Tunze 7000.001 Smart Controller Instruction Manual
- June 16, 2024
- TUNZE
Table of Contents
- 7000.001 Smart Controller
- General aspects
- Technical data
- Safety instructions
- Safety instructions for magnet holder
- Safety instructions for TUNZE® power supply units
- Fitting Magnet Holder
- Initial operation applicable for all Turbelle ® stream
- Initial operation applicable only for 6105 eco and 6255 eco
- Other power supply units for 6105 eco and 6255 eco – safety connector
- Short description of the display
- Commissioning / settings
- Turbelle ® controller as MASTER with additional pumps as SLAVE
- Night mode / Moonlight
- Detaching the pump cable
- Cable guard 6040.019
- Arrangement examples in aquariums
- Servicing
- Illustration of parts
- Warranty
- Disposal
- Documents / Resources
stream
6065, 6085
6125
6105 eco
6255 eco
x6105.8888
07/2023
7000.001 Smart Controller
General aspects
Turbelle® stream is a spherical propeller pump used to circulate water in
fresh or salt water aquariums as well as in tanks. It is based on the latest
state of the art in technology and offers very high reliability requiring less
servicing and current consumption. The extraordinary design, which includes a
magnet holder and a silence clamp, permits 3D adjustment (1) and an
uncomplicated attachment at every point of the aquarium pane.
Turbelle ® stream 6065, 6085 and 6125 convince with their price-performance
ratio keeping a consistent performance.
Turbelle® stream 6105 eco and 6255 eco (2) can be controlled electronically
and ha e been provided with a fish-care function. These pumps can also be
controlled by means of a SmartController7000.001 and are supplied with a
12V/24 V power supply unit
Technical data
Turbelle® stream 6065 for aquariums from 250 to 800 liters (66 to 211 USgal.)
Flow rate: about 6,500 l/h (1,717 USgal./h)
Energy consumption: 12 W
Voltage / frequency: 230V/50Hz (115V/60Hz)
Cable length: 2 m (78.7”)
Dimensions: diam. 90 mm (3.5”), Output: diam. 50 mm (1.96”)
Magnet Holder up to a glass thickness of 15 mm (2/3”)
Turbelle® stream 6085 for aquariums from 400 to 1,000 liters (105 to 264
USgal.)
Flow rate: about 8,000 l/h (2,113 USgal./h)
Energy consumption: 14 W
Voltage / frequency: 230V/50Hz (115V/60Hz)
Cable length: 2 m (78.7”)
Dimensions: diam. 90 mm (3.5”), Output: diam. 50 mm (1.96”)
Magnet Holder up to a glass thickness of 15 mm (2/3”)Turbelle® stream 6125
WIDE FLOW for aquariums from 400 to 2,000 liters (105 to 528 USgal.)
Flow rate: about 12,000 l/h (3,170 USgal./h)
Energy consumption: 22 W
Voltage / frequency: 230V/50Hz (115V/60Hz)
Cable length: 2 m (78.7”)Dimensions: diam. 90 mm (3.5”), Output: diam. 63
mm (2.4”)
Magnet Holder up to a glass thickness of 15 mm (2/3”)Turbelle ® stream eco
6105.002 for aquariums from 200 to 2,000 liters (53 to 528 USgal.)
Flow rate: approx. 3,000 to 12,000 l/h (793 to 3,170 USgal./h) at 12 V
Energy consumption: max. 3-11 W at 12 V
Energy consumption: 11 W at 12,000 l/h (3,170 USgal./h)
Power supply unit: 100–240V / 50–60Hz
Cable length: 5 m (196.8”) up to the controller
Dimensions: ø90 mm (3.5”)
Output: ø63 mm (2.48”) and ø75 mm (3”)
Magnet Holder with Silence clamp up to a glass thickness of 15 mm (2/3”)
Including second propeller housing for best protection.Turbelle® stream eco
6255.002 for aquariums > 2.000 liters (528 USgal.)
Flow rate: 5,000 to approx. 17,000 l/h at 24 V (1,321 to 4,491 USgal./h)
Energy consumption: max. 10-31 W at 24 V
Energy consumption: 31 W at 17,000 l/h (4,491 USgal./h)
Power supply unit:100-240V / 50-60Hz
Length of cable: 5 m (196.8”) up to the controller
Dimensions: ø90 mm (3.5”)
Output: ø63 mm (2.48”) and ø75 mm (3”)
Magnet Holder with Silence clamp up to a glass thickness of 27 mm (1”).
Including second propeller housing for best protection.
Safety instructions
Only operate the pump fully immersed.
Only place the pump into the aquarium. An operation outdoors is only allowed
with a 10 m (32.8 ft.) rubber cable (1).
The pump may not be used in swimming pools.
Prior to initial operation, please check whether the operating voltage
corresponds to the mains voltage available.
In order to avoid water damage in the plugs, the mains plug should be fitted
at a higher lever than the unit (2).
Operation is permitted only with a residual-current-operated circuit-breaker
fitted, max. 30 mA.
Before working in the aquarium, please make sure that all electric units used
have been disconnected from the mains.
Do not repair a damaged mains cable – replace the pump completely.
Temperature of the aquarium water: maximum +35° Celsius (95° F) (3).
The connection to devices, such as electronic switches or speed controllers,
of other makes is not permissible (4)!
This device is suitable for users (including children) with limited physical,
sensorial or mental abilities or without any experience or previous knowledge,
if suitable supervision or detailed instructions on the operation of the
device is provided by a responsible person.
Please make sure that children do not play with the device (5).
Keep the instruction manual in a safe place.
Safety instructions for magnet holder
Very strong magnet! (1)
Keep the magnet holder out of reach of children!
Caution! Danger of injury! (2)
Do not bring upper and lower magnet part together directly! Depending on the
type, the parts of the magnet cling together on direct contact with about 30
to 200 kg (66 to 441 lbs.).
Get hold of the magnet parts at the sides only; never get your hand or fingers
between the contract surfaces (3)!
Attracts metal parts and other magnets with a large force at a distance of
below 10 cm (3.9 in.) ! When handling the magnet, no metal parts, other
magnets, blades or knives should be located closer than 10 cm (3.9 in.) in
order to avoid injuries.
Exercise caution in case of magnetically sensitive objects, such as
pacemakers, data carriers, credit cards and keys – keep a distance of at least
30 cm (11.8 in.)!
Always use the piece of polystyrene supplied when transporting the Magnet
Holder. (4)
Heat of more than 50° Celsius (122° F) will lead to the destruction of the
magnet or the loss of the magnetic action (4).
Safety instructions for TUNZE® power supply units
TUNZE® power supply units have not been designed for outdoor operation (1).
In order to prevent water damage, the power supply unit should be placed as
far away from the aquarium as possible.
Operation is permitted only with a residual-current-operated circuit-breaker
fitted, max. 30 mA.
Before working in the aquarium, please make sure that all electric units in
use have been disconnected from the mains.
Do not repair a damaged mains cable – replace the unit completely.
The connection to devices, such as electronic switches or speed controllers,
of other makes is not permissible (2)!
The Turbelle Controller on the pump cable is susceptible to water and may be
destroyed in case of water damage!
The operation of the Turbelle pumps is permissible only with the original
TUNZE ® power supply unit.
Mount the power supply unit in a dry and well-ventilated position only.
Do not mount in the vicinity of heat sources (3).
Ambient temperature during operation: 0° Celsius (32° F) to +35° Celsius (95°
F)
Ambient humidity during operation: 30% – 90%
Storage temperature: -25° Celsius (-13° F) to +80° Celsius (176° F); Storage
humidity: 30% – 95%
Fitting Magnet Holder
CAUTION! Prepare magnets separate from each other, and place them far
away from each other, as otherwise there is a danger of injury.
Remove the elastic buffers from the film (1) and press them on to the spot
provided for the purpose (2). Use four buffers for each part of the magnet. As
shown in the illustration (3), the adhesion points are in the round cavities
provided for the purpose.
The Magnet Holders are only designed for use in filled aquariums. If the
devices are mounted while the tank is not filled with water, the holding force
might be too low.
If used with the max. recommended pane thickness, only limited 3D-setting is
possible, as the lateral tensile forces might be too high. If adjusted at an
angle of more than 30° to 40° to the direction of flow, a Magnet Extension
might be required to ensure safe installation.
Accessories: Magnet Extension 6205.501 (4) increases the holding power of the
Magnet Holder 6105.515 for use with a glass thickness up to 20 mm (3/4“).
Initial operation applicable for all Turbelle ® stream
Mount the silence clamp: For this purpose, press the base plate (1) on one of
the two magnets (2) (apply a rubber hammer, if and when required); press four
silicone buffers (3) into the base plate (2), and the clamp (4) on to the
silicone buffer.
Prepare a suitable position on the glass pane. The glass pane should be free
from algae inside the aquarium, and should be dry and clean on the outside.
(The outside part of the magnet holder is as waterproof as its inside part,
consequently it can also be attached under water, e.g. when used on drainage
shafts / overflow installations, in filter tanks, etc.)
Fit the inside parts of the magnet holder to the aquarium pane with the
elastic buffer pointing in direction of the glass (5).
Hold the outside part of the magnet holder to the inside part (6), and then
carefully bring together.
In order to move the magnet holder into another position without damaging the
elastic buffer, the outside magnet should be slightly lifted away from the
glass.
Clip the pump into the clamp (7) and set the requested direction of flow.
In the case of non-electronic versions in particular, we recommend the use of
the protective grating (8) supplied in order to prevent smaller fish and
crayfish from getting into the outlet of the pump.Using
the pump on panes with maximum glass thickness the 3D-adjustment of the magnet
holder is limited due to increasing lateral tractive forces. A safe mounting
could make requirable a Magnet Extension in case of shifting exceeds 40° – 50°
(9).
It‘s not permitted to connect the pump to external device!
Initial operation applicable only for 6105 eco and 6255 eco
Plug the connector (1) from the power supply 6101.240 / 3154.120 (2) into the
appropriate socket (3) on the
Turbelle ® controller (4), then connect the power supply the plug (5).
An additional pump with controller (6) or a SmartController 7000.001 (7) can
be connected to the upper socket of the
Turbelle® controller.
More detailed connection information for the SmartController 7000.001 can be
obtained from the espective instruction manual.
Automatic shut-down:
The pump will be stopped immediately in case of blockage or if the system runs
dry. After the blockage has been removed, the pump will start up automatically
after a delay of 30 seconds. The pump control is thermally protected. The
power supply unit is protected against short-circuit and thermal
overload.
Other power supply units for 6105 eco and 6255 eco – safety connector
Turbelle® stream 6105 eco and 6255 eco are pumps with an electronic motor.
Thus, they can be operated on any direct-current source (battery, solar cells)
from 10 V to 24 V. For a safe connection of the pump, we recommend the
Turbelle® safety connector (article No. 6105.500 (1), which contains a 4 amps
fuse. The safety connector permits normal operation with the TUNZE® power
supply unit (2), but in case of a power failure it will automatically switch
over to a battery (3) or a direct-current source.
Always ensure a correct charge condition of the battery by using a
commercially available charger. Indoor use of lead starter batteries for cars
is inadmissible!
Never connect the Turbelle® stream 6105 eco and 6255 eco to a battery or a
direct-current source directly and without fuse.
Maximum direct-current source permissible 27.5 Volt (cut-off limit); above 45
Volt the electronic system will be destroyed.
Turbelle® controller
The Turbelle® controller is a device which is used to set the variable pump
performance. It can provide a wave simulation, oscillation flow, an automatic
search for the resonance frequency when the oscillation flow is used, and it
is also equipped with a food timer. It can be directly connected to a
SmartController 7000.001. The pump is therefore able to operate together with
other pumps, for example, in the high/low tide mode. If the Moonlight 7097.050
(not included in the scope of delivery) is attached to the Turbelle ®
controller, the night-mode operation will be activated automatically. If this
controller is connected to a second controller with the 7092.300 cable, a
further pump can be connected and controlled, for example, to provide a wave
pounding simulation or an oscillating current. A third controller can be added
using the Y-adapter cable 7090.300.
Short description of the display
Button “food timer” (1)
The “food timer” button switches the pump off and on, allowing the fish to
feed in peace and quiet, whereas the pump will automatically switch on again
after approx. 10 minutes unless the “food timer” was manually activated
through an actuation of the respective button.
Control knob “main power” (2)
The main performance of the pump can be adjusted with this control knob.
“Select” button (5) Various programs can be selected with this button:
“pulse 2-10 s” (6) Pulse operation for biologically active current pulses
(wave motion), in the range of 2-10 seconds. “auto adjust” (7)
Automatic and easy searching for the perfect resonance frequency for the
Turbelle pump or Wavebox.
“wave ok” (8)
The “auto adjust” (7) is suspended by briefly pressing on the “select” button
(5). The pulse frequency can also be fine-tuned manually with the control knob
(3).
“external control” (9) – SmartController 7000.001
This setting is required for a connection to a SmartController 7000.001 or to
another TUNZE controller. If the external controller is not connected, or it
doesn’t provide a control signal the pump will be switched off. The pump can
still be set with the “main power” control knob (2) to specify the maximum
performance.
However, we recommend to set this “main power” control knob (2) to full power
every time! The setting button “pulse” (3) is without effect, because the
controller can now be controlled externally.
Control knob “pulse” (3) Controlling of the Turbelle pump for wave simulation.
The performance will vary in a pulse cycle of 2 to 10 seconds, between the two
performance levels specified with the control knobs “main power” (2) and
“pulse power” (4). In the “off” position the pulse is switched off and the
pump will operate with a constant performance which was only set with the
“main power” (2) button.
Control knob “pulse power” (4) The second performance level of the pump, is
active during a pulse operation or the night mode.
Commissioning / settings
Factory setting: for “select” the setting “pulse 2-10 s” (6) is switched on,
and the control knobs “main power” (2) and “pulse power” (4) are set to
approx. 80%. Control knob “pulse” is set to “off”.
“pulse 2-10 s” (6)
Press the “select” (5) button until “pulse 2-10 s” (6) lights up. If the
control knob “pulse” (3) is turned it will light up, and the pump will pulse
within the preset cycle of 2-10 s between the performance levels “pulse power”
(4) and “main power” (2).
“auto adjust” (7)
Set the control knobs “pulse power” (4) to “off” and “main power” (2) to
“100%”.
Turn the control knob (3) to the center position.
Press the “select” (5) button until “auto adjust” (7) lights up. After three
seconds an automatic and easy searching for the perfect resonance frequency
for the Turbelle pump or Wavebox will be started. The pulsing will then start
at a cycle of 0.3 seconds and increase every second in an interval of 0.01
seconds to the highest value of 2.0 seconds.
During this time, the aquarium should be closely observed. A
water movement will be detectable, once the resonance frequency is reached.
The “auto adjust” function (7) can then be stopped again by briefly pressing
the “select” button (5), which will cause “wave ok” (8) to light up.
You can carry out an additional fine adjustment with the control knob “pulse”
(3) now.
Before the “auto adjust”, we recommend positioning this control knob (3) to
the center position.
The controller will remember the adjusted time. If someone accidentally
presses the “select” button, the function “wave ok” can be selected again with
the “select” button (5). Hereby, it must be observed not to remain on the
“auto adjust” function for more than 3 seconds, because otherwise the stored
value will be deleted. After 3 seconds, the “auto adjust” function will always
restart with a new initial value of 0.3 seconds.
Turbelle ® controller as MASTER with additional pumps as SLAVE
With the cable 7092.300, the Turbelle ® controller (1) can control another
Turbelle® pump (2) simultaneously. In this case the first pump with the
associated Turbelle controller (1) is referred to as MASTER; the various
settings are made on this controller. The second pump (2) is called SLAVE and
its Turbelle controller should be set to “external control”, while the “main
power” knob remains active. This is also possible with the Y-adapter cable
7090.300, however this will enable the additional connection of the Moonlight
7097.050 (3) or a third pump.
Turbelle® controller in the inverse operation (4):
If a second Turbelle pump (or Wavebox) is positioned on the opposite side of
the aquarium, the inverse operation must be activated on the controller. To do
this, press the “food timer” button on the MASTER Controller for more than 5
seconds. Visually, the function will be indicated through a blinking of the
“select” LED. To switch back to the parallel operation (factory default
setting), the “food timer” button on the MASTER Controller must be pressed
again for more than 5 seconds, which will cause the LED to be lit constantly.
Note: The inverse function cannot be switched to the “external control”
function or during the “auto adjust” operation.
Night mode / Moonlight
Night mode
The photodiode of the Moonlight for the Turbelle is activated by inserting the
(optional) Moonlight 7097.050 into the controller socket, and by mounting it
in the illuminated area of the lamp. Accordingly, the Turbelle pump will be
switched off when the light is turned off in the pulse mode.
With an additional adjustment on the Turbelle controller for the “pulse 2-10
s” wave simulation, the pump will continue to run with the “pulse power” (4)
performance setting. In the morning, after the light has switched on again,
the selected pulse operation of the pumps will continue in the performance
range between “pulse power” (4) and “main power” (2). If oscillating current
was selected on a Turbelle® controller (auto adjust), the pulse operation will
only run while the light is on.
Permanent attachment of the photodiode at a tested position in the aquarium:
For test purposes, hold the photodiode into the beam area of the aquarium lamp
until the Turbelle pump starts the pulse operation. With HQI spotlights a
minimum distance of 30 cm (11.8 in.) must be observed, since light and heat
damages will be unavoidable otherwise
Night mode / Moonlight
Moonlight / moon phase simulation
The moon phase depends on the constellation between the Sun and the Moon.
New Moon consolations occur every 29.53 days on average. The Moonlight with
photodiode 7097.050 (1) offers a simplified moon phase of 29 days. For this, a
special LED is located in the photodiode which is positioned above the water
surface. The moon phase is programmed to reproduce the lunar cycle from the
full moon to the new moon. This cycle can be aligned to the natural moon phase
by inserting the Moonlight with photodiode 7097.050 (1) on a full moon, which
will then reset the phase. The Moonlight is only illuminated when the
photodiode receives very little or no light. It is therefore adapted to the
light cycle of the aquarium.
Detaching the pump cable
For installation purposes, the pump cable can be detached from the controller:
Remove the setting buttons with a small flat-head screwdriver (1).
Remove both screws on the rear side of the housing (2).
Remove the plug from the circuit board, and reattach it after the successful
installation (3).
Cable guard 6040.019
All Turbelle® electronic pumps (6105, 6255) are supplied and preassembled with
a protective tube for cables (1).
synchronous motor pumps, the Cable guard 6040.019 (2) (a helical coil) can be
ordered separately as an accessory. For non-controllable Turbelle® Both
protective tube for cables (for 6105 and 6255) and Cable guard 6040.019 (2)
(non-provided accessory for 6065, 6085 and 6125) protect the cable of all
Turbelle pumps against damage from aquarium inhabitants, such as some coral-
eating fish (e.g. triggerfish) or sea urchins, which eat algae growing on the
cable surface. Therefore, we recommend placing the cable as far as possible in
such a way that it is exposed to as little light as possible to avoid algae
growth.
Cable protection both by the protective tube for cables (1) and by Cable guard
6040.019 (2) is limited in time, since by gnawing off algae, collaterally
small particles of the plastic surface will be removed. For that reason, the
cable guard should be checked regularly and it should even be replaced if the
cable protection can no longer be assured by it.
Caution! If the protective tube for cables or the Cable guard is not in use to
protect a Turbelle pump or not replaced in time with the result of cable
damage by animals, this will lead to a warranty exclusion!
Arrangement examples in aquariums
This type of circulation pump for aquariums from 250 to 4,000 liters (66 to
1,057 USgal.) can be easily concealed in the corners of an aquarium, and
therefore facilitate the harmonious overall appearance of an aquarium with
very strong movement of the water at the same time.
Nano aquariums larger than 250L (66 USgal.) (1) Two Turbelle® stream can be
easily positioned 20 or 30 cm (9 or 12 in.) below the water surface in the
corners of the aquarium, oriented precisely towards the front pane and
surface. Therefore they completely disappear from the aquarium scenery. Using
a timer or SmartController 7000.001, the occuring circulation stream ensures
parallel stream lines.
Aquariums larger than 1,000L (1,057 USgal.) Here, two or four Turbelle stream
can be used for a high/ low tide simulation. With the non-electronical
Turbelle® this can be performed in a 6-hour cycle using a timer, and with a
SmartController 7000.001 for the Turbelle® electronic 6105 eco and 6255 eco.
Servicing
Thoroughly clean the pump and the drive assembly in regular intervals, at
least once a year. In case of unfavourable conditions, such as high lime
content, a lot of sediment or failures, shorter intervals may be necessary
(about every three months).
Open the pump as shown in illustration (1) and pull out the drive assembly
(2).
Clean all parts, which includes the impeller housing, the drive assembly with
impeller as well as the rotor compartment.
Never use hard objects to remove the dirt, but rather a brush or soft cloth
with detergent and/or vinegar. If the drive assembly is too loose and has too
much clearance, replace the entire part.
The assembly is carried out in reverse sequence.
Illustration of parts
The illustration shows the individual parts supplied. The list of spare parts may also contain parts which deviate.
Warranty
The unit manufactured by TUNZE Aquarientechnik GmbH carries a limited
guarantee for a period osixty (60) months after the date of purchase covering
all defects in material and workmanship. Within theframework of the
corresponding laws, your remedies in
case of a violation of the guarantee obligation shall be limited to returning
the unit manufactured by TUNZE® Aquarientechnik GmbH for repair or replacement
at the discretion of the manufacturer. Within the framework of the
corresponding laws, the said shall be the only remedies. Consequential damage
and/or other damage shall be excluded therefrom explicitly. Defect units
shalhave to be shipped to the dealer or the manufacturer in the original
packaging together with the sales slip in a pre-paid consignment. Unpaid
consignments will not be accepted by the manufacturer.
Wear parts such as pump drives or bearing washers include a limited warranty
period of two years. Exclusion from guarantee shall exist also in case of
damage caused by inexpert handling (such as water damage),
technicamodification carried out by the buyer or by connection todevices which
have not been recommended.
Subject to technical modifications, especially those which further safety and
technical progress.
Customers in USA, please refer to seperate Limited Warranty for United States
brochure.
To obtain service under this limited warranty, purchaser must first contact
TUNZE® United States distributor, TUNZE USA, LC via:
email: tunze@sbcglobal.net,
telephone: 512-833-7546 or
U.S. Mail: 2121 Cole Springs Rd, Buda TX 78610, USA to arrange for return of
the product, shipment of a replacement part, or to receive further
instructions. TUNZE or its distributor may require proof of the purchase and
date of purchase by the sales receipt or comparable proof of sale showing the
original date of purchase, the serial number of the product and the seller‘s
name and address. If TUNZE® determines that any product is not covered by this
limited warranty, the purchaser must pay all parts, shipping, and labor
charges for the repair or return of such a product.
This limited warranty is conditioned upon proper use of the product by the
purchaser. This limited warranty does not cover:
(a) defects or damage resulting from accident, misuse, abnormal use, abnormal
conditions, improper storage, sand or dirt, neglect, or unusual physical,
electrical or electromechanical stress;
(b) scratches, dents and cosmetic damage, unless caused by TUNZE ;®
(c) defects or damage resulting from excessive force or use of a metallic
object when conducting maintenance;
(d) ordinary wear and tear;
(e) defects or damage resulting from the use of the product in conjunction or
connection with accessories, products, or ancillary / peripheral equipment not
furnished or approved by TUNZE ® ;
LIMITED WARRANTYAPPLICABLE TO SALES OF TUNZE® PRODUCTS IN THE UNITED STATES OF
AMERICA
Disposal
**** (in keeping with RL2002/96/EU)
The device and the battery may not be disposed of in normal domestic waste; it
has to be disposed of in an expert manner.
Important for Europe: Devices can be disposed of through your community’s
disposal area.
TUNZE® Aquarientechnik GmbH
Seeshaupter Straße 68
82377 Penzberg – Germany
Tel: +49 8856 2022
Fax: +49 8856 2021
info@tunze.com
www.tunze.com
Documents / Resources
|
Tunze 7000.001 Smart
Controller
[pdf] Instruction Manual
7000.001 Smart Controller, 7000.001, Smart Controller, Controller
---|---
|
TUNZE 7000.001 Smart
Controller
[pdf] Instructions
7000.001 Smart Controller, 7000.001, Smart Controller, Controller
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>