MikroTik RBLDF-5nD Outdoor Access Point User Guide

: June 13, 2024
: Mikrotik

Table of Contents

Quick Guide G3
73782, #73875, #73876
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Quick Guide G3

Models: RBLDF-5nD (LDF 5), RBLDFG-5acD (LDF 5 ac), RBSXTsq5HPnD (SXTsq 5), RBSXTsqG-5acD (SXTsq 5 ac), RBSXTsq5nD (SXTsq Lite5), RBDiscG5acD (DISC Lite5 ac), RBDisc-5nD (DISC Lite5), RBLHG-5nD (LHG 5), RBLHG-5HPnD (LHG HP5), RBLHGG-5acD (LHG 5 ac), RBLHGG-5acD-XL (LHG XL 5 ac), RBLHG-5HPnD-XL (LHG XL HP5)

Quick Guide:

This device needs to be upgraded to RouterOS v7.7 or the latest version to ensure compliance with local authority regulations!

It is the end users’ responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling requirements, and Dynamic Frequency Selection (DFS) requirements. All MikroTik radio devices must be professionally installed.

This is a Wireless Network Device. You can find the product model name on the case label (ID).

Please visit the user manual page on https://mt.lv/um for the full up-to- date user manual, or scan the QR code with your mobile phone.

The most important technical specifications for this product can be found on the last page of this Quick Guide.

Technical specifications, brochures, and more info about products is found on https://mikrotik.com/products

Configuration manual for software in your language with additional information can be found at https://mt.lv/help

MikroTik devices are for professional use. If you do not have qualifications, please seek a consultant https://mikrotik.com/consultants

Depending on the antenna used, you must set its gain. This is to ensure that EIRP meets the limit set by the local authorities. This is done in the WebFig Quickset menu.

First steps:

Connect the device to the included PoE injector with an Ethernet cable;
Connect the PoE injector into the PC;
Connect the power adapter to the PoE injector;
Download WinBox configuration tool https://mt.lv/winbox;
Open WinBox and connect to the device;
admin alsoNeighbors tab and connect to the device MAC address;
Download the latest RouterOS software from https://mikrotik.com/download;
Choose MIPSBE packages or ARM for LHG ac, and save them to your PC;
Open WinBox and upload downloaded packages, drag and drop into any windows;
Restart the device and Reset the wireless interface;
Connect again and in the QuickSet menu set your Country, to apply country regulation settings;
Secure your device and set a strong password.

Safety Information:

Before you work on any MikroTik equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing accidents. The installer should be familiar with network structures, terms, and concepts.
Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.
This equipment is to be installed by trained and qualified personnel, as per these installation instructions. The installer is responsible for making sure, that the Installation of the equipment is compliant with local and national electrical codes. Do not attempt to disassemble, repair, or modify the device.
This product is intended to be mounted outdoors on a pole. Please read the mounting instructions carefully before beginning installation. Failure to use the correct hardware and configuration or to follow the correct procedures could result in a hazardous situation for people and damage to the system.
We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your own risk!
This is a Class A product. In a domestic environment, this product might cause radio interference in which case the user might be required to take adequate measures.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power adapter from the power outlet.

Exposure to Radio Frequency Radiation: This MikroTik equipment complies with the FCC, IC, and European Union radiation exposure limits set forth for an uncontrolled environment. This MikroTik device should be installed and operated no closer than 40 centimeters from your body, occupational user, or the general public.

Manufacturer: Mikrotikls SIA, Unijas iela 2, Riga, Latvia, LV1039.

Note: For some models, check the user and wireless passwords on the sticker.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit to ensure compliance.

Antenna Installation WARNING: It is the installer’s responsibility to ensure that when using the authorized antennas in the USA (or where FCC rules apply); only those antennas certified with the product are to be used. The installer should configure the output power level of antennas, according to country regulations and per antenna type. Professional installation is required for equipment with connectors to ensure compliance with health and safety issues.

LIST OF APPROVED 5 GHz ANTENNAS:

27 dBi Parabolic Dish Antenna (MikroTik model: LHG XL-5)
24.5 dBi Parabolic Dish Antenna (MikroTik model: LHG-5)
21 dBi Parabolic Dish Antenna (MikroTik model: Disc-5)
16 dBi Dual Polarity, Directional Antenna (MikroTik model: SXTsq-5)
9 dBi Dual Polarity, Directional Antenna (MikroTik model: LDF-5)
The same type of antenna and lower antenna gain than those listed above may also be used in accordance with certification.

Innovation, Science and Economic Development Canada

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

This Class A digital apparatus complies with Canadian ICES-003.

CAN ICES-003 (A) / NMB-003 (A)

The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.

Antenna Installation WARNING: It is the installer’s responsibility to ensure that when using the authorized antennas in Canada (or where IC rules apply); only those antennas certified with the product are to be used. The installer should configure the output power level of antennas, according to country regulations and per antenna type. Professional installation is required for equipment with connectors to ensure compliance with health and safety issues.

LIST OF APPROVED 5 GHz ANTENNAS:

27 dBi Parabolic Dish Antenna (MikroTik model: LHG XL-5)
24.5 dBi Parabolic Dish Antenna (MikroTik model: LHG-5)
21 dBi Parabolic Dish Antenna (MikroTik model: Disc-5)
16 dBi Dual Polarity, Directional Antenna (MikroTik model: SXTsq-5)
9 dBi Dual Polarity, Directional Antenna (MikroTik model: LDF-5)
The same type of antenna and lower antenna gain than those listed above may also be used in accordance with certification.

UKCA marking

CE Declaration of Conformity

Hereby, Mikrotkls SIA declares that the radio equipment type RouterBOARD is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://mikrotik.com/products

WLAN

Operating Frequency / Maximum output power	5470-5725 MHz / 27 dBm

This MikroTik device meets Maximum TX power limits per ETSI regulations. For more detailed information see Declaration of Conformity above

The WLAN function for this device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range only for RBSXTsq5HPnD, RBLHG-5HPnD and RBLHG-5HPnD-XL.

|

AT

| BE | BG| CH| CY| CZ| DE
---|---|---|---|---|---|---|---
DK| EE| EL| ES| FI| FR|

HR

HU

| IE| IS| IT| LI| LT| LU
LV| MT| NL| NO| PL| PT|

RO

SE

| SI| SK| TR|

UK(NI)

| |

Technical Specifications

Product Power Input Options| DC Adapter Output Specification| IP class of the enclosure| Operating Temperature
---|---|---|---
PoE In Ethernet
Port (10 – 30 V)| Input: 100-240 V AC
Output: 24 V DC, 0.38A| IP54
IP55
(RBSXTsq5HPnD,
RBSXTsqG-5acD,
RBSXTsq5nD)| -40°..+70°C

Please, test your antenna with our device in accreditation laboratory to be in compliance with EU rules.