TUNZE 8821 LED White Eco Chic Instructions

June 4, 2024
TUNZE

TUNZE 8821 LED White Eco Chic

TUNZE-8821-LED-White-Eco-Chic-
pro

General information / technical data

TUNZE® LED marine eco-chic 8811
Suitable for stony coral aquariums up to approx. 20 liters (5.3 USgal.) and soft coral aquariums up to approx. 40 liters (10.6 USgal.). Equipped with 15 white LEDs (6.500 K) and 15 blue LEDs (455 nm). Can be used in the air and underwater. Color temperature: approx. 25,000 K Perceived brightness: 410 lmPhotosynthetically Active Radiation Flux (PAR): 3 W Photosynthetic photon flux: 12.0 µmol / s Power consumption: 10 W Power supply: 100-240V/50-60Hz Including Magnet Holder for a glass thickness up to 10 mm (3/8“).

Dimensions without the bracket (l x w x h):

  • 305 x 25 x 13 mm (12 x 0.98 x 0.66 in.)
  • Cable length: 1.5 m (59 in.)
  • This lamp contains built-in LED bulbs.
  • The bulbs in the lamp can not be replaced.
  • This lamp is intended exclusively for illuminating aquariums!

General information / technical data

TUNZE® LED white eco-chic 8821
Suitable for soft coral aquariums to approx. 40 liters (11 USgal.) and freshwater aquariums up to approx. 60 liters (16 USgal.).

  • Equipped with 30 white LEDs.
  • Can be used in the air and underwater.
  • Color temperature: > 13,000 K
  • Perceived brightness: 700 lm
  • Photosynthetically Active Radiation Flux (PAR): 3 W Photosynthetic photon flux: 12.8 µmol / s
  • Power consumption: 10 W
  • Power supply: 100-240V/50-60Hz
  • Including a Magnet Holder for a glass thickness up to 10 mm (3/8“).
  • Dimensions without the bracket (l x w x h):305 x 25 x 13 mm (12 x 0.98 x 0.66 in.)
  • Cable length: 1.5 m (59 in.)
  • This lamp contains built-in LED bulbs.
  • The bulbs in the lamp can not be replaced.
  • This lamp is intended exclusively for illuminating aquariums!

General information / technical data TUNZE® LED eco chic refugium 8831

  • Spectrum is especially suitable for refuge and basin for algae growth in seawater and plant growth in freshwater. Can be used in the air and underwater.
  • Photosynthetically Active Radiation Flux (PAR): 2.22 W Photosynthetic photon flux: 10.1 µmol / s
  • Power consumption: 9 W
  • Power supply: 100-240V/50-60Hz
  • Including a Magnet Holder for a glass thickness up to 10 mm (3/8“).
  • Dimensions without the bracket (l x w x h):  305 x 25 x 13 mm (12 x 0.98 x 0.66 in.)
  • Cable length 1.5 m (59 in.).
  • This lamp contains built-in LED bulbs.
  • The bulbs in the lamp can not be replaced.
  • This lamp is intended exclusively for growing algae and plants!
General information / technical data

TUNZE® LED full spectrum 8850

  • Suitable for stony coral aquariums up to approx. 40 liters (11 USgal.), soft coral aquariums up to approx. 60 liters (16 USgal.), and freshwater aquariums up to approx. 80 liters (21 USgal.). Active power control for more power when used underwater. Cold white, blue, green and red LEDs for an adjustable light spectrum from> 13,000 K to pure blue light. Manual setting with magnet holder or separately available Multicontroller 7097 or SmartController 7000.
  • Color temperature: approx. 30,000 K
  • Perceived brightness: 400 lm
  • Photosynthetically Active Radiation Flux (PAR): 2.2 W Photosynthetic photon flux: 9.2 µmol / s
  • Power consumption: 9,5 W | Power supply: 100-240V/50-60Hz This lamp can also be used permanently under water (improved cooling), where it achieves a maximum performance of 26 W in the case of all LEDs are set to max. brightness (about 30,000 K). When operated in the air, the lamp adjusts itself to about 9.5 W. Including Magnet Holder for a glass thickness up to 12 mm (1/2“).
  • Dimensions without the bracket (l x w x h):
  • 305 x 25 x 17 mm (12 x 0.98 x 0.66 in.)
  • Cable length 2.5 m (98.4 in.).
  • This lamp contains built-in LED bulbs.
  • The bulbs in the lamp can not be replaced.
  • This lamp is intended exclusively for illuminating aquariums!

Sunrise function only for LED full spectrum 8850

After inserting the full spectrum LED, it will automatically simulate a sunrise that lasts 100 seconds. The sunrise will end with the color combination, which was set during the manual adjustment (see „Manual adjustment“). The sunrise feature will be disabled through the connection of the Multicontroller 7097 / SmartController 7000.

Safety instructions

  • Looking directly into the Tunze® LED can harm the eyes. Therefore, protect the eyes from glare! (1)
  • Do not shine the Tunze® LED onto a reflective surface. Only use the Tunze® LED indoors. Outdoor operation is not permitted.
  • Only operate the Tunze® LED 8811, 8821 and 8831 with the original TUNZE® power supply unit 5012.010 (12 V)!
  • Only operate the Tunze® LED 8850 with the original TUNZE® power supply unit 6095.240 (24 V)!
  • Only position the power supply in a dry and well-ventilated place!
  • Do not place it near heat sources of any kind (2).
  • The ambient temperature should not exceed 35°C (3).
  • Do not fold the cable.
  • Before commissioning, check that the operating voltage corresponds to the mains voltage.
  • Do not connect to external devices.
  • Please retain the instruction manual for future reference.
  • This device is suitable for users (including children) with limited physical, sensorial or mental abilities or without any experience or previous knowledge if suitable supervision or detailed instructions on the operation of the device is provided by a responsible person. Please make sure that children do not play with the device (4).

Safety instructions for the magnet holder

  • Very strong magnet! (7)
  • Keep the magnet holder out of reach of children!
  • Caution! Risk of injury! (8)
  • Do not bring the magnet halves together! The magnet halves cling together with a force of approx. 30 to 200 kg (66 to 441 lbs.), depending on the type of direct contact.
  • Only touch the magnetic parts on the sides with your hand. Never place the hand or the fingers between the contact surfaces (9)!
  • The magnets attracts metal parts and other magnets which are less than 10 cm (3.94 in.) away with great force! When handling the magnet, no metal parts, other magnets, blades or knives should be
  • within a vicinity of 10 cm (3.94 in.) in order to avoid injuries.
  • Beware of magnetically sensitive items such as pacemakers, data carriers, credit cards and keys. Maintain a minimum distance of at least 30 cm (10.92 in.)!
  • When transporting the Magnet Holder, always use the supplied spacer adapter.
  • Heating above 50°C (122°F) will lead to the destruction of the magnet, or loss of the magnetic effect (10).

Safety instructions for TUNZE® power supply units

  • TUNZE® power supply units have not been designed for outdoor operation (1).
  • In order to prevent water damage, the power supply unit should be placed as far away from the aquarium as possible.
  • Operation is permitted only with a residual-current-operated circuit-breaker fitted, max. 30 mA.
  • Before working in the aquarium, please make sure that all electric units in use have been disconnected from the mains.
  • Do not repair a damaged mains cable – replace the unit completely.
  • The connections at the cable ends are susceptible to water and may be destroyed in case of water damage!
  • Mount the power supply unit in a dry and well-ventilated position only.
  • Do not mount in the vicinity of heat sources (2). Ambient temperature during operation: 0°C to +35°C (32°C to 95° F)
  • Ambient humidity during operation: 30% – 90%Storage temperature: -25°C to +80° Celsius (-13°F to 176°F) Storage humidity: 30% – 95%

Magnet Holder preparation and attachment
CAUTION!
Prepare the magnets individually and place them far apart from each other to avoid injuries.

  • For utilization of LED full spectrum 8850 with glass thicknesses up to 15 mm (2/3“), replace the white holder magnets of the lamp with the black holder magnets of the separately available Magnet Holder 6025.500.
  • For LED marine eco-chic 8811, LED white eco-chic 8821 and eco-chic refugium 8831, the retention force will be increased from 10 mm (3/8“) to 12 mm (1/2“) by Magnet Holder 6025.515.
  • Prepare a suitable place on the glass pane, whereas the outside should be clean and dry.
  • Attach the magnet with the bracket for the LED lamp with the magnetic suction ring facing in the direction of the inner aquarium glass pane (1).
  • Position the holder magnet (2) of the Magnet Holder towards the inner part (1) and then carefully bring them together.
  • There are two different mounting options available:
  • As shown in Fig. (3), the lamp can be installed centered in the holder, or with the cable end towards the glass pane as shown in Fig. (4).
  • To move the Magnet Holder to a different position, the external holder magnet should be slightly lifted from the glass.

Commissioning LED marine eco-chic 8811, LED white eco-chic 8821 and LED eco chic refugium 8831Insert the barrel connector of the AC adapter into the plug on the cable end of the lamp, then plug AC adapter into a mains socket. The lamp can be operated above (1) or underwater (2) with consistent electrical power consumption. This underwater lighting avoids light reflections on the water surface, which makes this lighting source even more efficient and brighter. An immersion depth of 1 to 2 cm (0.39 to 0.78 in.) is sufficient. The lamp consists of a protective encapsulated construction and is corrosion resistant with no harmful effects for your aquarium biotope. After a prolonged operation underwater, the light-emitting side becomes slightly opaque.

Commissioning LED full spectrum 8850
Insert the barrel connector of the AC adapter into the plug on the cable end of the lamp, then plug AC adapter into a mains socket. The lamp can be operated above (1) or underwater (2).

Above the water surface:
The LED full spectrum will regulate itself to a temperature of approx. 50°C (130°F) even if it‘s operated non-submerged. At room temperature, it will thereby have a power consumption of 10 W regardless of the color setting. Moving or cool air will increase the performance, heat build-up will reduce it.

Below the water surface:
This underwater lighting avoids light reflections on the water surface, which makes this lighting source even more efficient and brighter. An immersion depth of 1 to 2 cm (0.39 to 0.78 in.) is sufficient. The lamp consists of a protective encapsulated construction and is corrosion resistant with no harmful effects for your aquarium biotope. During the operation in aquarium water, the lamp is cooled sufficiently, and will only reach the maximum power of 26 W if all the LEDs are set to the maximum brightness. After a prolonged operation underwater, the light-emitting side becomes slightly opaque

Cleaning

Never remove dirt using hard or abrasive objects!When operating above the water surface, the light may be cleaned by briefly rinsing it with tap water and then drying it thoroughly with a soft cloth. When operating the lamp below the water surface, we recommend cleaning on a regular basis, at least once a year. Under unfavorable conditions, shorter intervals (approximately every three months) are necessary. Never remove dirt using hard objects! To remove calcium or other deposits soak the light in vinegar and rinse briefly with fresh water.

Manual control only for LED full spectrum 8850
The light color can be set with the supplied holder magnets. Hold the LED light with one hand and loosen the holder magnet from the aquarium glass pane. Now, raise the holder magnet (1) on the front of the LED lamp (2) and vary its position slowly until you notice a change in the light color. As long as the magnet is in position, the light color cycle through an infinite settings loop (3) from white to deep blue light. In the delivery state (4) all LEDs are set to the maximum brightness. This is indicated by a short blinking during the procedure.As soon as you remove the holder magnets the light color will be stored permanently. The TUNZE® LED (1) has a built-in temperature monitoring. In case of insufficient ventilation/cooling, the light output/brightness will be reduced.
The information about the color temperatures are approximations based on a comparable thermal radiator.

Connection to Multicontroller 7097 / SmartController 7000 only for LED full spectrum 8850
With the Multicontroller 7097 / SmartController 7000 it is possible to control all color channels individually and time-dependent. For this, the Multicontroller 7097 / SmartController 7000 must be connected to the lamp with a 5-pin connector cable and to a power supply. Through this connection to the LED, the ramping function during startup will be switched off!

Other power supply units for all Tunze® LEDs – Safety Connector
The Tunze® LEDs 8811, 8821 and 8831 can be operated with any direct-current source (battery, solar cells) from 8 to 12 V.The Tunze® LED full spectrum 8850 can be operated with any direct-current source (battery, solar cells) from 20 to 24 V.For a safe connection, we recommend using the Safety Connector item no. 6105.500 (1) which contains a 4 A fuse. The Safety Connector enables a normal operation with the TUNZE® power supply unit (2), but in case of a power failure it will automatically switch over to a battery (3) or a DC power source. It should always be ensured that the battery is in optimal condition, by using a commercially available battery charger.Observe the maximum DC voltage of 12 V resp. 24 V!Tube Magnet Holder 8850.500The Tube Magnet Holder 8850.500 can be ordered separately as a spare part.

Warranty

The unit manufactured by TUNZE® Aquarientechnik GmbH carries a limited guarantee for a period of twenty-four (24) months after the date of purchase covering all defects in material and workmanship. Within the framework of the corresponding laws, your remedies in case of a violation of the guarantee obligation shall be limited to returning the unit manufactured by TUNZE® Aquarientechnik GmbH for repair or replacement at the discretion of the manufacturer. Within the framework of the corresponding laws, the said shall be the only remedies. Consequential damage and/or other damage shall be excluded therefrom explicitly. Defect units shall have to be shipped to the dealer or the manufacturer in the original packaging together with the sales slip in a pre-paid consignment. Unpaid consignments will not be accepted by the manufacturer. Exclusion from guarantee shall exist also in case of damage caused by inexpert handling (such as water damage), technical modification carried out by the buyer or by connection to devices that have not been recommended. Subject to technical modifications, especially those which further safety and technical progress. Customers in USA, please refer to seperate Limited Warranty for United States brochure.

Disposal
The device and the battery may not be disposed of in normal domestic waste; it has to be disposed of in an expert manner. Important for Europe: Devices can be disposed of through your community’s disposal area.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals