HORNBACH 11768 2 In 1 Heavy Duty Shelf and Workbench Instruction Manual

HORNBACH 11768 2 In 1 Heavy Duty Shelf and Workbench

Product Information

The product is a 2-in-1 heavy-duty shelving and workbench with a maximum load capacity of 175 kg per level. It can be set up either as high storage shelving or as two half-height shelves alongside one another, which can be transformed into a workbench. The product comes with a plugin system that makes assembly very easy. It is ideal for use in basements, garages, or workshops.

Product Usage Instructions

Before using the product for the first time, please read through the assembly instructions carefully.

1. Ensure that the packaging materials are kept away from young children and pets as they pose a choking hazard.
2. Take caution when handling the individual parts of the product as they have sharp edges that could cause injury.
3. Assemble the first shelf by attaching the vertical frames to the horizontal beams and securing them in place with screws and bolts.
4. Repeat step three to assemble the second shelf.
5. Attach a connector and an additional vertical frame to each of the already assembled frames to create the workbench.
6. Attach plastic caps to the ends of the vertical frames for safety purposes.
7. Ensure that no excessive force is applied during assembly.
8. Place the product on a stable, even surface after assembly.
9. Remove any stickers, protective films or transportation covers from the product before use.

If you have any questions about the product or need spare parts/accessories, contact the customer service department via their website: www.ds- group.de/kundenservice.

Dear Customer, We are delighted that you have chosen this EASYmaxx 2-in-1 heavy-duty shelving & workbench. You can set it up either as high storage shelving or as two half-height shelves alongside one another which you can then transform into a workbench. Assembly is very easy thanks to the plug-in system. The ideal solution for a basement, garage or workshop! If you have any questions about the product or spare parts/accessories, contact the customer service department via our website: www.ds-group.de/kundenservice Information About the

Assembly Instructions

Before using the product for the first time, please read through these assembly instructions carefully and keep them for future reference and other users. They form an integral part of the product. The manufacturer and importer do not accept any liability if the information in these assembly instructions is not complied with.

ITEMS SUPPLIED

1. Angled profile 900 mm (8 x)
2. Cross beam 900 mm (10 x)
3. Cross beam 400 mm (10 x)
4. Cross strut for shelf (5 x)
5. MDF 3.2 mm shelf (5 x)
6. Plastic protective cap (16 x)
7. Connector for angled profiles (4 x)
8. Assembly instructions (1 x)

Check the items supplied for completeness and the components for transport damage. If you find any damage, do not use the product but contact our customer service department. Remove any possible films, stickers or transport protection from the product

INTENDED USE

• This product is intended to be used as storage shelving or a workbench with a max. load-bearing capacity of 175 kg on each level.
• The product is for personal use only and is not intended for commercial applications.
• Use the product only for the specified purpose and as described in the assembly instructions. Any other use is deemed to be improper. Incorrect use may lead to serious injuries.
• The warranty does not cover faults caused by incorrect assembly, handling, damage or attempted repairs. The same applies to normal wear and tear

SAFETY NOTICES

• Keep the packaging material away from young children and animals. There is a danger of suffocation!
• Supervise young children to ensure that they do not climb up on the product or hang on the product. There is a danger of injury!
• Be careful when handling the individual parts of the product. There is a danger of injury due to sharp edges.
• Do not make any modifications to the product. Use only original accessories from the manufacturer.
• Before you load the product, ensure that it has been assembled correctly and set up safely.
• Load the product as evenly as possible. Place heavy objects nearer the bottom.
• Do not use any corrosive or abrasive cleaning agents! These may damage the surfaces. Dust or clean with a damp cloth if necessary.
• Protect the product from flames, persistent moisture and impacts.

ASSEMBLY

• We recommend that you assemble the product with another person.
• Make sure there is sufficient space for assembly and if necessary use a mat to protect the product or delicate floors from being scratched.
• When you assemble the product, always make sure that all tabs are pushed correctly and fully through the relevant slots. If necessary, use a rubber hammer (not supplied with the product).
• Do not use any force during assembly.
•  Once you have assembled the product, set it up on a horizontal, stable and flat surface

1. Connect two angled profiles (1) to two or three of the 400 mm cross beams (3) (Picture B). Repeat this with two more angled profiles. Place the cross beams at the same height.

2. Connect the assembled side parts to the 900 mm cross beams (2). Place the cross beams at the same height (Picture C, D). The product can then be completed in two different versions:

3. One shelf (height : approx. 180 cm)

4. Two shelves / one workbench (height : approx. 90 cm)
   One Shelf (Height: approx. 180 cm)

5. Place one connector (7) and another angled profile on each of the angled profiles that have already been assembled (Picture E).

6. Fix the rest of the cross beams (2, 3) between the angled profiles that have been placed on (see steps 1 and 2).

7. Place plastic protective caps (6) on the ends of the angled profiles (Picture F).

8. Connect opposite 900 mm cross beams to a cross strut (4) (Picture G). Perform this step on all levels.

9. Place in the shelves (5) (Picture H).

Two Shelves / One Workbench (Height: approx. 90 cm)

1. Repeat steps 1 and 2 with the rest of the angled profiles and cross beams to assemble the second shelf.
2.  Place the plastic protective caps (6) on the ends of all angled profiles (Picture F).
3. Connect opposite 900 mm cross beams to a cross strut (4) (see Picture G). Perform this step on all levels.
4. Place in the shelves (5) (Picture I).

With this particular set-up, the connectors (7) are not required

PRODUCT DATA

• Article number : 11768
• Model number : JHK-15822
• Dimensions (H/W/D) : approx. 180 x 90 x 40 cm or two lots of 90 x 90 x 40 cm
• Weight: approx. 10.2 kg
• Load : max. 175 kg per level
• Material : MDF (shelves); steel, galvanised (angle profiles, cross beams, cross struts, connectors); plastic (protective caps)
• ID of assembly instructions : Z 11768 M DS V1 0123 as

DISPOSAL
Dispose of the packaging material in an environmentally friendly manner so that it can be recycled. Dispose of the product in an environmentally friendly manner as well. All rights reserved

IMPORTER
DS Produkte GmbH Stormarnring 14 22145 Stapelfeld · Germany

CUSTOMER SERVICE
Am Heisterbusch 1 19258 Gallin · Germany
✆ +49 38851 314650 *
Calls to German landlines are subject to your provider’s charges

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>