HORNBACH 10457786 E-Corner 90 Table Frame Instruction Manual

10457786 E-Corner 90 Table Frame
Instruction Manual

E-CORNER 90

Assembly Instructions: Electrical Height Adjustable Desk Frame

E-CORNER 90

TECHNICAL SPECIFICATIONS

1. Electric Components:

consumption

2. Desk Frame
Anti-Collision
Built-in load limit switch

SAFETY AND WARNING!

This product can be used by children aged 8 years and older, persons with reduced physical, sensory or mental capacity as long as they have been given proper instructions and training on how to use the product in a safe way and understand the hazards involved. Children shall not play with the product.

CORRECT DISPOSAL

This sign indicates that this product must not be disposed of through regular household waste within the European Union. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. There you can obtain all information necessary to dispose of this product properly. (WEEE-Reg.-Nr. DE: 52242201)

HANDSET

1. Up / Down Keys
   To adjust the height of the desk, keep pressing the “up” or “down” key until the tabletop reaches the desired position.

2. Display Screen
   Display the height value of the desk.
   

3. Memory Key (1 / 2 / 3 / 4)
   After setting memory keys, the desk will move automatically to the saved position.
   How to set a memory key: Please select the desired position. Then press the S-key. Then press the S-Key, the display will show an “S” and flashes. Whenever a programmed memory key is pressed, the tabletop will automatically adjust to the entered/saved height.

4. Set Key
   The set key saves all changed settings.

5. Anti-collision function
   When the desktop encounters reverse resistance while moving, the desk will stop and move slightly in the opposite direction.

6. Reset Procedure
   1. When the display shows RSE press the DOWN key until the frame reaches its lowest position, you hear a “beep” and the frame rebounds slightly. Now the reset is complete.
   2. To force a re-set you have to move the frame to its lowest position by pushing the DOWN key release the DOWN key briefly and push it again for about 5 seconds until you hear a “beep” and the frame rebounds slightly. The re-set is done. To restore the factory settings (e.g., when a controller is replaced) press the UP and DOWN button simultaneously until you hear a first “beep” after 5 seconds and a second “beep” after 10 seconds. Once the display shows “RST” proceed as described under 1. Above.
   USB-Slot
   With charging function on the back
   

7. Lock / Unlock
   Press the “up” and “S” keys for 5 seconds, Screen displays “LOC”, the system is locked up. Press the “down” and “S” key for 5 seconds, the screen display ”LOC” turn to height, the system is unlocked.

HOW TO ADJUST SETTINGS BY USING THE HAND CONTROL SETS

Press the “S” key for 5 seconds to select between the different settings by using the UP or DOWN key. After you changed a the setting, you have to save the new setting by pressing the “S” key again.

to 8 = most sensitive
S-3 Anti-collision sensitivity moving up| Press “S” and then select: 0 = off (not recommended), 1 = least sensitive to 8 = most sensitive
S-4 Anti-collision sensitivity moving down| Press “S” and then select: 0 = off (not recommended), 1 = least sensitive to 8 = most sensitive
S-5 Display height| Press “S” and then using the up / down keys you can change the display height if necessary
S-6 frame operating mode| Press “S” and then select: 0 = constant touch or 1 = one-touch
S-7 Duty cycle| To deactivate the overheating protection – please do not change it!
S-8 frame tilt sensitivity| Press “S” and then select 0 = off, 1 = 0.5°, 2 = 1.0°, 3 = 1.5°, 4 = 2.0°, 5 = 2.5°, 6 = 3.0°, 7 = 3.5°, 8 = 4.0°

After adjusting all settings you have to press the “S” key again to return to the main menu.
Minimum /Maximum height
To select a minimum height do the following: Move the frame to the desired minimum height. Press the UP & Down key simultaneously for about 5 seconds. A beep indicates
that the minimum height has been set. (IMPORTANT: You can only select a minimum height that is below 96 cm)
To remove the minimum height please move the frame to the programmed minimum height, then press the Up & Down key simultaneously until you hear a beep indicating that the minimum height was deleted. To set/delete the maximum height please proceed the same way. The maximum height must be more than 97 cm.

TROUBLESHOOTING

replaced
E18, E28| Overload protection| Reduce the weight
HOT| Excessive use| Do not use it for 20 minutes. The system will recover automatically.

E-CORNER 90

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>