At 12V < 0.25A Max. (with full Load/Peak

Bluetooth

Specification 4.0 + LE
Supported peripherals Temperature and Humidity sensor1, Inateck Barcode Scanner, Universal BLE sensors support

OBD Interface

Data K-Line, CAN Bus data
Data reading
Up to 32 vehicle onboard parameters, 9 supported OBD protocols

Interface

Connection OBDII socket
GNSS antenna Internal High Gain
GSM antenna Internal High Gain
USB 2.0 Micro-USB
LED indication 2 status LED lights
SIM Micro-SIM
Memory 128MB internal flash memory

Physical Specification

Dimensions 67,2 x 49,6 x 25 mm (L x W x H)
Weight 63 g

Operating Environment

Operating temperature (without battery) -40 °C to +85 °C
Storage temperature (without battery) -40 °C to +85 °C
Operating humidity 5% to 95% non-condensing
Operating temperature (with battery)
- 0 °C to +45 °C
Storage temperature (with battery)
- -20 °C to +45 °C for 1 month
- -20 °C to +35 °C for 6 months
Ingress Protection Rating IP41
Battery charge temperature 0 °C to +45 °C
Battery discharge temperature -20 °C to +60 °C
Battery storage temperature
- -20 °C to +45 °C for 1 month
- -20 °C to +35 °C for 6 months

Features

Sensors Accelerometer
Scenarios
- Green Driving, Over Speeding detection, Jamming detection, GNSS Fuel Counter, Excessive Idling detection, Unplug detection, Towing detection, Crash detection, Auto Geofence, Manual Geofence, Trip2
Sleep modes
- GPS Sleep, Online Deep Sleep, Deep Sleep, Ultra Deep Sleep3
Configuration and firmware update
FOTA Web4, FOTA5, Teltonika Configurator6 (USB, Bluetooth), FMBT mobile application (Configuration)
SMS Configuration, Events, Debug
GPRS commands Configuration, Debug
Time Synchronization GPS, NITZ, NTP
Fuel monitoring OBDII
Ignition detection Accelerometer, External Power Voltage, Engine RPM

SAFETY INFORMATION

This message contains information on how to operate FMM00A safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!

The device uses SELV limited power source. The nominal voltage is +12 V DC. The allowed voltage range is +10…+30 V DC.
To avoid mechanical damage, it is advised to transport the device in an impact-proof package. Before usage, the device should be placed so that its LED indicators are visible. They show the status of device’s operation.
Before unmounting the device from the vehicle, the ignition MUST be OFF. $TELTONIKA-FMM00A-Advanced-OBDII-Tracker-fig- $12$$

CERTIFICATION AND APPROVALS

This sign on the package means that it is necessary to read the User‘s Manual before your start using the device. Full User‘s Manual version can be found in our Wiki1.
1. wiki.teltonika-gps.com/index.php?title=FMM00A
This sign on the package means that all used electronic and electric equipment should not be mixed with general household waste.
The RoHS1 is a directive regulating the manufacture, import, and distribution of Electronics and Electrical Equipment (EEE) within the EU, which bans from using 10 different hazardous materials (to date).
- wiki.teltonika-gps.com/view/FMM00A_RoHS.

FCC ID: 2A3HUFMM00A.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/ TV technician for help.
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To comply with FCC RF Exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for the transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

IC NOTICE
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

this device may not cause interference, and
this device must accept any interference, including interference that may cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES-003.

IC: 28804-FMM00A.
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. To comply with RSS-102 RF Exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for the transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

CHECK ALL CERTIFICATES
All newest certificates may be found in our Wiki2.

wiki.teltonika-gps.com/view/FMM00ACertification%26_Approvals.

WARRANTY

TELTONIKA guarantees its products to be free of any manufacturing defects for a period of 24 months. With additional agreement we can agree on a different warranty period, for more detailed information please contact our sales manager.

Contact usteltonika-gps.com/about-us/contacts
All batteries carry a reduced 6-month warranty period.

If a product should fail within this specific warranty time, the product can be:

Repaired
Replaced with a new product
Replaced with an equivalent repaired product fulfilling the same functionality
TELTONIKA can also repair products that are out of warranty at an agreed cost.

WARRANTY DISCLAIMER

TELTONIKA PRODUCTS ARE INTENDED TO BE USED BY PERSONS WITH TRAINING AND EXPERIENCE. ANY OTHER USE RENDERS THE LIMITED WARRANTIES EXPRESSED HEREIN AND ALL IMPLIED WARRANTIES NULL AND VOID AND THE SAME ARE HEREBY EXCLUDED. ALSO EXCLUDED FROM THIS LIMITED WARRANTY ARE ANY AND ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO, LOSS OF USE OR REVENUE, LOSS OF TIME, INCONVENIENCE, OR ANY OTHER ECONOMIC LOSS.

More information can be found at teltonika-gps.com/warranty-repair.