FENIX E05R Flashlight Instruction Manual
- June 6, 2024
- FENIX
Table of Contents
FENIX E05R Flashlight Instruction Manual
Technical Parameters
| ANSI/ PLATO FL1 | Burst | High | Med | Low |
|---|
Output
| 400 lumens| 150 lumens| 25 lumens| 3 lumens
Runtime
| /| 55 minutes*| 5 hours| 30 hours
Distance
| 64 meters| 40 meters| 17 meters| 8 meters
Intensity
| 1046 candela| 412 candela| 72 candela| 15 candela
Impact Resistance
| 1 meter
Submersible
| IP68
Note: According to the ANSI/PLATO FL1 standard, the above specifications are from the results produced by Fenix through its laboratory testing using the built‐in 320mAh Li‐polymer battery under the temperature of 21±3°C and humidity of 50% ‐ 80%. The true performance of this product may vary according to different working environments.
The High output is measured in a total of runtime including output at reduced levels due to temperature or protection mechanism in the design.
Product Features
- 400 lumens maximum output, 64 meters maximum beam distance.
- Cree XP‐G2 S3 white light LED with a lifespan of 50,000 hours.
- Built‐in 320mAh Li‐polymer battery.
- Hidden micro USB charging port.
- Metal switch for on/off and output selection.
- Instant Burst.
- High‐efficiency lens with a total reflective coating.
- Made of durable A6061‐T6 aluminum.
- Premium type HAIII hard‐anodized anti‐abrasive finish.
- Size: 2.68” x 0.60” x 0.59” / 68 x 15.3 x 15 mm.
- Weight: 0.85 oz / 24 g.
Operating Instruction
On/off
Press and hold the side switch for 0.5 seconds to turn on/off the light.
Output Selection
With the light switched on, single click the side switch to cycle through
Low→Med→High.
Instant Burst
Press and hold the side switch for 1.2 seconds to enter instant Burst, release
it the light will turn back to Low mode.
Lock/Unlock
Lock: with the light switched off, double click the switch within 0.5 seconds
to lock the light, the light will blink twice on Low to indicate locked
status.
Unlock: with the light locked, double click the switch within 0.5 seconds, the
light will be unlocked and activated on Low.
In locked status, clicking or pressing the switch will activate 2 one‐second blinks on Low to indicate locked status.
Charging
- First loosen the light body to reveal the Micro USB charging port and plug the USB A socket of the charging cable into an electrical outlet, then connect the micro USB socket of the charging cable to the light.
- The indicator will display red while charging and will turn green when fully charged.
- Once charging is completed, be sure to tighten the light head to maintain the dustproof and waterproof ability.
Note
- Charge the light timely when the battery power gets too low to ensure the normal life of the battery.
- The normal charging time is approximately 1 hour from depletion to full charging.
- Recharge a stored light every four months to maintain the optimum performance of the battery.
Intelligent Overheat Protection
The light will accumulate a lot of heat when used at High mode for extended periods. When the light reaches a temperature of 60°C or above, the light will automatically step down a few lumens to reduce the temperature. When the temperature drops below 60°C, it will then allow the user for the reselection of the mode.
Usage and Maintenance
- Disassembling the sealed head can cause damage to the light and will void the warranty.
- Lock the light to prevent accidental activation during storage or transportation.
- Long‐term use can result in O‐ring wear. To maintain a proper water seal, replace the ring with an approved spare.
Included
Fenix E05R flashlight, Micro USB charging cable, Key chain, Spare O‐ring, User manual, Warranty card
Warning
- The flashlight is a high‐intensity lighting device capable of causing eye damage to the user or others. Avoid shining the light directly into anyone’s eyes.
- This flashlight will accumulate a lot of heat when used for extended periods, resulting in a high temperature of the flashlights hell. Pay attention to safe use to avoid scalding.
- Do not shine an object at close range, to avoid burning the object or causing danger due to high temperature.
- The LED of this flashlight is not replaceable; so the entire light should be replaced when the LED reaches the end of its life.
- If any of the information provided in this manual is changed, the new version of the manual shall prevail; if your included user manual is an old one, it acquiesces that we won’t send a new manual.