Sunco WP_DD Series LED Wall Pack User Manual
- September 12, 2024
- SUNCO
Table of Contents
Sunco WP_DD Series LED Wall Pack
What’s in the Box
LED Wall Pack
Get Your Gear
Before You Start
Safety Information
To reduce the risk o f fire, electric shock, or physical injury:
- Turn off the switch and circuit breaker before installing this LED light fixture.
- This product should be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
- Use safety precautions and abide by related regional and local laws or regulations.
- Proper grounding is required to ensure safety.
- Suitable for use in wet environments.
- Do not use outdoors or mount near gas or electric heaters.
- Equipment should be mounted in locations and at heights where it will not be subject to tampering by unauthorized personnel.
- Check for damage during shipping prior to install. If the product is damaged, do not use it.
- To ensure efficient light, regularly clean the light panel. Do not clean with harsh solvents.
- Not compatible with occupancy sensors.
- Not compatible with third party sensors.
- Not compatible with timing devices.
WARNING:
- Cancer & Reproductive Harm- www.P65Warnings.ca.gov
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference that may cause undesired operation. Please review all instructions carefully prior to installation.
Quickstart Guide
- Step 1: Open fixture and remove cover.
- Step 2: Drill through fixture’s mounting holes as desired.
- Step 3: Connect the corresponding wires
- Step 4: Adjust the constant current, CCT, and wattage to desired levels.
Installation Guide
STEP 1
- Turn off the circuit breaker for the location where the wall pack will be installed. Make sure the area is well lit by sunlight if the dawn to dusk sensor is going to be used.
- Install a compatible junction box (optional, not included).
STEP 2
- Unscrew the top three screws from the lens, allowing you to remove it. The lens may spring forward.
STEP 3
- Drill (b)out the holes you will be using to connect the wall pack to the junction box. If you are not using a junction box, drill out the top two outer holes in the circle.
- Use the bubble level to ensure the up arrow is properly aligned with the ground.
STEP 4
- Before mounting the wall pack, unscrew a cable port. There is one above the junction box and one on either side.
STEP 5
- Thread light wires through cable ports, then connect light wires with supply wires;
- Black to Black (Live) • White to White (Neutral) • Green to Bare Copper (Ground)
- Optional: To using dimming features, connect dimming wires to compatible device.
- Violet (+) to Violet • Pink (-) t o Pink
Note
- Dimming wires do not apply to WD_DD-BR)
STEP 6
- Junction box:
- Secure the wall pack to the junction box.
- Non junction box:
- Secure the wall pack to the wall. We recommend using conduit for wall packs to protect the cables with a water resistant seal.
STEP 7
- Adjust wattage and color temperature to your liking (options vary by model). You may want to restore power for this step, but be careful of the bright LEDs.
- Reattach the lens by hooking it under the metal loops and then installing the screws.
Product Details
Recommended Dimmers
Brand | Model |
---|---|
LUTRON | NTSTV-DV |
LUTRON | NFTV-IV |
LUTRON | DVTV |
LEVITON | IP710 |
LEVITON | DS710-10Z |
LEGRAND | RH4FBL3PW |
WP_DD_60SW-BR-3050K Specifications
Voltage | 120V-277V | Average Lifetime | 50000 Hours |
---|---|---|---|
CCT | 3000K/4000K/ 5000K | Lumens | 8600LM |
Frequency | 50/60 Hz | Moisture Rating | IP65 |
Beam Angle | 85° | CRI | 80+ |
Weight | 3.7 lbs | Usage | Outdoor |
Housing Material | Aluminium Alloy | Power Factor | >90 |
Dimmable | 0-10V | Warranty | 7 Years |
*Not all options are applicable to all models.
Scan for the full compatible dimmer list!
WP_DD_80W-BR Specifications
Voltage | 120V-277V | Average Lifetime | 50000 Hours |
---|---|---|---|
CCT | 5000K | Moisture Rating | IP65 |
Beam Angle | 100° | Lumens | 11500 LM |
Frequency | 60 Hz | CRI | 80+ |
Weight | 4.84 lbs | Usage | Outdoor |
Housing Material | Aluminium Alloy | Power Factor | >90 |
Dimmable | 0-10V | Warranty | 7 Years |
WP_DD_120SW-BR-3050K Specifications
Voltage | 120V-277V | Average Lifetime | 50000 Hours |
---|---|---|---|
CCT | 3000K/4000K/ 5000K | Lumens | 17000LM |
Frequency | 50/60 Hz | Moisture Rating | IP65 |
Beam Angle | 100° | CRI | 80+ |
Weight | 5.06 lbs | Usage | Outdoor |
Housing Material | Aluminium Alloy | Power Factor | >90 |
Dimmable | 0-10V | Warranty | 7 Years |
*Not all options are applicable to all models.
WP_BR-3050K Specifications
Voltage | 120V-277V | Average Lifetime | 50000 Hours |
---|---|---|---|
CCT | 3000K/4000K/ 5000K | Lumens | Up to 8200LM |
Frequency | 50/60 Hz | Moisture Rating | IP65 |
Beam Angle | 100*87° | CRI | 80+ |
Weight | 3.5 lbs | Usage | Outdoor |
Housing Material | Aluminium Alloy | Power Factor | >90 |
Dimmable | 0-10V | Warranty | 7 Years |
*Not all options are applicable to all models.
WP_DD-BR Specifications
Voltage | 120V-277V | Average Lifetime | 50000 Hours |
---|---|---|---|
CCT | 5000K | Beam Angle | 90*102 |
Country of Origin | Vietnam | Moisture Rating | IP65 |
Frequency | 50/60 Hz | CRI | 80+ |
Weight | 5.06 lbs | Usage | Outdoor |
Housing Material | Aluminium Alloy | Power Factor | >90 |
Dimmable | 0-10V | Warranty | 7 Years |
Scan for full Dusk to Dawn instructions!
Common Troubleshooting
- Feeling in the dark about an issue with your product? No worries! Our troubleshooting section is here to shed some light and provide you with easy-to-follow solutions for any problem.
- If you still need some assistance, please feel free to contact us with any questions. Our team of lighting experts are happy to help brighten your day.
Light Distribution Angle
INTENSITY DISTRIBUTION DIAGRAM IN C PLANS
Not a lighting nerd?
No worries, you can skip this page
AVERAGE BEAM ANGLE (50%): 10 2.9 DEG
- UNIT: cd Luminous Intensity Distribution 1
Lighting distribution angle refers to the spread of light emitted from a light source. It is an important factor to consider when selecting a fixture or bulb, as it affects the way it will illuminate an area. There are two main types of lighting distribution angles:
A symmetric lighting distribution emits light evenly in all directions, creating a cone-shaped pattern that provides a pool of light. This type of lighting is ideal for general lighting and illuminating large areas. Common applications for symmetric lighting include general area illumination, security lighting, and perimeter lighting. Symmetric lighting is also used to a certain degree in up-lighting.
An asymmetric lighting distribution angle, also known as beam angle, creates a pattern that focuses light in a specific direction. This type of lighting is ideal for task lighting as it reduces glare and light spill in other areas. Common applications include task lighting in spaces such as landscape settings, retail stores, museums, and much more.
It is important to note that the lighting distribution angle can also be affected by other factors such as the reflector design of the light source, the type of lens used, and the distance between the light source and the surface being illuminated.
FAQ
- Q: What dimmers are compatible with these LED Wall Packs?
- A: The recommended dimmers are LUTRON NTSTV-DV, NFTV-IV, DVTV, LEVITON IP710, DS710-10Z, and LEGRAND RH4FBL3PW.
CONTACT
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>