Anolis CALUMMA M LED Light Instruction Manual
- June 9, 2024
- ANOLiS
Table of Contents
INSTALLATION INSTRUCTIONS
CALUMMA M / L / XL SC AND MC
CALUMMA M LED Light
QR code for Installations Instructions
https://www.anolislighting.com/resource/calumma-m-l-xl-installation-
instructions
Fixture must be installed by a qualified electrician in accordance with all national and local electrical and construction codes and regulations. This device falls under class one and must be grounded!
STEP 1 CALUMMA INSTALLATION USING YOKE
Use fasteners that are appropriate for use with your mounting surface
1
Drill two holes into the surface according the given dimensions(Calumma M/L/XL)
Fasten the Yoke of the fixture to the surface by two washers, spring washers and screws.
Use an Allen key to release M8 tilting lock on each side of luminaire and adjust tilt of LED module in range of +180°/-180°.
STEP 2 CABLE GLAND INSTALLATION
Slip the cable through the gland according to the picture below and do not
assemble the gland yet.
Use wrench size 22 for cable gland M20x1.5
Strip these lengths for cable connections.
Connection colour coding
Power Connection – colour coding
| L| N| GROUND
---|---|---|---
Core (EU)| Brown| Blue| Green/Yellow
Core (US)| Black| White| Green
STEP 3 CONNECTION – CE
(JUNCTION BOX IS NOT PART OF THE PACKAGE)
A. DALI
Connection – colour coding
WIRE| POWER CONNECTION| WIRE| DATA CONNECTION
Black| L| Red| Data + (+)
White| N| Orange| Data – (-)
Green/Yellow| ****| /| Data 0V (0)
B. DMX
Connection – colour coding
| WIRE | POWER CONNECTION | WIRE | DATA CONNECTION |
|---|---|---|---|
| Black | L | Red | Data + (+) |
| Blue | N | White | Data – (-) |
| Green/Yellow | **** | Shielding | Data 0V (0) |
C. WIRELESS DMX – each fixture
Connection – colour coding
WIRE| POWER CONNECTION| WIRE| DATA CONNECTION
Black| L| Red| Data + (+)
Blue| N| White| Data – (-)
Green/Yellow| ****| Shielding| Data 0V (0)
D. WIRELESS DMX – first fixture
Connection – colour coding
WIRE| POWER CONNECTION| WIRE| DATA CONNECTION
Black| L| Red| Data + (+)
Blue| N| White| Data – (-)
Green/Yellow| ****| Shielding| Data 0V (0)
E. DMX or ETHERNET via E-Box
Connection – colour coding
WIRE| POWER CONNECTION| WIRE| DATA CONNECTION
Black| L| Red| Data + (+)
Blue| N| White| Data – (-)
Green/Yellow| ****| Shielding| Data 0V (0)
F. DMX or ETHERNET via E-Box with Leader and Jumper Cable
Please align the arrow symbol and mate the connector. Do NOT rotate the connector. Correct connection should be signalized by silent „click“ sound.| Mating complete.
UNLOCK
Rotate
NUT 30 degrees anti-clockwise, same as the arrow direction. (Please do not
rotate clockwise during unmating process)
Drop out.
CONNECTION – US
(JUNCTION BOX IS NOT PART OF THE PACKAGE)
A. DALI
Connection – colour coding
| WIRE | POWER CONNECTION | WIRE | DATA CONNECTION |
|---|---|---|---|
| Black | L | Red | Data + (+) |
| White | N | Orange | Data – (-) |
| Green/Yellow | **** | / | Data 0V (0) |
B. WIRELESS DMX – each fixture
Connection – colour coding
| WIRE | POWER CONNECTION | WIRE | DATA CONNECTION |
|---|---|---|---|
| Black | L | Red | Data + (+) |
| White | N | Orange | Data – (-) |
| Green/Yellow | **** | Blue | Data 0V (0) |
C. WIRELESS DMX – first fixture
Connection – colour coding
WIRE| POWER CONNECTION| WIRE| DATA CONNECTION
Black| L| Red| Data + (+)
White| N| Orange| Data – (-)
Green/Yellow| ****| Blue| Data 0V (0)
D. DMX or ETHERNET via E-Box
Connection – colour coding
WIRE| POWER CONNECTION| WIRE| DATA CONNECTION
Black| L| Red| Data + (+)
White| N| Orange| Data – (-)
Green/Yellow| ****| Blue| Data 0V (0)
STEP 4
CABLE GLAND INSTALLATION
Assemble the cable gland according to the picture.
Use wrench size 22 for cable gland M20x1.5
Install Cable glands individually!
We recommend to apply an adequate layer of the paste LOCTITE 5331 on the
plastic holder of the cable gland before inserting in into the body of the
gland and an adequate layer of the paste LOCTITE 577 on the thread of the
gland body.
Failure to properly install cable glands will result in failure of the
water tight seal!
STEP 5
INSTALLATION OF ACCESORIES
Screw-out
4 screws from the cover plate.
Remove the
cover plate.
Place the
accessories (TO PHAT, HALF TO PHAT, OPTICAL DEMO SET) onto luminaire and
centre it.
Fasten the
accessories (TO PHAT, HALF TO PHAT, OPTICAL DEMO SET) to the luminaire by the
4 packed-in washers and screws.
Slide the
Optical foil into the space of Optical Demo Set.
Place the
luminaire on tenon on the Floor Stand.
The Luminaire fasten by one washer one flexible washer and one nut closed.
Installation on FLAT POLE with two screws.
Installation on POLE (diameter 76-116mm) with zip ties.
Maximum width zip ties is 20mm (not included packing).
Drill three holes into the surface according the given dimensions.
Insert the cable gland into the middle hole.
Fasten the
Pole Adaptor on the surface by two screws, spring washers and washers.
Fasten the Luminaire on the Pole Adaptor by three screws, spring washers and washers.
Fasten the
Pole Adaptor on the surface by two screws, spring washers, washers and
spacers.
Fasten the
Luminaire on the Pole Adaptor by three screws, spring washers and washers.
Installations Pole Adaptor with two zip ties.
Fasten the Luminaire on the Pole Adaptor by three screws, spring washers and washers.
FOR ALL INSTALLATION VERSIONS
Pull the cable through the inside of the Pole Adaptor and the cable gland and return to STEP 3.
ROBE lighting s. r. o.
Palackeho 416/757 01 Valasske Mezirici
Czech Republic
Tel.: +420 571 751 500
E-mail: info@anolis.eu
www.anolislighting.com
VERSION 3.0 / 2_2023
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>