LOREX W452AS Series Wired Floodlight Security Camera User Manual

: June 9, 2024
: Lorex

Table of Contents

Package Contents
Overview
Mounting Setup
Device App Setup
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

W452AS Series Wired Floodlight Security Camera
User Manual

Package Contents

Tools Needed

Drill
Screwdriver

Overview

LED Panel
IR Light
Camera
Microphone
Speaker
Status Indicator
MicroSD Card Slot
Reset Button*
Mounting Bracket
Floodlight Housing
Security Screw
Rubber Plug
QR Code
PIR Sensor

Status Indicator

| Device Ready
---|---
| Ready for network connection
| Pairing to the Lurex Home app
| Network connection failed / Factory reset
| Firmware updating

Press and hold the reset button until you hear the audio prompts.

WARNING
**** TURN OFF THE POWER RUNNING TO YOUR EXISTING CIRCUIT AT THE BREAKER If you are unsure of which breaker controls the circuit, then turn off the main power switch.
If you do not know where your breaker is or how to turn off power, consult a licensed electrician.
Make sure the supply voltage is correct. 100-240 VAC 50/60Hz is required.
DO NOT connect the floodlight to a dimmer or timer.

Mounting Setup

**** If you are not replacing a light fixture, you will need to run power cabling to the install location, and purchase a UL listed junction box for a licensed electrician to install.

Remove the existing light fixture and bracket from the wall, and then disconnect the wires.
Tip! Bend the power cables so they do not fall through the wall.
Run the existing wires through the middle of the Mounting Plate.
Place and align the Mounting Plate with the arrow up. Make sure the 2 horizontal holes are level.
Secure the Mounting Plate to the Junction Box using the included Junction Box screws.

Tip!
For additional installation instructions, visit: help.lorex.com/W452ASSeries
Wiring & Installation
WARNING
Power wire colors in your home may be different. In such a case, consult a licensed electrician.

Use the Wire Caps to connect the wires.
a. Twist the Ground wire (green) to the ground wire.
b. Twist the Live wire (black) to the live wire.
c. Twist the Neutral wire (white) to the neutral wire.
Carefully fit the wires back into the Junction Box.
Slide the O-Rings onto the Machine Screws, and then use a Phillips-head screwdriver to secure the Mounting Bracket to the Plate.
Ensure the Outer Ring is completely rotated counter-clockwise.
Align the 2 grooves inside the Floodlight to the 2 posts on the inner sides of the Bracket, and then push the Floodlight into place.
Ensure there are no gaps around the perimeter between the Floodlight and Bracket.
Tip! Align the **** to the symbol on the sides.
Twist the Outer Ring clockwise until the and the symbols align.
Tighten the pre-installed locking screw at the bottom of the Mounting Bracket.
Remove the Rubber Plug at the bottom of the Floodlight.
Adjust the camera and LED Panels to the desired position by loosening / tightening the screws on the LED panel arms and the camera.
Turn the power ON at the breaker. If the status indicator does not turn on, check that the wiring is correct.
Add the Floodlight to the Lurex Home app.

Device App Setup

Downloadhttps://app.lorex.com/home/download
Tap

Need help?
For the additional mounting and support material, scan the below QR code or visit:

help.lorex.com/W452ASSeries

Register your product
Please see our full Terms of Service and Limited Hardware Warranty Policy at: orex.com/pages/warranty
Copyright © 2022 Lurex Technology Inc
As our products are subject to continuous improvement, Lurex reserves the right to modify product design, specifications and prices, without notice and without incurring any obligation. E&OE. All rights reserved.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.