HORNBACH ATO-FH-03 3000 Watt Portable Industrial Electric Fan Heater User Manual

: June 9, 2024
: HORNBACH

Table of Contents

HORNBACH ATO-FH-03 3000 Watt Portable Industrial Electric Fan Heater
INFORMATION REQUIRMENT
Introduction
Specifications
Warnings
Control panel
Set-up and Operation
Safety features
Cleaning and Maintenance
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

HORNBACH ATO-FH-03 3000 Watt Portable Industrial Electric Fan Heater

INFORMATION REQUIRMENT

Information required for the electric local space heaters

Introduction

This manual describes the correct and safe use of this device. Keep this manual for future reference. The manual is an essential part of the device and must be given to the new owner upon resale or exchange. This manual has been compiled with the utmost care. Nevertheless, we reserve the right to improve and adjust this manual at any time. The images used may differ. The following symbols and terms are used in this manual to alert the reader on safety issues and important information:

WARNING Indicates a hazardous situation which, if the safety instructions are not followed, can lead to injuries to the operator or bystanders, light and/or moderate damage to the product or to the environment.
CAUTION Indicates a hazardous situation which, if the safety instructions are not followed, can lead to light and/or moderate damage to the product or to the environment.
CAUTION In order to avoid overheating, do not cover the heater.

Identification

HORNBACH-ATO-FH-03-3000-Watt-Portable-Industrial-Electric-Fan-
Heater-1

Specifications

Product size: 200 x 230 x 320 mm
Weight: 3.5 kg
Voltage: 220-240 V~ 50Hz
Power (L/M/H): 1000/2000/3000 W
Protection rating: IP24
Protective class: Class I

Description
The Elektro-Heizlüfter 3000 Watt is an easy-to-use electric heater for indoor domestic and light commercial use.

Warnings

Safety warning – general

Read the user instructions carefully and completely before using (and installing) this device. Keep the instruction leaflet somewhere safe so that you can consult it and pass it on in future.
Before use, check your new device (including cable and plug) for any visible damage. Never use a damaged device but take it back to the supplier for a replacement.
In the event of incorrect usage or installation, there is a risk of electric shocks and/or a fire hazard.

Warnings – device position

Do not place the device near, under or facing an electrical socket and not in the vicinity of an open fire or heat source.
To reduce the risk of fire keep textiles, curtains, or any other flammable material a minimum distance of 1 meter from the air outlet.
Do not use the heater outdoors or in areas that are smaller than 20m³.
The device contains hot and/or glowing and sparking components. Do not, therefore, use where fuels, paint, flammable fluids and/or gases are stored. Do not use the device in an environment that poses a fire risk, e.g. near gas tanks, gas pipes or aerosols. This is an explosion and fire risk!
This device is not suitable for wall or ceiling installation.
Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool.
This device is splash-proof but even though it is a mobile device, it is not suitable for use in bathrooms or near a swimming pool. Do not place the device near water-points and/or water reservoirs. Make sure that the device cannot fall into water and that it cannot be penetrated by water. If the device does get wet make sure you remove the plug from the socket! Do not use a device that is wet inside but take it to be repaired. Never immerse the device, cable or plug in water or any other fluid and never touch device with wet hands.
The air around the device must be able to circulate freely. Never install it too close to walls or large objects and never under a shelf, cupboard, curtains or similar. When locating the device, make sure you have the following minimum free space:
- Front, minimum free space 100 cm
- Back, minimum free space 100 cm
- Sides, minimum free space 100 cm
- Top, minimum free space 100 cm
Use this heater on a horizontal and stable surface.
The base on which the device is placed must not be made of flammable materials. It must be resistant to temperatures of at least 125°C without burning, melting,
deforming or bursting into flames. Check regularly to ensure that the surface is not overheating; this could be dangerous!
Never place the device on surfaces such as beds or deep-pile carpet as openings could be blocked.
Do not place the device near an open window as rain could blow in; do not place on wet surfaces and avoid any liquids being spilt nearby. Do not place the device behind a door or along a walking route to avoid accidental trips.
The heater must not be located immediately below a socket outlet.
Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.

Warnings – use

Do not use additions/accessories on the device that have not been supplied or approved by the manufacturer.
Only use the device for its intended purpose and in the manner set out in this instruction leaflet.
Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.
Never cover or block the device; it will overheat and this could lead to a fire risk. Never hang or place objects such as clothing, blankets, cushions, paper, etc. on the device. The minimum distance of 1 meter between the device and flammable materials must always be applied. Ventilation openings should never be blocked as this may pose a fire risk. Never use the device to dry clothing or place anything on it. Do not let anything lean against the device!
Do not use this heater with a programmer, timer, separate remote-control system or any other device that switches the heater on automatically, since a fire rest exists if the heater is covered or positioned incorrectly. Never use the device with an external voltage regulator such as a dimmer or similar, as this could be dangerous!
This device is exclusively intended to be used for heating workplaces such as workshops, garages, storage spaces, etc. You must only use the device for this purpose.
The connection voltage and frequency, as given on the device, must correspond to that of the socket to be used. The electrical socket to be used must be an earthed connection. The electrical installation must be protected via a 30 mA earth leakage circuit breaker. The electrical socket that you are using must be to hand at all times in order to be able to remove the plug from the socket in the event of an emergency.
To avoid overloading and/or fuses being blown, do not use any other equipment on the same socket or electrical group as the one used for the device.
Unroll the electric cable for the device fully before inserting the plug into the socket and ensure that the electrical cable does not come into contact with the fireplace or get hot. Do not run the electrical cable under carpet, cover with mats, runners or similar and do not place in areas that are walked on frequently. Ensure that it cannot be stepped on and that no furniture is placed on top of it. Do not bend the electrical cable around sharp corners and do not roll up too tightly after use! Prevent the electrical cable coming into contact with oil, solvents and sharp objects. Check the cable and plug regularly for damage. Do not bend or pinch the electrical cable and do not wind it around the device; this could damage the insulation!
The use of an extension cable is not advised as this can lead to overheating and fire. If the use of an extension cable is unavoidable, make sure that it is not damaged and that it is an approved extension cable with a minimum diameter of 3×2,5 mm² and a minimum permitted capacity of 3500 Watt. Always fully extend the cable in order to prevent overheating.
Only connect the device to a fixed socket. Do not use multi-plug adapters or similar.
During use, the plug may begin to feel warm; this is normal. If it’s really warm, there may be something wrong with the socket. Please contact your electrician.
Always turn off the device and remove the plug from the power socket: Never turn the device off using the plug!
Prevent foreign objects entering the radiation/ventilation or outlet openings on the device. This may cause electric shock, fire or damage.
Never leave a working device unattended but switch off and then remove the plug from the socket.
Always remove the plug from the socket when the unit is not in use! Always remove plug by pulling on the plug itself; never pull on the electrical cable!
This device gets hot during use. Never touch the device when it is on or shortly thereafter; it could burn you.
Never operate the device with wet hands.
Do not use this heater if it has been dropped.
Do not use this heater if there are visible signs of damage to the heater.

Who can use the device

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or a lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
Children of less than 3 years should be kept away unless continuously supervised.
Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.

Warnings for maintenance

Keep the device clean. Dust, dirt and/or deposits in the device often lead to overheating. Ensure that this type of build-up is regularly removed.
Always switch the device off, remove plug from socket and let the device cool down before you:
- clean the device
- users – maintain the device.
- touch or move the device.
Never switch the device on if you have noticed damage to the device itself, the cable or plug or if it does not work properly, makes strange noises, smells odd or you can see smoke, or if it has fallen or shows any other signs of damage. Remove the plug from the socket immediately. Take the entire device back to your supplier or a recognized electrician to be checked and/or repaired. Always ask for original parts to be used.
The device may only be opened and/or repaired by a competent and qualified person. Do not carry our your own repairs as this could be dangerous! Repairs carried out by unauthorized persons or changes made to the device could damage the dust/waterproof capacity of the device and will nullify the guarantee and the manufacturer’s liability.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
Failing to adhere to points 3, 4, 5, could lead to damage, fire and/or personal injury. They will invalidate the guarantee and the supplier, importer and/or manufacturer shall not be liable for the consequences.

Description
Elektro-Heizlüfter 3000 Watt are ‘real space’ heaters, with a powerful fan which disseminates a great deal of air. Cold air is sucked in at the back, heated, and then blown out as hot air. Because a relatively large quantity of air is sucked in and blown out, the air expelled by the heater does not feel particularly hot. As a great deal of air is heated and blown out, however, the entire space (not just the air around the heater!) is gradually warmed up.

Control panel

The control panel consists of two dials: HORNBACH-ATO-FH-03-3000-Watt-
Portable-Industrial-Electric-Fan-Heater-2

The mode selector dial with 4 positions is located on the left.
From top to bottom:
- O or off
- 1000W power
- 2000W power
- 3000W power
The continuously adjustable thermostat dial is located on the right.

Location and Connection

Remove all packaging material and keep out of reach of children. After removing packaging, check the appliance for damage or other signs that could indicate a fault/defect/malfunction. In case of doubt, do not use the appliance, but contact your vendor for inspection or replacement.
Select a suitable location for the device taking into account all the aforementioned warnings in this manual.
Make sure the heater is switched off (switch to O position), then plug into a correctly functioning 220-240V~ 50Hz socket. Only connect the heater to an earthed socket!

Set-up and Operation

If the heater is being used for the first time (or if you want to reset the desired temperature), turn the thermostat dial to the maximum position (clockwise as far as it goes). With the mode selector dial, adjust the heater to suit your preferences. Once the temperature in the area being heated has reached the right level, slowly turn the thermostat dial anticlockwise until you hear a soft click; leave the dial in that position. The heater will automatically maintain the temperature at this level. It does this by switching the heating elements off and on when the temperature rises or falls too much.

Note! After the thermostat has switched the heating elements off, the fan will keep turning. This means that the air is constantly moved, allowing the heater to accurately detect if the area is cooling down. The thermostat dial is continuously adjustable. A higher temperature is set by turning it clockwise; a lower temperature by turning it anticlockwise.

Safety features

Tipping safeguard
The heater is fitted with a tipping safeguard which switches the heater off if it accidentally falls over. Once it is placed upright, it will begin to work again but you must unplug and check the heater for damage before reusing. If you find damage or the heater does not work correctly, do not use and have it checked or repaired!

Overheating safeguard
In case of internal overheating, the overheating safeguard will switch the heater off. If this occurs, immediately turn the mode selector dial to O, unplug and allow heater to cool down for at least 10 minutes. In theory, the heater can now be used as normal. There is, however, generally a reason for an appliance overheating. This may be because the heater cannot adequately release its heat or take in fresh air (because the heater is covered, the grills are blocked, the heater is placed too near a wall etcetera). Before using the heater again, therefore, remove or adjust whatever caused the appliance to overheat. If you cannot find the cause and overheating recurs, stop using the heater and contact your vendor or a certified electrician for inspection/repair. Overheating poses a serious fire risk!

Cleaning and Maintenance

Keep the heater clean. Deposits of dust and dirt in the appliance are a common cause of overheating so these should be removed regularly. Switch off the heater, remove the plug from the socket and allow the heater to cool down before cleaning or carrying out maintenance work.

Wipe the outside of the heater regularly with a dry or slightly damp cloth. Do not use aggressive soaps, sprays, cleaners or abrasives, waxes, polishes or chemical solutions!
Use a vacuum cleaner or compressor to carefully remove any dust and dirt from the grills and ensure that the air intake and outlet openings are clean. Be careful not to touch or damage any internal parts during cleaning!
The heater contains no other parts which need maintenance.
At the end of the season, store the cleaned heater in the original packaging if possible. Store upright in a cool, dry and dust-free place.

Disposal
At its end of life, discard the device according to the local laws and regulations, or deliver the device to your supplier.

HORNBACH Baumarkt AG – Hornbachstraße 11 – 76879 Bornheim – Germany
Model: Elektro-Heizlüfter 3000 Watt
Date: 29/06/2022
Product code: 10534731
Version: v2.0
Declaration of Conformity or User manual can be found at https://www.hornbach.com/productcompliance