8BitDo SN30 Pro Bluetooth Gamped Instruction Manual

8BitDo SN30 Pro Bluetooth Gamped

SN30 Pro Bluetooth gamepad

• Power off: press and hold start for 3 seconds
• Power on: press start. Controller stays on its previous mode

Switch

• Motion controls, NFC scanning, IR camera, HD rumble, noti1ication LED are not supported, nor can the system be waken up wirelessly

Bluetooth connection

1. – Press V + start to turn on the controller. LED starts to rotate from left to right
2. – Press pair button for 3 seconds to enter its pairing mode. LED stops blinking for a short moment then starts to rotate again (this is required for the very first time only)
3. – Go to your Switch Home Page to click on Controllers, then click on Change Grip/Order
4. – LED becomes solid when connection is successful

• Controller will auto reconnect to your Switch with the press of start once it has been paired

Wired connection

1. – Press V + start to turn on the controller. LED starts to rotate from left to right
2. – Connect the controller to your Switch dock via its use cable
3. -Wait till the controller is successfully recognized by your Switch to play

• Switch system needs to be 3.0.0 or above for 2.4g connection. Go to System Setting> Controller and Sensors> turn on Pro Controller Wired Communication
• LED lights indicate the player number, 1 LED indicates player 1, 2 LEDs indicate player 2, 4 is the maximum number of players the controller supports

Windows CX – input)

Bluetooth connection

• Required system: Windows 10 (1703) or above. Bluetooth 4.0 is supported

1. – Press X + start to turn on the controller. LEDs1 & 2 start to blink
2. – Press pair button for 3 seconds to enter its pairing mode. LED starts to rotate from left to right (this is required for the very first time only)
3. – Go to your Windows device’s Bluetooth setting > Bluetooth & other devices > turn it on
4. – Choose Bluetooth & other devices – Bluetooth
5. – Pair with [8BitDo SN30 Pro] 6 – LED becomes solid when connection is successful

• Controller will auto reconnect to your Windows device with the press of start once it has been paired

Wired connection

1. – Press X + start to turn on the controller. LEDs1 & 2 start to blink
2. – Connect the controller to your Windows device via its USB cable
3. – Wait till the controller is successfully recognized by your Windows device to play

• LED lights indicate the player number, 1 LED indicates player 1, 2 LEDs indicate player 2, 4 is the maximum number of players the controller supports

Android (D – input)

• Required system: Android 4.0 or above

Bluetooth connection

1. – Press B + start to turn on the controller. LED 1 starts to blink
2. – Press pair button for 3 seconds to enter its pairing mode. LED starts to rotate from left to right (this is required for the very first time only)
3. – Go to your Android device’s Bluetooth setting, pair with [Beit Do SN30 Pro]
4. – LED becomes solid when connection is successful

• Controller will auto reconnect to your Android device with the press of start once it has been paired

Wired connection

1. – Press B + start to turn on the controller. LED 1 starts to blink
2. – Connect the controller to your Android device via its use cable
3. – Wait till the controller is successfully recognized by your Android device to play

• OTG support is required on your Android device

macOS

• Required system: OS X Lion (10.7) or above

Bluetooth connection

1. – Press A+ start to turn on the controller, LEDs 1, 2 & 3 start to blink
2. – Press pair button for 3 seconds to enter its pairing mode. LED starts to rotate from left to right (this is required for the very first time only)
3. – Go to your macOS device’s Bluetooth setting and turn it on
4. – Pair with [Wireless Controller]
5. – LED becomes solid when connection is successful

• Controller will auto reconnect to your macOS device with the press of start once it has been paired

Wired Connection

1. – Press A+ start to turn on the controller, LEDs 1, 2 & 3 start to blink
2. – Connect the controller to your macOS device via its use cable
3. – Wait till the controller is successfully recognized by your macOS device to play

Turbo function

1. – Hold the button you would like to set turbo functionality to and then press the star button to activate its turbo functionality
2. – Home LED blinks continuously when the button with turbo functionality is pressed
3. – Hold the button with turbo functionality then press star to deactivate its turbo functionality

• D- pad joysticks, home, select and start buttons are not included
• This does not apply to Switch mode

Battery

• 480 mAh built-in Li-poly battery with 16 hours of playtime
• Rechargeable with1-2 hour charging time
• Controller will turn off in 1 minute with no connection and 15 minutes with Bluetooth connection but no use
• Controller stays on with wired connection

Support

• Please visit support.8bitdo.com for further information & additional support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>