Kenmore W10026670A Washer User Guide

Washer
Use & Care Guide

W10026670A
Sears Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
Sears Canada Inc., Toronto, Ontario, Canada M5B 2B8
www.sears.com
www.sears.ca 

W10026670A Washer

Product Record

For service or warranty assistance, you will need the following information. Have this information available to you when you contact Sears concerning your appliance.
To contact Sears, please refer to the Warranty and the back page of this manual.
In the space following, record your complete model number, serial number, and purchase date. You can find this information on the model and serial number label, located under the washer lid.

Model number 110. _
Serial number ___
Purchase date___
Inlet Hose replacement date__
Inlet Hose replacement date__
Inlet Hose replacement date__
Replace inlet hoses after 5 years of use to reduce the risk of hose failure.
Save these instructions and your sales receipt for future reference.

WASHER SAFETY

Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
DANGER You can be killed or seriously injured if you don’t immediately follow instructions.
WARNING You can be killed or seriously injured if you don’t follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions, including the following:

• Read all instructions before using the washer.
• Do not wash articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, other flammable, or explosive substances as they give off vapors that could ignite or explode.
• Do not add gasoline, dry-cleaning solvents, or other flammable, or explosive substances to the wash water. These substances give off vapors that could ignite or explode.
• Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using the washing machine, turn on all hot water faucets and let the water flow from each for several minutes.  This will release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this time.
• Do not allow children to play on or in the washer. Close supervision of children is necessary when the washer is used near children.
• Before the washer is removed from service or discarded, remove the door or lid.
• Do not reach into the washer if the drum, tub or agitator is moving.
• Do not install or store the washer where it will be exposed to the weather.
• Do not tamper with controls.
• Do not repair or replace any part of the washer or attempt any servicing unless specifically recommended in this manual or in published user-repair instructions that you understand and have the skills to carry out.
• See “Electrical Requirements” for grounding instructions.

SAVE THESE INSTRUCTIONS

WASHER USE

Starting Your Washer

WARNING
Fire Hazard
Never place items in the washer that are dampened with gasoline or other flammable fluids.
No washer can completely remove oil.
Do not dry anything that has ever had any type of oil on it (including cooking oils).
Doing so can result in death, explosion, or fire.
WARNING
**** Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock.

1. Measure detergent and pour it into the washer. If desired, add powdered or liquid color safe bleach.

2. Drop a sorted load of clothes loosely into your washer.
   ■ Load evenly to maintain washer balance. Mix large and small items. Items should move easily through the wash water.
   ■ Load only to the top of the basket as shown. Overloading can cause poor cleaning.

3. (Optional Step) Add liquid chlorine bleach.
   NOTE: Follow the garment and the chlorine bleach manufacturers’ directions for proper use. Undiluted bleach will damage any fabric it touches. The damage appears as rips, holes, tears, or color loss and may not show up until several washings later. To avoid spilling, use a cup with a pouring spout. Do not let bleach splash, drip, or run down into the washer basket. Always measure liquid chlorine bleach. Do not guess. Do not use more than the manufacturer’s recommended amount for a full load. Use less with a smaller load size.
   Style 1: With liquid chlorine bleach dispenser (on some models)
   ■ Use only liquid chlorine bleach in this dispenser. Do not use this dispenser to add powdered chlorine or color-safe bleach to your wash load. Pour measured liquid chlorine bleach into the liquid chlorine bleach dispenser. Bleach is immediately fed into washer and is diluted automatically during the wash part of the cycle.
   Style 2: Without liquid chlorine bleach dispenser (on some models)
   ■ Let the washer fill and begin agitating the load.
   ■ Add bleach 5 minutes into the wash cycle for best cleaning and so that bleach can be removed in the rinse cycle. Pour bleach around the agitator, not directly onto the load to avoid damaging clothing or other items in the load.

4. (Optional Step) Add liquid fabric softener.
   NOTE: Do not spill or drip any fabric softener onto the clothes. Undiluted fabric softener can stain fabrics. Always dilute fabric softener with warm water. Too much fabr ic softener can make some items (diapers and towels) nonabsorbent. If this happens, do not use it on every load, or use less of it in each load.
   Style 1: With liquid fabric softener dispenser (on some models)
   ■ Use only liquid fabric softener in this dispenser. Pour measured liquid fabric softener into the dispenser. Softener is added automatically during the rinse portion of the cycle. Dilute liquid fabric softener by filling the dispenser with warm water until liquid reaches the lowest edge in the dispenser opening.
   NOTE: If your unit has a Fabric Softener Switch (on some models), make sure to turn on this selection when using fabric softener.
   Style 2: Without liquid fabric softener dispenser (on some models)
   In the final rinse only, add fabric softener that has been diluted with  ½ to 1cup (125 to 250 mL) warm water.

5. Close the washer lid.

6. Turn the WATER LEVEL selector to the correct setting for your wash load size and the type of fabric being washed. You may change the water level selection after the washer has started filling by turning the selector to a different setting.
   NOTE: Your washer may be equipped with an Auto Load sensing water level feature that will automatically sense the size of the load and add enough water to efficiently clean the load. To insure the washer calculates the proper amount of water for the load size, do not open the lid or stop the washer once the cycle has started.
   

7. Set the TEMPERATURE selector to the correct setting for the type of fabric and soils being washed. Use the warmest wash water safe for fabric. Follow garment label instructions.
   NOTE: Your washer may be equipped with an Energy Saver Warm or a Cool temperature setting. Using these options will help save energy and also ensure the detergent will dissolve properly.Water Temp| Use for
   ---|---
   Hot| Whites and pastels Heavy soils
   Warm| Bright colors Moderate to light soils
   Cold| Colors that bleed or fade Light soils

NOTES:
■ Your washer may be equipped with Automatic Temperature Control (ATC). ATC electronically senses and maintains the temperature in the washtub by alternating between incoming hot and cold water.
■ In wash water temperatures colder than 60°F (15.6°C), detergents do not dissolve well. Soils can be difficult to remove. Some fabrics can retain wear wrinkles and have
increased pilling (the formation of small lint-like balls on the surface of garments).

8. (Optional Step) OPTIONS selector (on some models). For an additional rinse and spin at the end of a wash cycle, set the Options selector to 2nd Rinse. On some models, the 2nd Rinse feature is part of the cycle.
9. (Optional Step) SOIL LEVEL selector (on some models). Each soil level setting is designed for different types of fabric and soil levels.
10. Push in the Cycle Control knob and turn it clockwise to the wash cycle you want. Reduce the wash time when using a small water level setting. Pull out the Cycle Control knob to start the washer.
    To stop or restart your washer:
    ■  To stop the washer at any time, push in the Cycle Control knob.
    ■  To restart the washer, close the lid (if open) and pull out the Cycle Control knob.

WASHER CARE

Cleaning Your Washer
Use a soft, damp cloth or sponge to wipe up any spills such as detergent or bleach from the outside of your washer.
Clean your washer interior by mixing 1 cup (250 mL) of chlorine bleach and enough detergent to equal twice the manufacturer’s into your washer and run it through a  complete cycle using hot water. Repeat this process if necessary. recommended amount for a normal wash load. Pour this mixture Remove any hard water deposits using only cleaners labeled as washer safe.
NOTE: If your washer has the Auto Load Sensing feature, use the Bulky cycle.
Cleaning the liquid fabric softener dispenser (on some models):
Style 1: To remove dispenser, grasp the top of the dispenser with both hands. Squeeze and push upward with both thumbs to remove. Flush the dispenser with warm water.

Style 2:

1. Hold the top agitator section with one hand. Using the other hand, rotate the dispenser clockwise until it stops (approximately 1″ [2.54 cm]). To remove, lift the  dispenser straight up. Using a rocking motion, separate the top and base of the dispenser. Wash three parts (the base, the cone-shaped cup, and the top) with a mild detergent and warm water.

2. Making sure the pointed end of the cone-shaped cup is pointed toward the base, assemble the three parts by pressing the top and bottom sections together. For ease of
   assembly, reassemble the dispenser with the parts upside down. If the seal came off while removing the dispenser from the agitator, install the seal as shown below.
   A. Top
   B. Cone-shaped cup
   C. Base
   D. Seal

3. Reinstall the dispenser by aligning the two locking tabs on the base of the dispenser with the two small slots on the top of the agitator. Push the dispenser down until you hear it snap into place. If you cannot get the locking tabs to snap into place, check the seal. It must be positioned as shown in Step 2.
   A. Dispenser assembly
   B. Locking tab on dispenser base
   C. Small slots on agitator
   D. Agitator assembly

IMPORTANT: Some models are equipped with a liquid fabric softener dispenser. To avoid damage to the washer or clothing, do not wash clothes with the liquid fabric softener dispenser removed or add detergent or bleach to this dispenser; it is for liquid fabric softener only.

Water Inlet Hoses
Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Periodically inspect and replace inlet hoses if bulges, kinks, cuts, wear, or leaks are found.
When replacing your inlet hoses, mark the date of replacement on the hose with a permanent marker or in the product record section of this book.
Moving and Storage
Because some water may stay in the hoses, freezing can damage your washer. If storing or moving your washer during freezing weather, winterize it.

Winterizing your washer

1. Shut off both water faucets. Disconnect and drain water inlet hoses. Pour 1 qt (1 L) of R.V.-type antifreeze into the basket.
2. Run washer on a drain and spin setting for about 30 seconds to mix the antifreeze and remaining water.
3. Unplug washer or disconnect power.

To use washer again

1.  Flush water pipes and hoses. Reconnect water inlet hoses.
   Turn on both water faucets.
   WARNING
   Electrical Shock Hazard
   Plug into a grounded 3 prong outlet.
   Do not remove ground prong.
   Do not use an adapter.
   Do not use an extension cord.
   Failure to follow these instructions can result in death, fire, or electrical shock.

2. Plug in washer or reconnect power.

3. Run the washer through a complete cycle with 1 cup (250 mL) of detergent to clean out antifreeze.

Storage, non-use, or vacation care
Operate your washer only when you are at home. If you will be on vacation or not using your washer for an extended period of time, you should:

1. Unplug washer or disconnect power.
2. Turn off the water supply to the washer. This helps avoid flooding (due to a water pressure surge) while you are away.

STAIN REMOVAL GUIDE

| Antiperspirants, Deodorants
Apply a prewash soil and stain remover. Let stand for 5 to 10 minutes. Wash in hottest water safe for fabric.
---|---
| Blood
Rinse immediately or soak in cold water with detergent for 30 minutes. Rinse. Rub detergent into any remaining stains. Rinse thoroughly. Wash.
| Cream, Milk, Ice Cream
Sponge immediately or apply a prewash soil and stain remover. Rinse. Wash. Repeat if necessary. If stain remains, apply a few drops of liquid detergent. Rinse. If stain remains, soak. Wash.
| Grape, Wine
Soak immediately in cool water. Wash. If stain remains, cover area with a paste made of colorsafe bleach and a few drops of hot water. Wait  15 to 20 minutes. Wash.
| Grass
Use an enzyme presoak or rub enzyme detergent on the stain. Launder with detergent and bleach appropriate for the fabric.
| Ketchup, Tomato Products
Sponge immediately or apply a prewash soil and stain remover. Rinse. Wash. If stain remains, apply a liquid detergent to stain or soak in warm water with detergent. Rewash.
| Mud
Brush off the dry mud. Rinse under cold water.
Pretreat with a paste of detergent and water.
Launder using detergent and bleach safe for the fabric.
| Ring around the Collar
Pretreat with heavy liquid laundry detergent or soak garment in warm water with a granular laundry detergent.
| Chocolate/Coffee
Rinse immediately in cold water. Soak or prewash in warm water using a detergent containing enzymes. Wash. Difficult stains may require using a bleach safe for the fabric.
| Cosmetics
Dampen stain and rub with bar soap. Rinse.
Pretreat with laundry detergent (liquid or a paste of granular detergent and water). Wash.
| Dirty Motor Oil
Pretreat with a liquid laundry detergent or a paste of granular detergent and water. Wash.

■ Do not tumble dry soiled or stained items. Heat may permanently set stains.

TROUBLESHOOTING

First try the solutions suggested here and possibly avoid the cost of a service call…

Washer and Components
Noisy, vibrating, off-balance

• Did you completely remove the yellow shipping strap with cotter pins from the rear of the washer? See “Installation Instructions.”
• Is the floor flexing, sagging, or not level? Flooring that flexes or is uneven can contribute to noise and vibration of the washer. A 3⁄4″ (1.9 cm) piece of plywood under the washer will reduce the sounds. See “Installation Instructions.”
• Is the washer level? The washer must be level. See “Installation Instructions.”
• Are the front feet installed? The front feet should be properly installed and the nuts tightened. Reset the rear leveling legs. All four feet must be firmly in contact with the floor. See “Installation Instructions.”
• Is the load balanced? Evenly distribute the load in the washer basket and make sure the height of the load does not exceed the top row of basket holes.
• Are the gears engaging after the drain and before spin, or is the upper part of agitator clicking during wash? These are normal washer noises.
• Is the washer gurgling or humming? When the washer drains, the pump will make a continuous humming with periodic gurgling or surging sounds as the final amounts of water are removed. This is normal.
• The washer basket moves while washing. This is normal.

Leaking

• Are the fill hoses tight?
• Are the fill hose gaskets properly seated? Check both ends of each hose. See “Connect the Inlet Hoses” in the Installation Instructions.
• Is the drain hose properly installed? The drain hose should be secured to the drainpipe or laundry tub. See “Secure the Drain Hose” in the Installation Instructions.
• Is the sink or drain clogged? Sink and drainpipe must be able to carry away 17 gal. (64 L) of water per minute. If sink or drainpipe is clogged or slow, water can back up out of drainpipe or sink. Check household plumbing (laundry tubs, faucets, drainpipe, water pipes) for leaks.
• Is water splashing off the tub ring? Center the tub before starting the washer.
• Is water splashing off the load? Evenly distribute the load in the washer basket and make sure the height of the load does not exceed the top row of basket holes. The fill or spray rinses can splash off the load.
• Is the washer properly installed? The washer must be level. The front feet should be properly installed and the nuts tightened. Reset the rear leveling legs. See “Level the
  Washer” in the Installation Instructions.

Dispenser operation

• Did you follow the manufacturer’s directions when adding detergent and fabric softener to the dispensers (on some models)? Measure detergent and fabric softener. Slowly pour into the dispensers. Wipe up all spills. Dilute fabric softener in the fabric softener dispenser.
• Did you put powdered or liquid color-safe bleach into the liquid chlorine bleach dispenser (on some models)? Add powdered or liquid color-safe bleach directly to the washer basket. Do not use the chlorine bleach dispenser for colorsafe bleach.
• Is the fabric softener dispenser clogged? Clean the fabric softener dispenser. See “Washer Care” for details.
• Did you use the Fabric Softener option (on some models)?
  When using fabric softener, make sure to turn the Fabric Softener knob to the Softener Added position.

Washer Operation
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock.

Washer won’t run, fill, rinse, or agitate; washer stops

• Is the power cord plugged into a grounded 3 prong outlet? Plug power cord into a grounded 3 prong outlet.

• Are you using an extension cord? Do not use an extension cord.

• Is the indicator on the Cycle Control knob properly lined up with a cycle? Turn the Cycle Control knob to the right slightly and pull to start.

• Are the water inlet valve screens clogged? Turn off the water and remove inlet hoses from the washer. Remove any accumulated film or particles. Reinstall hoses, turn on water, and check for leaks.

• Are both the hot and cold water faucets turned on?
  Turn on the water.

• Is the water inlet hose kinked? Straighten the hoses.

• Does the water level seem too low, or does the washer appear to not fill completely? The top of the agitator is much higher than the highest water level. This is normal annecessary for clothes to move freely.

• Has a fuse blown, or has a circuit breaker tripped?
  Replace the fuse, or reset the circuit breaker. If the problemcontinues, call an electrician.

• Is the washer in a normal pause in the cycle? The washpauses for about 2 minutes during certain cycles. Allow thcycle to continue. Some cycles feature periods of agitationand soak.

• Is the washer overloaded? Wash smaller loads.

• Is the lid open? The lid must be closed during operation.
  Washer will not agitate or spin with the lid open. On models with Auto Load Sensing, water fill will not begin with the lid open.

Washer continues to fill or drain, cycle seems stuck

• Is the top of drain hose lower than the control knobs on washer? The top of the drain hose must be at least 39″ (99 cm) above the floor. See “Drain System” in the Installation Instructions.
• Does the drain hose fit too tightly in the standpipe, or is it taped to the standpipe? The drain hose should be loose yet fit securely. Do not seal the drain hose with tape. The hose needs an air gap. See “Secure the Drain Hose” in the Installation Instructions.

Washer won’t drain or spin, water remains in washer

• Is the drain hose clogged, or the end of the drain hose more than 96″ (244 cm) above the floor? See “Drain System” in the Installation Instructions.
• Is the lid open? The lid must be closed during operation. Washer will not agitate or spin with the lid open.
• Is there excessive sudsing? Always measure detergent. Follow manufacturer’s directions. If you have very soft water, you might need to use less detergent.

Wash/Rinse temperature

• Are the hot and cold water inlet hoses reversed? See “Connect the Inlet Hoses” in the Installation Instructions.
• Are you washing many loads? As your frequency of loads washed increases, the water temperature may decrease for hot and warm temperatures. This is normal.
• Did you select a Warm/Warm temperature setting? On models without AUTO TEMPERATURE CONTROL (ATC) that do have a Warm/Warm temperature  selection, the warm wash will be followed by an energy saving cold rinse followed by warm spray rinses. This saves energy while providing the same rinse performance.
• Do you have an ENERGY STAR washer? The wash water temperatures may feel cooler to you than those of your previous washer. This is normal.

Load too wet

• Did you use the right cycle for the load being washed?
  Select a cycle with a higher spin speed (if available).

• Did you wash an extra large load? A large unbalanced load could result in a reduced spin speed and wet clothes at the end of the cycle. Evenly distribute the load and make sure the height of the load does not exceed the top row of basket holes.

Residue or lint on load

• Did you sort properly? Sort lint givers (towels, chenille) from lint takers (corduroy, synthetics). Also sort by color.

• Did you overload the washer? The wash load must be balanced and not overloaded. Clothes should move freely. Lint or powdered detergent can be trapped in the load if
  overloaded. Wash smaller loads.

• Did you select the correct water level? The water level should be correct for the load size. The load should be under water.

• Did you use enough detergent? Follow manufacturer’s directions. Use enough detergent to hold the lint in the water.

• Did you line dry your clothing? If so, you can expect some lint on the clothing. The air movement and tumbling of a dryer removes lint from the load.

• Was paper or tissue left in the pockets?

• Is your water colder than 60°F (15.6°C)? Wash water colder than 60°F (15.6°C) may not completely dissolve the detergent.

• Did you use the proper cycle time and agitation speed for the load? Reducing wash time (duration) and agitation speed are ways to reduce lint.

• Did you select the 2nd Rinse option (on some models)? A second rinse may reduce residue or lint on the load.

Load is wrinkled, twisted, or tangled

• Did you unload the washer promptly? Unload the washer as soon as it stops.
• Did you use the right cycle for the load being washed? Use cycles with shorter wash times and low wash and spin speeds (if available) to reduce wrinkling, tangling, and twisting.
• Did you overload the washer? The wash load must be balanced and not overloaded. Loads should move freely during washing to reduce wrinkling, tangling, and twisting.
• Was the wash water warm enough to relax wrinkles? If safe for the load, use warm or hot wash water. Use cold rinse water.
• Are the hot and cold water hoses reversed? Check to be sure the hot and cold water hoses are connected to the right faucets. A hot rinse followed by spin will cause wrinkling. See “Connect the Inlet Hoses” in the Installation Instructions.
• Did you wrap items around the agitator? Drop items loosely into the washer. Do not wrap items around the agitator.

Stains, gray whites, dingy colors

• Did you properly sort the load? Transfer of dye can occur when mixing whites and colors in a load. Sort dark clothes from whites and lights.

• Was the wash temperature too low? Use hot or warm washes if safe for the load. Make sure your hot water system is adequate to provide a hot water wash.

• Did you use enough detergent, or do you have hard water? Use more detergent for washing heavy soils in cold or hard water.

• Are the hot and cold water hoses reversed? Check that the hot and cold water hoses are connected to the right faucets. See “Connect the Inlet Hoses” in the Installation
  Instructions.

• Did you follow the manufacturer’s directions when adding detergent and fabric softener? Measure detergent and fabric softener. Use enough detergent to remove soil and hold it in suspension. Dilute fabric softener and add to the rinse portion of a cycle only. Do not drip fabric softener onto clothes.

• Is there above average iron (rust) in water? You may need to install an iron filter.

Garments damaged

• Were sharp items removed from pockets before washing? Empty pockets, zip zippers, snap or hook fasteners before washing to avoid snagging and tearing of load.
• Were strings and sashes tied to avoid tangling? Straps and strings can easily become entangled in the load, causing strain on seams and tearing.
• Were items damaged before washing? Mend rips and broken threads in seams before washing.
• Did you overload the washer? The wash load must be balanced and not overloaded. Loads should move freely during washing.
• Did you add chlorine bleach properly? Do not pour chlorine bleach directly onto load. Wipe up bleach spills. Undiluted bleach will damage fabrics. Do not place load items on top of the bleach dispenser when loading and unloading the washer (on some models). Do not use more than than the manufacturer’s recommended amount for a full load.
• Did you follow the manufacturer’s care label instructions?

PROTECTION AGREEMENTS

Master Protection Agreements
Congratulations on making a smart purchase. Your new Kenmore® product is designed and manufactured for years of dependable operation. But like all products, it may  require preventive maintenance or repair from time to time. That’s when having a Master Protection Agreement can save you money and aggravation.
The Master Protection Agreement also helps extend the life of your new product. Here’s what the Agreement* includes:
Parts and labor needed to help keep products operating properly under normal use, not just defects. Our coverage goes well beyond the product warranty. No deductibles, no functional failure excluded from coverage— real protection.
Expert service by a force of more than 10,000 authorized Sears service technicians, which means someone you can trust will be working on your product.
Unlimited service calls and nationwide service, as often as you want us, whenever you want us. “No-lemon” guarantee – replacement of your covered product if four or more product failures occur within twelve months.
Product replacement if your covered product can’t be fixed.
Annual Preventive Maintenance Check at your request – no extra charge.
Fast help by phone – we call it Rapid Resolution – phone support from a Sears representative on all products. Think of us as a “talking owner’s manual.”
Power surge protection against electrical damage due to power fluctuations.
$250 Food Loss Protection annually for any food spoilage that is the result of mechanical failure of any covered refrigerator or freezer.
Rental reimbursement if repair of your covered product takes longer than promised.
10% discount off the regular price of any non-covered repair service and related installed parts.

Once you purchase the Agreement, a simple phone call is all that it takes for you to schedule service. You can call anytime day or night, or schedule a service appointment online.
The Master Protection Agreement is a risk free purchase. If you cancel for any reason during the product warranty period, we will provide a full refund. Or, a prorated refund anytime after the product warranty period expires. Purchase your Master Protection Agreement today!
Some limitations and exclusions apply. For prices and additional information in the U.S.A. call 1-800-827-6655.
*Coverage in Canada varies on some items. For full details call Sears Canada at 1-800-361-6665.

Sears Installation Service
For Sears professional installation of home appliances, garage door openers, water heaters, and other major home items, in the U.S.A. or Canada call 1-800-4-MY-HOME®.

KENMORE APPLIANCE WARRANTY

ONE YEAR LIMITED WARRANTY
When installed, operated and maintained according to all instructions supplied with the product, if this appliance fails due to a defect in material or workmanship within one year from the date of purchase, call 1-800-4-MY-HOME® to arrange for free repair.
If this appliance is used for other than private family purposes, this warranty applies for only 90 days from the date of purchase.

THIS WARRANTY COVERS ONLY DEFECTS IN MATERIAL
AND WORKMANSHIP. SEARS WILL NOT PAY FOR:

1. Expendable items that can wear out from normal use, including but not limited to filters, belts, light bulbs, and bags.
2. A service technician to instruct the user in correct product installation, operation or maintenance.
3. A service technician to clean or maintain this product.
4. Damage to or failure of this product if it is not installed, operated or maintained according to all instructions supplied with the product.
5. Damage to or failure of this product resulting from accident, abuse, misuse or use for other than its intended purpose.
6. Damage to or failure of this product caused by the use of detergents, cleaners, chemicals or utensils other than those recommended in all instructions supplied with the product.
7. Damage to or failure of parts or systems resulting from unauthorized modifications made to this product.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
Customer’s sole and exclusive remedy under this limited warranty shall be product repair as provided herein. Implied warranties, including warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest period allowed by law. Sears shall not be liable for incidental or consequential damages. Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, or limitations on the duration of implied warranties of merchantability or fitness, so these exclusions or limitations may not apply to you.
This warranty applies only while this appliance is used in the United States and Canada.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co.
Hoffman Estates, IL 60179
Sears Canada Inc.
Toronto, Ontario, Canada M5B 2B8

Get it fixed, at your home or ours!
Your Home
For expert troubleshooting and home solutions advice:
manage my home
www.managemyhome.co
For repair – in your home – of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it I
For the replacement parts, accessories and owner’s manuals that you need to do-it-yourself.
For Sears professional installation of home appliances and items like garage door openers and water heaters.
1-800-4-MY-HOME® c1-aoo-469-4663)
Call anytime, day or night (U.S.A. and Canada)
www.sears.com www.sears.ca
OurHome
For repair of carry-in items like vacuums, lawn equipment, and electronics, call anytime for the location of your nearest Sears Parts & Repair Service Center
1-800-488-1222 (U.S.A.) 1-800-469-4663 (Canada)
www.sears.com www.sears.ca

To purchase a protection agreement on a product serviced by Sears:
1-800-827-6655 (U.S.A.)
1-800-361-6665 (Canada)

® Registered Trademark /™ Trademark /SM Service Mark of Sears Brands, LLC, used under licensee by Sears Canada.
W10026670A
© 2008 Sears Brands LLC
Printed in U.S.A.

References

• cargo.si - This website is for sale! - cargo Resources and Information.
• fluids.no is parked
• The domain name normal.la is for sale
• The domain name open.is is for sale
• Fidesta

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>