PETKIT FF-W-0005-002 FF-T1 Wireless Pump Instructions
- June 9, 2024
- PETKIT
Table of Contents
PETKIT FF-W-0005-002 FF-T1 Wireless Pump Instructions
Product Overview
The main structure
This specification describes a miniature wireless pump, which is mainly
composed of brushless DC electric motor and centrifugal pump (as shown in
Figure 1). It has the characteristics of small size, full sealing of
electrical components, wireless power supply, built-in water level sensor to
realize water shortage protection, safe, reliable and super quiet. Mainly
suitable for pet drinking machine.
The working principle of
Through the wireless transmitter to pump motor drive board power supply, when
the water level submerged sensor 1/2 ~ 2/3, the pump began to work, water from
the outlet pump; When the water level is lower than the sensor, the drive
plate stops output and the pump stops working.
Outline drawing
Product marking
Main parameters
| Item | Standard | Test equipment | test frequency |
|---|---|---|---|
| 5.0V | Load current | 120～150(mA) | Ac and DC electrical parameter |
| tester,wireless transmitter | All inspection of production line | ||
| Water shortage stop current | 90～120(mA) | Ac and DC electrical parameter | |
| tester,wireless transmitter | All inspection of production line | ||
| Load power | ≤0.8(W) | Ac and DC electrical parameter tester,wireless | |
| transmitter | All inspection of production line | ||
| Lift | 17～20(cm) | Pump performance test stand, wirelesstransmitter stand |
Sampling inspection
Maximum flow| 1.20～1.40(L/min)| Pump performance test stand,
wirelesstransmitter stand| Sampling inspection
Transmissiondistance(mm)| 6mm| Test Fixture| Samplinginspection
low-voltage start-up| ≤4.4（V）| Pump performance test bench, wireless
transmitter base DC power supply, wireless transmitterbase, water tank| All
inspection of production line
Maximum Excitation Voltage| ≤6V| Pump performance test bench, wireless
transmitter base DC power supply, wireless transmitterbase, water tank|
Sampling inspection
Water level monitoring| Water level monitoring power status, water level is
lower than the sensor, the pump stops working; When the water level submerges
the sensor 1/2 ~ 2/3, the pumpstarts to work.| Pump performance test bench,
wireless transmitter base DC power supply, wireless transmitter base, water
tank| All inspection of production line
Noise| ≤30（dB）| Sound level meter| Samplinginspection
Life Time| ≥20000(Hour)| Endurance tests| Sampling, typetest
Installation Method
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, that may cause undesired operation.
FCC warning:
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>