Whirlpool W11625829B Bottom Mount Fridge Owner’s Manual

Whirlpool W11625829B Bottom Mount Fridge

Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean:

DANGER
You can be killed or seriously injured if you don’t immediately follow instructions.

WARNING
You can be killed or seriously injured if you don’t follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING:
To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following:

• Children should be supervised to ensure that they do not play with the appliance.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Do not use an extension cord.
• If power supply cord is damaged, it must be replaced by the manufacturer, its service agent, or a similarly qualified person in order to avoid a hazard.
• Connect to potable water supply only.
• This appliance is intended to be used in household and similar applications such as: staff kitchen areas in shops, offices, and other working environments; farm houses and by clients in hotels, motels, and other residential-type environments; bed and breakfast-type environments; and catering and similar non-retail applications.
• Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
• Do not use replacement parts that have not been recommended by the manufacturer (e.g., parts made at home using a 3D printer).
• Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.
• Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
• Do not damage the refrigerant circuit.
• Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.
• Ice maker kit can be added to some models. See serial tag inside the food compartment of appliance for ice maker kit model information.
• A qualified service technician must install the water line and ice maker. See installation instructions supplied with ice maker kit for complete details.

SAVE THESE INSTRUCTIONS

Proper Disposal of Your Old Refrigerator

WARNING:
Risk of child entrapment. Before you throw away your old refrigerator or freezer:

• Take off the doors.
• Leave the shelves in place so that children may not easily climb inside.

WARNING

Suffocation Hazard
Remove doors or lid from your old appliance. Failure to do so can result in death or brain damage.

IMPORTANT:
Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous, even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.

Important information to know about disposal of refrigerants:
Dispose of refrigerator in accordance with federal and local regulations. Refrigerants must be evacuated by a licensed, EPA-certified refrigerant technician in accordance with established procedures.

MAINTENANCE AND CARE

Cleaning

WARNING

Explosion Hazard

• Risk of Fire or Explosion.
• Flammable Refrigerant Used.
• Do Not Use Mechanical Devices to Defrost Refrigerator.
• Do Not Puncture Refrigerant Tubing.

Both the refrigerator and freezer sections defrost automatically. However, clean both sections about once a month to avoid odor buildup. Wipe up spills immediately.

IMPORTANT:

• Because air circulates between both sections, any odors formed in one section will transfer to the other. You must thoroughly clean both sections to eliminate odors. To avoid odor transfer and drying out of food, wrap or cover foods tightly.
• For stainless steel models, stainless steel is corrosion-resistant and not corrosion-proof. To help avoid corrosion of your stainless steel, keep your surfaces clean by using the following cleaning instructions.

To Clean Your Refrigerator:

NOTE:
Do not use abrasive or harsh cleaners such as window sprays, scouring cleansers, flammable fluids, muriatic acid, cleaning waxes, concentrated detergents, bleaches, or cleansers containing petroleum products on exterior surfaces (doors and cabinet), plastic parts, interior, and door liners or gaskets. Do not use paper towels, scouring pads, or other harsh cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand-wash, rinse, and dry removable parts and interior surfaces thoroughly. Use a clean sponge or soft cloth and a mild detergent in warm water.

3. Clean the exterior surfaces.
   Painted metal: Wash painted metal exteriors with a clean, soft cloth or sponge and a mild detergent in warm water. Rinse surfaces with clean, warm water and dry immediately to avoid water spots.
   Stainless steel: Wash stainless steel surfaces with a clean, soft cloth or sponge and a mild detergent in warm water. Rinse surfaces with clean, warm water and dry immediately to avoid water spots.
   NOTE: When cleaning stainless steel, always wipe with the grain to avoid cross-grain scratching.
   WARNING
   Explosion Hazard
   

   • Risk of Fire or Explosion due to Puncture of Refrigerant Tubing;
   • Follow Handling Instructions Carefully.
   • Flammable Refrigerant Used.

4. There is no need for routine condenser cleaning in normal home operating environments. If the environment is particularly greasy or dusty, or there is a significant pet traffic in the home, the condenser should be cleaned every 2 to 3 months to ensure maximum efficiency.
   If you need to clean the condenser:

5. Pull the refrigerator out away from the wall. See “Unpack the Refrigerator.”

6. Remove the base grille.

7. Vacuum coils when they are dusty or dirty.

8. Replace the base grille when finished.

9. Roll the refrigerator back into place. Make sure to leave 1″ (2.5 cm) between the cabinet back and the wall.

10. Check to see that the refrigerator is level.

11. Plug in the refrigerator or reconnect power.

Changing the LED Module

IMPORTANT:
The lights in both the refrigerator and freezer compartments use LED technology that do not need to be replaced. If an LED module(s) do not illuminate when the refrigerator and/or freezer door is opened, call for assistance or service. See “Quick Start Guide” for contact information.

Water Filtration System
Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

IMPORTANT:
The disposable water filter should be replaced at least every 6 months. If the water flow to the water dispenser or ice maker decreases noticeably before 6 months have passed, replace the water filter more often.

Install the Water Filter
To order a replacement filter, contact us at www.whirlpool.com/Parts & Accessories. See the “Quick Start Guide” for details.

NOTE:
If the filter is not installed correctly, water may dispense at a lower flow rate and there will be slower ice production. Improper filter installation may also cause the water filter housing to leak.

Right-Hand Side of Refrigerator Ceiling

1. Locate the accessory packet in the refrigerator and remove the water filter.

2. Take the water filter out of its packaging and remove the cover from the O-rings. Be sure the O-rings are still in place after the cover is removed.

3. The water filter compartment is located in the right-hand side of the refrigerator ceiling. Push latch on the filter door to release the catch, then lower the door.

4. Align the arrow on the water filter label with the cutout notch in the filter housing and insert the filter into the housing.

5. Turn the filter knob clockwise 180 degrees (1/2 turn), until it locks into the housing.
   NOTE: If the filter is not correctly locked into the housing, the water dispenser will not operate. Water will not flow from the dispenser.

6. While the compartment door is still open, lift the filter up into the compartment. Then, close the filter compartment door completely.

7. Flush the water system. See “Flush the Water System” for details.
   IMPORTANT: If you do not flush the water system, you may experience dripping and/or decreased flow from the water dispenser.

Flush the Water System
Air in the water dispensing system can cause the water dispenser to drip. After connecting the refrigerator to a water source or replacing the water filter, flush the water system. Flushing the water dispensing system forces air from the water line and filter and prepares the water filter for use. Additional flushing may be required in some households.

NOTE: As air is cleared from the system, water may spurt out of the dispenser.

1. Using a sturdy container, depress and hold the water dispenser paddle for 5 seconds.
2. Release the dispenser paddle for 5 seconds. Repeat steps 1 and 2 until water begins to flow.
3. Once water begins to flow, continue depressing and releasing the dispenser pad (5 seconds on, 5 seconds off) until a total of 1 gallon (3.8 L) has been dispensed.

Replacing the Water Filter
To purchase a replacement water filter, use model number Filter A, contact your dealer, or call 1-800-422-9991 in the U.S.A. or 1-800-807-6777 in Canada. Replacement filter part number and filter model names can be found on the Performance Data Sheet page.

IMPORTANT:
Air trapped in the water system may cause water and filter to eject. Always dispense water for at least 2 minutes before removing the filter or blue bypass cap.

1. If applicable, press upward on the water filter cover to access the filter.
2. Turn filter counterclockwise, and pull straight out to remove. NOTE: There may be some water in the filter. Some spilling may occur. Use a towel to wipe up any spills.
3. Remove sealing label from the replacement filter and insert the filter end into the filter head.
4. Turn the filter clockwise until it stops. Snap the filter cover closed.
5. Flush the water system. See “Flush the Water System” for details.

NOTE:
The dispenser feature may be used without a water filter installed. Your water will not be filtered. If this option is chosen, replace the filter with the blue bypass cap.

Reset Water Filter Status
After replacing the water filter, press and hold Reset Filter or Filter Reset (depending on your model) for 3 seconds. The Order and Replace indicator lights will blink and then go off when the system is reset. On some models the indicator light will change to blue when the system is reset. See the “Quick Start Guide” for more information.

On models with Options and Measured Fill buttons located on the control panel:
After changing the water filter, reset the status light. Press the Options button to enter Options mode, then press Lock to initiate the reset, then press Measured Fill to confirm that you want to reset the status light. When the system is reset, the “Order” and “Replace” icons will disappear from the display screen.

On models with Water Filter button located on the control panel:
After changing the water filter, reset the status. Press and hold the Water Filter button for 3 seconds. When the system is reset, the water filter icon will return to Blue and the words “Replace Filter” will disappear from the display.

Vacation and Moving Care

Vacations
If You Choose to Leave the Refrigerator On While You’re Away:

1. Use up any perishables and freezer other items.
2. If your refrigerator has an automatic ice maker, and is connected to the household water supply, turn off the water supply to the refrigerator. Property damage can occur if the water supply is not turned off.
3. If you have an automatic ice maker, turn off the ice maker.

NOTE:
Raise the wire shutoff arm to Off (arm up) position. 4. Empty the ice bin.

If You Choose to Turn Off the Refrigerator Before You Leave:

1. Remove all food from the refrigerator.
2. If your refrigerator has an automatic ice maker:
   • Turn off the water supply to the ice maker at least one day ahead of time.
   • When the last load of ice drops, raise the wire shutoff arm to the Off (up) position.
3. Empty the ice bin.
4. Turn off the Temperature control(s). See “Using the Controls” in the Quick Start Guide.
5. Clean the refrigerator, wipe it, and dry it well.
6. Tape rubber or wood blocks to the tops of both doors to prop them open far enough for air to get in. This stops odor and mold from building up.

Moving
When you are moving your refrigerator to a new home, follow these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:
   • Turn off the water supply to the ice maker at least one day ahead of time.
   • Disconnect the water line from the back of the refrigerator.
   • When the last load of ice drops, raise the wire shutoff arm to the Off (up) position.
2. Remove all food from the refrigerator and pack all frozen food in dry ice.
3. Empty the ice bin.
4. Turn off the Temperature control(s). See “Using the Controls” in the Quick Start Guide.
5. Unplug refrigerator.
6. Clean, wipe, and dry thoroughly.
7. Take out all removable parts, wrap them well, and tape them together so they don’t shift and rattle during the move.
8. Depending on the model, raise the front of the refrigerator so it rolls more easily or raise the leveling screws so they don’t scrape the floor. See online “Adjust the Door(s)” or “Door Closing and Door Alignment.”
9. Tape the doors closed and tape the power cord to the back of the refrigerator.

When you get to your new home, put everything back and refer to “Installation Instructions” for preparation instructions. If your refrigerator has an automatic ice maker, remember to reconnect the water supply to the refrigerator.

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

WARNING

Excessive Weight Hazard

• Use two or more people to move and install or uninstall the appliance.
• Failure to do so can result in back or another injury.

Remove the Packaging

• Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.
• Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information, see “Refrigerator Safety.”
• Dispose of/recycle all packaging materials.

When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to cover the floor with cardboard or hardboard to avoid floor damage. Always pull the refrigerator straight out when moving it. Do not wiggle or “walk” the refrigerator when trying to move it, as floor damage could occur.

Clean Before Using
After you remove all of the packaging materials, clean the inside of your refrigerator before using it. See the cleaning instructions in the “Maintenance and Care” section of your Owner’s Manual.

Important information to know about glass shelves and covers:
Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

Electrical Requirements

WARNING

Electrical Shock Hazard

• Plug into a grounded 3-prong outlet.
• Do not remove the ground prong.
• Do not use an adapter.
• Do not use an extension cord.
• Failure to follow these instructions can result in death, fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person. Do not use a cord that shows cracks or abrasion damage along its length or at either the plug or connector end.

Recommended Grounding Method
A 115 V, 60 Hz, AC-only 15 A or 20 A fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator and approved accessories be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

NOTE:
Before performing any type of installation, cleaning, or removing a light bulb, turn the refrigerator to OFF. Depending on your model, turn the refrigerator control to the word OFF, or press the refrigerator down arrow touch pad until a dash (–) appears in refrigerator displays as shown. Disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and reset the temperature controls to the desired setting. See “Quick Start Guide.”

Location Requirements

WARNING

Explosion Hazard

• Keep flammable materials and vapors, such as gasoline, away from appliance.
• Use nonflammable cleaner.
• Failure to do so can result in death, explosion, or fire.

IMPORTANT:
This refrigerator is designed for indoor, household use only.

This appliance is intended to be used in a household and similar applications such as:

• Staff kitchen areas in shops, offices and other working environments.
• Farm houses and by clients in hotels, motels and other residential-type environments.
• Bed and breakfast type environments.
• Catering and similar non-retail applications.

To ensure proper ventilation for your refrigerator, allow for 1/2″ (1.25 cm) of space on each side and at the top. Allow for 1″ (2.54 cm) of space behind the refrigerator. If your refrigerator has an ice maker, allow extra space at the back for the water line connections. When installing your refrigerator next to a fixed wall, leave 2 1/2″ (6.3 cm) minimum on the hinge side (some models require more) to allow for the door to swing open.

NOTE:
This refrigerator is intended for use in a location where the temperature ranges from a minimum of 55°F (13°C) to a maximum of 110°F (43°C). The preferred room temperature range for optimum performance, which reduces electricity usage and provides superior cooling, is between 60°F (15°C) and 90°F (32°C). It is recommended that you do not install the refrigerator near a heat source, such as an oven or radiator.

Water Supply Requirements
Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools Needed:

• Flat-blade screwdriver
• 7/16″ and 1/2″ Open-end or two adjustable wrenches
• 1/4″ Nut driver
• 1/4″ Drill bit
• Cordless drill

IMPORTANT:

• Connect to a potable water supply only.
  Do not use water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

• All installations must meet local plumbing code requirements.

• Do not use a piercing-type or 3/16 ” (4.76 mm) saddle valve which reduces water flow and clogs more easily.

• Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain above freezing.

• For models with water filters, the disposable water filter should be replaced at least every 6 months.

Water Pressure
A cold water supply with water pressure of between 35 psi and 120 psi (241 kPa and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT:
The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 35 psi and 120 psi (241 kPa and 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 psi to 60 psi (276 kPa to 414 kPa). If the water pressure to the reverse osmosis system is less than 40 psi to 60 psi (276 kPa to 414 kPa):

IMPORTANT:
Flush the water system before calibrating Measured Fill. See “Flush the Water System” in the Owner’s Manual. If you have questions about your water pressure, call a licensed, qualified plumber.

Connect the Water Supply
Read all directions before you begin.

IMPORTANT:

• Plumbing shall be installed in accordance with the International Plumbing Code and any local codes and ordinances.
• The water tubing on the back of the refrigerator (which is used to connect to the household water line) is a PEX (cross-linked polyethylene) tube. Copper and PEX tubing connections from the household water line to the refrigerator are acceptable and will help avoid off-taste or odor in your ice or water. Check for leaks. If PEX tubing is used instead of copper, we recommend contacting Service to obtain current part numbers.
• Install tubing only in areas where temperatures will remain above freezing.
• If you turn on the refrigerator before the water line is connected, turn off the ice maker to avoid excessive noise or damage to the water valve.

Connect to Water Line

1. Unplug the refrigerator or disconnect the power.
2. Turn off the main water supply. Turn on the nearest faucet long enough to clear the line of water.
3. Find a 1/2″ to 1 1/4″ (12.7 mm to 31.8 mm) vertical cold water pipe near the refrigerator.
4. Determine the length of copper tubing you need. Measure from the connection on the lower right rear of the refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4″ (6.35 mm) O.D. (outside diameter) copper or PEX tubing. Be sure both ends of copper or PEX tubing are cut square.
5. Using a cordless drill, drill a 1/4″ (6.35 mm) hole in the cold water pipe you have selected.
   • A. Cold water pipe
   • B. Pipe clamp
   • C. Copper or PEX tubing
   • D. Compression nut
   • E. Compression sleeve
   • F. Shutoff valve
   • G. Packing nut
6. Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the 1/4″ (6.35 mm) drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so the washer makes a watertight seal. Do not over-tighten.
7. Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw the compression nut onto the outlet end with an adjustable wrench. Do not overtighten or you may crush the copper tubing.
8. Place the free end of the tubing in a container or sink, and turn on the main water supply. Flush the tubing until the water is clear. Turn off the shutoff valve on the water pipe.

Connect to Refrigerator
Depending on your model, the water line may come down from the top or up from the bottom. Follow the connection instructions for your model.

Style 1

1. Remove the plastic cap from the water valve inlet port. Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not over-tighten. Confirm copper tubing is secure by pulling on copper tubing.
2. Create a service loop with copper tubing. Avoid kinks when coiling the tubing. Secure copper or PEX tubing to the refrigerator cabinet with a “P” clamp.
   • A. Copper or PEX tubing
   • B. “P” clamp
   • C. Compression nut
   • D. Compression sleeve
3. Turn on water supply to refrigerator and check for leaks. Correct any leaks.

Style 2

1. Create a service loop (minimum diameter of 2 ft [61 cm]) with the copper or PEX tubing. Avoid kinks when coiling the tubing.
2. Remove the plastic cap from water valve inlet port. Place a compression nut and sleeve on the copper or PEX tubing.
3. Insert the end of the copper or PEX tubing into the water valve inlet port. Shape tubing slightly so that the tubing feeds straight into the port to avoid kinks.
4. Slide the compression nut over the sleeve and screw into the water valve inlet port.
   • A. PEX water tubing
   • B. Sleeve
   • C. Compression nut
   • D. Copper or PEX tubing
5. Using an adjustable wrench, hold the nut on the plastic water line to keep it from moving. Then, with a second wrench turn the compression nut on the copper tubing counterclockwise to completely tighten. Do not overtighten.
   • A. “P” clamp
   • B. PEX water line
   • C. Compression nut
   • D. Copper tubing
6. Check the connection by pulling on tubing. Attach the PEX water line to the refrigerator cabinet with a “P” clamp.
7. Turn on water supply to the refrigerator and check for leaks. Correct any leaks.

Complete the Installation

WARNING

Electrical Shock Hazard

• Plug into a grounded 3 prong outlet.
• Do not remove ground prong.
• Do not use an adapter.
• Do not use an extension cord.
• Failure to follow these instructions can result in death, fire, or electrical shock.

1. Plug into a grounded 3–prong outlet.
   NOTE: Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely fill the ice storage bin.

2. Flush the water system. See “Flush the Water Systems.”

REFRIGERATOR FEATURES

Crisper Humidity Control
You can control the amount of humidity in the moisture-sealed crisper. Depending on your model, adjust the control to any setting between Fruit and Vegetables or Low and High.

• Fruit/Low (open) for best storage of fruits and vegetables with skins.
• Vegetables/High (closed) for best storage of fresh, leafy vegetables.

For information on additional features for your appliance, see online “Feature Guide.”

Ice Maker and Storage Bin (on some models)

Ice Production Rate

• Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced.
• Allow 3 days to completely fill the ice storage bin. The ice maker should produce approximately 3 lbs (1.4 kg) (8 to 12 batches) of ice in a 24-hour period.
• To increase ice production, lower the freezer and refrigerator temperature, or see “Control Panel Descriptions” in the Quick Start Guide for details. Wait 24 hours between adjustments.

Ice Maker in the Freezer

Turn the Ice Maker On/Off:
Turn the Ice Maker On/Off for Icemaker without a switch:

• To turn on the ice maker, simply lower the wire shutoff arm.
• To manually turn the ice maker off, lift the wire shutoff arm to the off (arm up) position and listen for the click.
• Your ice maker has an automatic shutoff. As ice is made, the ice cubes will fill the ice storage bin and the ice cubes will raise the wire shutoff arm to the off (arm up) position. Do not force the wire shut off the arm up or down.

For icemakers with a switch:
For icemakers with a switch, use the switch to turn ON or Off the ice maker .

NOTE:
Turn off the ice maker before removing the ice storage bin to serve ice or to clean the bin. This will keep the ice cubes from dropping out of the ice maker and into the freezer compartment. After replacing the ice storage bin, turn on the ice maker.

Wash the ice storage bin with mild soap and warm water. Slide the ice storage bin under the ice maker and push it toward the back as far as it will go.

DOOR AND HANDLE INSTRUCTIONS

Refrigerator Doors and Drawer
TOOLS NEEDED: 5/16″, 3/8″, 1/4″ hex head socket wrench, a Torx† T20 screwdriver, a #2 Phillips screwdriver, and a flat-blade screwdriver

IMPORTANT:

• Your refrigerator may have a standard reversible refrigerator door with either a freezer door or freezer drawer, or French doors. Follow the instructions specific to the door style of your model.

• If you only want to remove and replace the doors, see
  “Remove Doors and Hinges” and “Replace Doors and Hinges.”

• Before you begin, turn the refrigerator control Off, and remove food and adjustable door or utility bins from the doors.

Remove and Replace Door Handles

REFRIGERATOR DOOR HANDLES

Refrigerator Door Handle Style 1

• Using a 3/32″ or 1/8″ hex key, loosen the two set screws located on the side of each handle. Pull the handle straight out of the drawer. Make sure you keep the screws for reattaching the handles.
• To replace the handles, reverse the directions.

Refrigerator Door Handle Style 2

• Remove the screw cover.
• Remove the handle assembly. Keep all parts together.
• To replace the handles, reverse the directions.

Refrigerator Door Handle Style 3

• Using a 3/32″ or 1/8″ hex key, loosen the two setscrews located on the side of each handle. Pull the handle straight out from the drawer. Make sure you keep the screws for reattaching the handles.
• To replace the handles, reverse the directions.

Refrigerator Door Handle Style 4

• To remove the handle, remove the screw attaching the trim to the upper end of the handle. Using a flat-blade screwdriver wrapped in masking tape, pry the trim piece from the lower end of the handle. Then, remove the screws attaching the handle to the door.
• To replace handle, reverse directions.

Refrigerator Door Handle Style 5

• To remove the handle, grasp the lower part of the handle firmly, slide the handle up and pull the handle straight out from the door.
• To replace the handle, position the handle so that the large holes in the mounting clips are down and align the holes with the door studs. Rotate the handle so that the mounting clips are flat against the door and slide the handle down to engage.

FREEZER DOOR HANDLES

Freezer Door Handle Style 1

• Using a 3/32″ or 1/8″ hex key, loosen the two setscrews located on the side of each handle. Pull the handle straight out from the drawer. Make sure you keep the screws for reattaching the handles.
• To replace the handles, reverse the directions.

Freezer Door Handle Style 2

• Remove the screw cover.
• Remove the handle assembly. Keep all parts together.
• To replace the handles, reverse the directions.

Freezer Door Handle Style 3

• Remove screws and handle.
• To replace handle, reverse directions.

Freezer Door Handle Style 4

• Remove screws and handle.
• To replace the handles, reverse the directions.

Freezer Door Handle Style 5

• To remove the handle, grasp the lower part of the handle firmly, slide the handle up and pull the handle straight out from the door.
• To replace the handle, position the handle so that the large holes in the mounting clips are down and align the holes with the door studs. Rotate the handle so that the mounting clips are flat against the door and slide the handle down to engage.

Remove Doors and Hinges

STANDARD DOOR

Standard Door – Freezer drawer models

1. Unplug the refrigerator or disconnect the power

2. Keep the refrigerator door closed until you are ready to lift it free from the cabinet.
   NOTE: Provide additional support for the door while the hinges are being moved. Do not depend on the door gasket magnets to hold the door in place while you are working.

3. Remove the parts for the top hinge as shown below. Lift the refrigerator door free from the cabinet.

4. Remove the parts for the bottom hinge as shown below.

Freezer door models

1. Unplug the refrigerator or disconnect the power.

2. Keep the freezer door closed until you are ready to lift it free from the cabinet.
   NOTE: Provide additional support for the door while the hinges are being moved. Do not depend on the door gasket magnets to hold the door in place while you are working.

3. Remove the parts for the top hinge as shown below. Lift the refrigerator door free from the cabinet.

4. Remove the center hinge pin and remove the hinge screws as shown below. Lift the freezer door free from the cabinet.

5. Remove the base grille by grasping the grille firmly with both hands and pulling it toward you.

6. Remove the parts for the bottom hinge as shown below.

WARNING

Electrical Shock Hazard

• Disconnect power before removing doors.
• Failure to do so could result in death or electrical shock.

FRENCH DOORS

1. Unplug the refrigerator or disconnect the power.

2. Keep the refrigerator doors closed until you are ready to lift them free from the cabinet.
   NOTE: Provide additional support for the refrigerator door while the hinges are being removed. Do not depend on the door gasket magnets to hold the door in place while you are working

3. Starting with the right-hand side door, remove the parts for the top hinge as shown below. Lift the refrigerator door from the bottom hinge pin.

4. Remove the hinge pin cover from the bottom hinge pin and keep it for later use.

5. Before removing the left-hand side door, disconnect the wiring plug located on top of the top hinge by wedging a flatblade screwdriver or your fingernail between the two sections.

6. Remove the parts for the left-hand side door top hinge as shown in the Top Hinge graphic in Step 3. Lift the door from the bottom hinge pin.
   NOTE: Remove the hinge pin cover from the bottom hinge pin and keep it for later use.

Reverse Doors (optional)

IMPORTANT:
If you want to reverse your door so it opens from the opposite side, follow these steps. If you are not reversing the door, see “Replace Door(s) and Hinges.”

Cabinet

1. Remove hinge screws from handle side and move them to opposite side.

Refrigerator door

1. Remove the refrigerator handle assembly. See “Remove and Replace Door Handles.” Keep all parts together.
2. Remove door handle seal screw front. Move to opposite side of refrigerator door as shown below.
3. Remove the door stop. Move it to the opposite side of the refrigerator door as shown below.
4. Attach the refrigerator handle on the opposite side of the refrigerator door with the two screws. Replace handle trim. See “Remove and Replace Door Handles.”
5. Tighten all screws. Set aside the door until the hinges and freezer compartment drawer are in place.

Freezer door

1. Remove the freezer handle assembly. See “Remove and Replace Door Handles.” Keep all parts together.

2. Remove the door stop. Move to the opposite side of the freezer door as shown below.

3. Attach handle to the opposite side of the freezer door.

4. Tighten all screws. Set the door aside.

5. Remove the base grille by grasping the grille firmly with both hands and pulling it toward you.
   NOTE: Place a shim under the bottom front edge of the refrigerator cabinet to take the weight off the roller brackets.

6. Remove the screws from both roller brackets as shown below.

7. Remove the hinge plate located behind the roller bracket and move it to the opposite side of the refrigerator. Move the hinge pin and shim to the outside hole on the hinge plate as shown below.

Replace Doors and Hinges

NOTE: The graphic may be reversed if the door swing is reversed.

Standard Door – Freezer drawer models

1. Replace the parts for the bottom hinge as shown below. Tighten screws.
   NOTE: Provide additional support for the door while the hinges are being moved. Do not depend on the door gasket magnets to hold the door in place while you are working.

2. Assemble the parts for the top hinge as shown below. Do not tighten the screws completely.

3. Adjust the door so that the bottom of the refrigerator door is aligned with the top of the freezer drawer. Tighten all screws.

Standard Door – Freezer door models

1. Make sure the hinge plate is securely fastened behind the roller bracket and that the hinge pin is inserted into the outside hole. Fully tighten all roller bracket screws.

2. Remove the shim that you placed under the front edge of the refrigerator cabinet. Replace the freezer door
   NOTE: Provide additional support for the door while the hinges are being moved. Do not depend on the door gasket magnets to hold the door in place while you are working.

3. Assemble the parts for the center hinge as shown below, and tighten all the screws. Replace the refrigerator door.

4. Assemble the parts for the top hinge as shown below. Do not tighten the screws completely.

5. Adjust the doors so that the bottom of the refrigerator door is aligned with the top of the freezer door. Tighten all screws.

French Door Models

1. Assemble the parts for the top hinges as shown below. Do not tighten the screws completely.

2. Replace the parts for the bottom hinges as shown below. Tighten screws. Replace the refrigerator doors.
   NOTE: Provide additional support for the refrigerator doors while the hinges are being moved. Do not depend on the door gasket magnets to hold the doors in place while you are working.

3. Align each door so that the bottom of the refrigerator door aligns evenly with the top of the freezer drawer. Tighten all screws.

4. Reconnect the wiring plug on top of the left-hand side refrigerator door. Replace the top hinge covers.

Remove and Replace Freezer Drawer

IMPORTANT:
Two people may be required to remove and replace the freezer drawer.

REMOVE DRAWER FRONT

1. Open the freezer drawer to full extension.

2. Loosen the four screws attaching the drawer glides to the drawer front as shown below.
   NOTE: Loosen screws three to four turns. Keep the screws in the drawer front.

3. Lift the drawer front upward and off the screws.

Replace Drawer Front

1. Slide the drawer glides out of the freezer compartment. Insert the screws in the top of the drawer front into the slots in the drawer brackets as shown below.
2. Pull the drawer brackets toward you to insert the two screws in the bottom of the drawer front into the brackets as shown below..
3. Completely tighten the four screws.

Final Steps

1. Check all holes to make sure that hole plugs and screws are in place. Reinstall top hinge cover.

2. Replace the base grille.
   WARNING
   Electrical Shock Hazard
   

   • Plug into a grounded 3-prong outlet.
   • Do not remove the ground prong.
   • Do not use an adapter.
   • Do not use an extension cord.
   • Failure to follow these instructions can result in death, fire, or electrical shock.

3. Plug into a grounded 3-prong outlet.

4. Return all removable door parts to the door and food to the refrigerator.

Door Closing and Door Alignment
The base grille covers the leveling screws and roller assemblies located at the bottom of the refrigerator cabinet below the freezer door or drawer. Before making adjustments, remove the base grille and move the refrigerator to its final location.

1. Remove the two screws fastening the base grille to the cabinet, and set the screws aside. Grasp the grille and pull it toward you.

2. Move the refrigerator to its final location.
   NOTE: To allow the refrigerator to roll easier, raise the leveling legs off the floor by turning the leveling screws counterclockwise. The front rollers will be touching the floor.

3. So the doors will close easier, use a 1/4″ hex driver to turn both leveling screws clockwise. This will raise the front of the refrigerator tilting it slightly downward to the rear. Turn both leveling screws the same amount.
   NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling screws. This makes it easier to turn the screws .

4. Open and close the doors to make sure they close as easily as you like. If not, increase the tilt by turning both leveling screws clockwise. It may take several turns of the leveling screw to allow the doors to close easier.

5. Check for door alignment. If one door is lower than the other, adjust the leveling screw, on the lower side of the refrigerator. Using a 1/4″ hex driver, turn the screw clockwise to raise that side of the refrigerator until the doors are aligned. It may take several turns of the leveling screw to raise the refrigerator. NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling screws. This makes it easier to turn the screws.

6. Make sure the refrigerator is steady. If the refrigerator seems unsteady or rolls forward when the door or drawer is opened adjust the leveling screws. Using a 1/4″ hex driver, turn the leveling screw on each side clockwise until the rollers are up and the leveling feet are firmly against the floor.
   NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling screws. This makes it easier to turn the screws.

7. Replace the base grille by aligning the ends of the grille with the leveling assemblies on each side and snapping the grille into place.

PERFORMANCE DATA SHEET

Water Filtration System
Model W11569863 (PID), W11569861 (Without PID)

Replacement element model numbers:
EDRARXD1/EDRARXD1B/W11536439/WHRARXD1/ WHRARXD1B/ KADARXD1/ KADARXD1B/ MAYARSD1B/ MAYARXD1B Capacity 200 Gallons (757 Liters) with PID W11569863, 100 Gallons (379 Liters) without PID W11569861.

System tested and certified by UL LLC against NSF/ANSI Standard 42, 53, 401, and CSA B483.1 for the reduction of contaminants specified on the Performance Data Sheet below.

This system has been tested according to NSF/ANSI Standards 42, 53, 401, and CSA B483.1 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42, 53, 401, and CSA B483.1.

Substance Reduction Aesthetic Effects| Influent Challenge Concentration| Maximum Permissible Product Water Concentration| Average % Reduction| Minimum % Reduction
---|---|---|---|---
Chlorine Taste/Odor| 2.0 mg/L ± 10%| ≥50% reduction| 99.39| 99
Particulate Class I*| At least 10,000 particles/ mL| ≥85% reduction| 99.52| 99.33
Contaminant Reduction| Influent Challenge Concentration| Maximum Permissible Product Water Concentration| Average % Reduction| Minimum % Reduction
---|---|---|---|---
Lead: @ pH 6.5 /

@ pH 8.5

| 0.150 mg/L ± 10%| 0.005 mg/L| 99.29/99.84| 99.07/99.46
Mercury: @ pH 6.5 /

@ pH 8.5

| 0.006 mg/L ± 10%| 0.002 mg/L| 97.38/92.78| 92.98/75.86
Asbestos| 107 to 108 fibers/L††| ≥99%| >99| >99
Cysts†| 50,000/L min.| ≥99.95%| ≥99.997| >99.997
Atrazine| 0.009 mg/L ± 10%| 0.003 mg/L| >98.98| >98.95
Benzene| 0.015 mg/L ± 10%| 0.005 mg/L| >99.28| >99.17
Carbofuran| 0.080 mg/L ± 10%| 0.040 mg/L| 83.93| 58.7
Lindane| 0.002 mg/L ± 10%| 0.0002 mg/L| 95.22| 95
P-Dichlorobenzene| 0.225 mg/L ± 10%| 0.075 mg/L| 99.95| 99.95
Tetrachloroethylene| 0.015 mg/L ± 10%| 0.005 mg/L| 99.33| 99.29
Toxaphene| 0.015 mg/L ± 10%| 0.003 mg/L| 99.27| 99.17
O-Dichlorobenzene| 1.8 mg/L± 10%| 0.6 mg/L| >99.995| >99.995
Toluene| 3.0 mg/L ± 10%| 1.0 mg/L| >99.996| >99.996
Styrene| 2.0 mg/L ± 10%| 0.1 mg/L| >99.995| >99.993
1,2,4-Trichlorobenzene| 0.210 mg/L ± 10%| 0.07 mg/L| >99.55| >99.42
Trichloroethylene| 0.3 mg/L ± 30%| 0.005 mg/L| >99.96| >99.95
Endrin| 0.006 mg/L± 10%| 0.002 mg/L| 92.32| 83.93
Contaminant Reduction| Influent Challenge Concentration| Maximum Permissible Product Water Concentration| Average % Reduction| Minimum % Reduction
---|---|---|---|---
Ethylbenzene| 2.1 mg/L ± 10%| 0.7 mg/L| >99.99| >99.99
2,4 – D| 0.210 mg/L ± 10%| 0.07 mg/L| 98.89| 94.76
Turbidity| 11 NTU ± 10%| 0.5 NTU| 98.88| 98.17
Atenolol| 200 ± 20%| 30 ng/L| 95.27| 94.98
Carbamazepine| 1400 ± 20%| 200 ng/L| 96.2| 96.09
Linuron| 140 ± 20%| 20 ng/L| 93.53| 92.31
Meprobamate| 400 ± 20%| 60 ng/L| 94.54| 94.32
Trimethoprim| 140 ± 20%| 20 ng/L| 96.27| 95.94
DEET| 1400 ± 20%| 200 ng/L| 96.32| 96.21
Metolachlor| 1400 ± 20%| 200 ng/L| 96.67| 96.5
Bisphenol A| 2000 ± 20%| 300 ng/L| 95.07| 94.82
Estrone| 140 ± 20%| 20 ng/L| 96.27| 96.15
Nonylphenol| 1400 ± 20%| 200 ng/L| 92.61| 90.48
Naproxen| 140 ± 20%| 20 ng/L| 96.09| 95.83
Ibuprofen| 400 ± 20%| 60 ng/L| 95.44| 95.13
TCPP| 5000 ± 20%| 700 ng/L| 92.78| 92.59
TCEP| 5000 ± 20%| 700 ng/L| 96.62| 96.55
Phenytoin| 200 ± 20%| 30 ng/L| 95.6| 95.12
VOC**| 0.300 mg/L ± 10%| 0.015 mg/L| >99.58| >96.21

Test Parameters:
pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.70 gpm (2.65 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 200 gallons (757 liters) with PID, 100 gallons (379 liters) without PID.

The compounds certified under NSF 401 have been deemed as “emerging compounds/incidental contaminants.” Emerging compounds/incidental contaminants compounds that have been detected in drinking water supplies at trace levels. While occurring at only trace levels, these compounds can affect the public acceptance/ perception of drinking water quality.

• It is essential that operational, maintenance, and filter replacement requirements be carried out for the product to perform as advertised. Property damage can occur if all instructions are not followed.

• The disposable cartridge must be changed at least every 6 months. Spent adsorption media will not be regenerated and used.

• Use replacement EDRARXD1/B, WHRARXD1/B, KADARXD1/B, MAYARXD1/. 2022 suggested retail price of $49.99 U.S.A./$49.95 Canada. Prices are subject to change without notice. Available at www.everydropwater.com.

• The filter monitor system measures the amount of water that passes through the filter and alerts you when it is time to replace the filter. To learn how to check the water filter status, see “Using the Controls” or “Water Filtration System” in the User Instructions or User Guide.

• After changing the water filter, flush the water system. See “Flush the Water Systems” or “Water Dispenser” in the User Instructions or User Guide.

• These contaminants are not necessarily in your water supply. While testing was performed under standard laboratory conditions, actual performance may vary.

• The product is for cold water use only.

• The water system must be installed in compliance with state and local laws and regulations.

• Actual performance may vary as the testing was performed under standard laboratory conditions.

• Do not use water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts. EPA Est. No. 85075-SG-001

• Refer to the “Warranty” section (in the User Instructions or User Guide) for the Manufacturer’s limited warranty, name and telephone number.
  Application Guidelines/Water Supply Parameters

  • Water Supply Potable City or Well
  • Water Pressure 30 psi – 120 psi (207 kPa – 827 kPa)
  • Water Temperature 33°F – 100°F (0.6°C – 37.8°C)
  • Service Flow Rate 0.52 gpm (1.97 Lpm) @ 60 psi (413.7 kPa)

• Your water filtration system will withstand up to 120 pounds per square inch (psi) of water pressure. If your water supply is higher than 80 psi, install a pressure-reducing valve before installing the water filtration system.

• Conforms to NSF/ANSI 53 for VOC reduction. See the Table below for individual contaminants and reduction performance.

• Class I particle size: >0.5 to >1 um

• This VOC performance accounts for 39 contaminant removals based on VOC surrogate testing †Based on the use of polystyrene microsphere

  • Fibers greater than 10 um in length

Performance data sheet reduction claims for organic chemicals included by surrogate testing

Substance| Influent challenge concentration (mg/L)| Maximum permissible product water concentration (mg/L)
---|---|---
alachlor| 0.050| 0.001
altrazine| 0.100| 0.003
benzene| 0.081| 0.001
carbofuran| 0.190| 0.001
carbon tetrachloride| 0.078| 0.0018
chlorobenzene| 0.077| 0.001
chloropicrin| 0.015| 0.0002
2,4–d| 0.110| 0.0017
dibromochloropropane (DBCP)| 0.052| 0.00002
o-dichlorobenzene| 0.080| 0.001
p-dichlorobenzene| 0.040| 0.001
1,2-dichloroethane| 0.088| 0.0048
1,1-dichloroethylene| 0.083| 0.001
cis-1,2-dichloroethylene| 0.170| 0.0005
trans-1,2-dichloroethylene| 0.086| 0.001
1,2-dichloro propane| 0.080| 0.001
cis- 1,3-dichloro propylene| 0.079| 0.001
dinoseb| 0.170| 0.002
endrin| 0.053| 0.00059
ethylbenzene| 0.088| 0.001
ethylene dibromide (EDB)| 0.044| 0.00002
haloacetonitriles (HAN)|  |
bromochloroacetonitrile| 0.022| 0.0005
dibromo acetonitrile| 0.024| 0.0006
dichloroacetonitrile| 0.0096| 0.0002
trichloraacetonitrile| 0.015| 0.0003
halo ketones (HK)|  |
1,1–dichloro-2–propanone| 0.0072| 0.0001
1,1,1–trichloro-2–propanone| 0.0082| 0.0003
heptachlor| 0.025| 0.00001
heptachlor epoxide| 0.0107| 0.0002
hexachlorobutadience| 0.044| 0.001
hexachlorocyclopentadiene| 0.060| 0.000002
lindane| 0.055| 0.00001
methoxychlor| 0.050| 0.0001
pentachlorophenol| 0.096| 0.001
simazine| 0.120| 0.004
Substance| Influent challenge concentration (mg/L)| Maximum permissible product water concentration (mg/L)
---|---|---
styrene| 0.150| 0.0005
1,1,2,2–tetrachloroethane| 0.081| 0.001
tetrachloroethylene| 0.081| 0.001
toluene| 0.078| 0.001
2,4,5–TP (Silvex)| 0.270| 0.0016
tribromoacetic acid| 0.042| 0.001
1,2,4–trichlorobenzene| 0.160| 0.0005
1,1,1–trichloroethane| 0.084| 0.0046
1,1,2–trichloroethane| 0.150| 0.0005
trichloroethylene| 0.180| 0.0010
trihalomethanes (includes) chloroform (surrogate chemical)

bromoform bromodichloromethane

chlorodibromomethane

| ****

0.300

| ****

0.015

xylenes (total)| 0.070| 0.001

Consumer Support 1.800.442.9991 By Whirlpool Corporation 2000 North M63 Benton Harbor, MI 49022.

©2022 All rights reserved. Used under license in Canada.

References

• Home | Everydrop Water

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>