UBIQUITI UAP-AC-LR UAP AC LR Access Point User Guide
- June 4, 2024
- UBIQUITI
Table of Contents
UBIQUITI UAP-AC-LR UAP AC LR Access Point
introduction
Included only in the single-pack of the UAP-AC-LR.
Installation Requirements
- CATS/6 cable
- Phillips screwdriver
- Drill and drill bit (6 mm for wal-mounting or 3 mm for ceiling-mounting9)
- Linux, Mac OS X, or Microsoft Windows 7/8/10
- Java Runtime Environment 1.6 (1.8 or newer recommended)
- Web Browser: Google Chrome (Other browsers may have li mited functionality.)
- UniFi Controller software v4.7 or higher (available at: ui.com/download/unifi)
Hardware Overview
-
This Gigabit Ethernet port is used to connect the power and should be connected to the LAN and DHCP server. Power can be provided by a UniFi Switch with PoE or Gigabit
-
PoE adapter (included with single-pack only).
-
Reset
The Reset button serves two functions for the UniFi AP:
Restart Press and release the Reset button quickly.
Restore to Factory Default Settings Press and hold the Reset button for more than five seconds. -
Cable Feed Plug
If your Ethernet cable feeds along the mounting surface, remove the Cable Feed Plug.
Mounting Bracket -
Locking Tab
During installation, the Locking Tab on the Mounting Bracket moves from the Initial
Note : If you need to remove the UniFi AP from the Mounting Bracket, insert a paper clip in the Slot to release the Locking Tab and turn the UniFi AP counterclockwise.
Hardware Installation
The device can be mounted on the wall or ceiling. Perform the steps for the appropriate installation.
Wall Mount
Ceiling Mount
Powering the UniFi AP
Use a UniFi Switch with PoE or a Gigabit PoE adapter for power.
Connecting to a UniFi Switch with PoE
Connect the Ethernet cable from the UniFi AP directly to a PoE port on the
UniFi Switch with PoE.
Connecting to the PoE Adapter
- Connect the Ethernet cable from the device to the POE port of the PoE adapter.
- Connect an Ethernet cable from your LAN to the LAN port of the PoE adapter.
- Connect the Power Cord to the adapter, and then plug the Power Cord into a power outlet.
-
Mounting the PoE Adapter (Optional)
Remove the PoE Mounting Bracket from the adapter, place the bracket at the desired -
location, and mark the two holes.
Pre-drill the holes if necessary, and secure the bracket using two fasteners (not included). -
Align the adapter’s slots with the tabs of the PoE Mounting Bracket, and then slide the adapter down.
Software Installation
Download and install the latest version of the UniFi Controller software.
Launch it and follow the on-screen instructions. The software and step-by-step
instructions in the User
Guide are available at: ui.com/download/unifi After you have installed the
software and run the UniFi Installation Wizard, a login screen will appear for
the UniFi Controller management interface. Enter the username and password
that you created and click Sign In.
You can manage your wireless network and view network statisticS using the
UniFi Controller management interface. For information on configuring and
using the UniFi
Controller software, refer to the User Guide.
Mobile App Installation
Ubiquiti also offers the UniFi app, which is available from the App Store°
(iOS) or Google Play Store (Android). You can use it to provision a UniFi AP
for basic functionality without confguring a UniFi Controller. It also allows
seamless provisioning of APs for remote
Safety Notices
- Read, follow, and keep these instructions.
- Heed all warnings.
- Only use attachments/accessories specified by the manufacturer
WARNING: Do not use this product in location that can be submerged by water.
WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.
Electrical Safety Information
- Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified may result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed.
- There are no operator serviceable parts inside this equipment. Service should be provided only by a qualiied service technician.
- This equipment is provided with a detachable power cord which has an integral safety ground wire intended for connection to a grounded safety outlet.
- Do not substitute the power cord with one that is not the provided approved type. Never use an adapter plug to connect to a 2-wire outlet as this will defeat the continuity of the grounding wire.
- The equipment requires the use of the ground wire as a part of the safety certifñcation, modincation or misuse can provIde a shock hazard that can result in serious injury or death.
- Contacta qualified electrician or the manufacturer if there are questions about the installation prior to connecting the equipment.
- Protective earthing is provided by Listed AC adapter. Building installation shall provide appropriate short-circuit backup protection.
- Protective bonding must be installed in accordance with local national wiring rules and regulations.
Compliance FCC
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions.
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, Uses, and can radiate radio frequency energy and, it not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operations of this equipment ina residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This radio transmitter has been approved by FCC.
ISED Canada
CAN ICES-3(A)/NMB-3(A)
This device complies with ISED Canada licence-exempt RSS standard(s).
Operation is subject to the
following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
This radio transmitter has been approved by ISED Canada. The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.
Radiation Exposure Statement
This equipment complies with radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20 cm between the radiator and your body. This transmitter
must not be co-located or operating in conjunction with any other antenna or
transmitter.
- Note: This device is restricted to indoor use only when operating in the 5150-5350 MHz frequency range within all member states.
- Note: Operation in the 5.8 GHz frequency band is prohibited in BFWA member states. Other countries listed may use the 5.8 GHz frequency band.
WEEE Compliance Statement
Declaration of Conformity
Online Resources
Documents / Resources
|
UBIQUITI UAP-AC-LR UAP AC LR Access
Point
[pdf] User Guide
UAP-AC-LR, UAP AC LR Access Point, UAP-AC-LR UAP AC LR Access Point
---|---
References
- Ubiquiti - Rethinking IT
- Ubiquiti - Downloads
- Ubiquiti - Warranty
- community.ubnt.com/
- WEEE Compliance Statement
- UAP-AC-LR Quick Start Guide
- Ubiquiti Account
- Software Downloads - Ubiquiti
- UniFi - Rethinking IT - Ubiquiti
- Ubiquiti - Warranty
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>