SIGOR 9057001 DALI Controller DC/DC 4x8A Instructions
- June 9, 2024
- SIGOR
Table of Contents
SIGOR 9057001 DALI Controller DC/DC 4x8A
Important: Read All Instructions Prior to Installation
Function introduction
Product Data
No.| Input Voltage| Output Current| Output Power| Remarks| Size(LxWxH)| DALI
Consumption
| Dimming Range| Ambient Temperature
---|---|---|---|---|---|---|---|---
1| 12-36VDC| 4x5A| 4x(60-180)W| Constant voltage| 170×53.4x28mm| 2mA|
0.1%-100%| -20℃ ~ +50℃
2| 12-36VDC| 4x350mA| 4x(4.2-12.6)W| Constant current| 170×53.4x28mm| 2mA|
0.1%-100%| -20℃ ~ +50℃
3| 12-36VDC| 4x700mA| 4x(8.4-25.2)W| Constant current| 170×53.4x28mm| 2mA|
0.1%-100%| -20℃ ~ +50℃
- In compliance with IEC 62386-101:2014, IEC 62386-102:2014, IEC 62386-207 Ed2.
- Built-in DALI-2 interface, DALI DT6 device
- Match all DALI systems in the market
- Manual /automatic DALI address setting
- DALI address digitally indicates
- Push dimmer/DALI dimmer optional
- Four channels can set addresses from one to four.
- To work with a power repeater to expand output power unlimitedly.
- Waterproof grade: I P20
Safety & Warnings
- DO NOT install with power applied to device.
- DO NOT expose the device to moisture.
Operation
- This product can be operated under DALI Dimmer mode and Push Dimmer mode while connected with DALI master controllers and push switches respectively.
Switching of Two Modes
- DALI and Push DIM functions cannot be used simultaneously, which can be controlled respectively by DALI master controllers and push switches.
- Set DALI Address Manually Via Buttons
- Press and hold down any of the two buttons until the numeric digital display flashes, then release the button. 1.2. Click any of the two buttons once to select a digit, click again to change the digit until the desired DALI address appears. Click first button to set “tens” position and second button to set “units” position. The address can be set from 00~63.
- Then press and hold down any of the 2 buttons until the numeric digital display stops flashing to confirm the setting.
- Note: DALI address can be manually assigned from 00-63-FF, by factory defaults, no DALI address is assigned for the dimmer, and the display shows. Setting the DALI address will reset the dimmer to factory defaults.
Set DALI Address Quantity
- Press and hold down both of the two buttons until numeric digital display flashes, then release the button.
- Click first button to select “1A”, “2A”, “3A” or “4A” which means 1 address, 2 addresses, 3 addresses or 4 addresses.
- Then press and hold down any of the 2 buttons until the numeric digital display stops flashing to confirm the setting.
For example, when we set address to 22:
- When select 1A, all four channels will be the same address 22.
- When select 2A, channel 1 & 3 will be the same address 22, channel 2 & 4 will be the same address 23.
- When select 3A, channel 1, 2, 3 will be address 22, 23, 24 respectively, and channel 4 address is also 24.
- When select 4A, channel 1, 2, 3, 4 will be address 22, 23, 24, 25 respectively.
DALI Address Assigned by DALI Masters
- DALI address can also be assigned by DALI Master controller automatically, please refer to user manuals of compatible DALI Masters for specific operations.
- Note : The digital display will show When the DALI master is assigning addresses.
Push Dimmer Mode
- While connected with a AC push switch, the digital display will show “PD” which means Push Dimmer Mode, operations under Push Dimmer Mode are as follows:
Click the button to switch ON/OFF
- Press and hold down the button to increase or decrease light intensity to desired level and release it, then repeat the operation to adjust light intensity to opposite direction. The dimming range is from 1% to 100%.
- Memory function after power off or power failure enables the device to memorize the status before power off while power on again.
Wiring diagram
- With DALI master
Conformity & Standards
- Radio Frequency Interference according to EN 55015:2013/A1:2015
- Immunity standard according to EN 61547:2009
- Mains current harmonics according to EN 61000-3-2:2014
- Limits for Voltage Fluctuations and Flicker according to EN 61000-3-3:2013
- CE marked
With AC Push Switch
Product Dimension
-
Sigor Licht GmbH
-
Eichenhofer Weg 81 · 42279 Wuppertal
-
Telefon 0 23 39 – 12 61 0 · Telefax 0 23 39 – 12 61 61
Documents / Resources
|
SIGOR 9057001 DALI Controller DC/DC
4x8A
[pdf] Instructions
9057001 DALI Controller DC DC 4x8A, 9057001, DALI Controller DC DC 4x8A,
Controller DC DC 4x8A
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>