DELTA DT022202-BL Angled Supply Stop Valve Instruction Manual
- June 9, 2024
- Delta
Table of Contents
DELTA DT022202-BL Angled Supply Stop Valve
Cleaning and Care
Care should be given to the cleaning of this product. Although its finish is extremely durable, it can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel.
Failure to read these instructions prior to installation may result in personal injury, property damage, or product failure. Manufacturer assumes no responsibility for product failure due to improper installation.
TOOLS NEEDED
You may need
Inlet Connections
A
Copper Compression Inlet Connection
Do not use pipe dope, plumber’s tape, or other gasket material on water line connections. For use with ½” copper type L or M tubing only. Turn off water supply before starting. Cut tubing cover length (1) to fit over copper supply tube (2). Leave 3/4″ (20 mm) clearance from end of supply tube to make connections. Slide escutcheon (3) onto end of tubing cover and install over copper supply tube. Place compression nut (4) and sleeve (5) onto the copper supply tube. If necessary, push tubing cover (1) behind finished wall surface to make room for compression nut and sleeve. Make sure all fittings and connections are free of burrs and debris. Insert copper supply tube into supply stop valve and hand tighten compression nut (4) making sure the supply stop is square and fully seated against the copper supply tube. Using wrenches, hold the supply stop and tighten the compression nut (4) 3/4 additional turn. Protect finished surfaces while using wrenches. Do not overtighten. Slide tubing cover (1) against the compression nut (4). While holding tubing cover in place, slide escutcheon (3) against wall. Turn on water and examine for leaks.
B PEX Compression Inlet Connection
Do not use pipe dope, plumber’s tape, or other gasket material on water line
connections. For use with ASTM F876/F877 PEX only. Turn off water supply
before starting.
Cut tubing cover length (1) to fit over PEX supply tube (2). Leave 3/4″ (20
mm) clearance from end of supply tube to make connections. Slide escutcheon
(3) onto end of tubing cover and install over PEX supply tube. Place
compression nut (4) and sleeve (5) onto the PEX supply tube. Insert stainless
steel tube (6) into the PEX supply tube.
If necessary, push tubing cover (1) behind finished wall surface to allow room
for compression nut and sleeve. Make sure all fittings and connections are
free of burrs and debris. Insert PEX supply tube (2) fully into the supply
stop valve and hand tighten compression nut (4) making sure the supply stop is
square and fully seated against the PEX supply tube. Using wrenches, hold the
supply stop and tighten the compression nut (4) one additional turn. Protect
finished surfaces while using wrenches. Slide tubing cover (1) against the
compression nut (4). While holding tubing cover in place, slide escutcheon (3)
against wall. Turn on water and examine for leaks
PEX compression outlet connection
A
Standard Connections
NOTICE
To avoid risk of property damage, Follow instructions for proper installation.
Failure to follow these instructions may result in risk of property damage
caused by leaking at this connection. Do not use pipe dope or other sealants
on water line connections
Ensure all fittings and end connections are free of debris. Faucet fittings
(1) are 3/8″ compression. Loop tubing (2) if it is too long.
Note: Recommended tubing minimum bend diameter is 8″. Secure metal nut
(3) to supply valve connection (4). Turn nut until it feels snug. Then tighten
nut at least 2 more turns with a wrench. Protect finish surfaces when using
the wrench. Repeat for other tube. Turn on water, examine for leaks.
B
Custom Fit Connections
NOTICE
If you determine the PEX supply tubing for this faucet is too long and must
be shorter to create an acceptable installation, be sure to read the
instructions and plan ahead. When cutting the supply tubing the installer
accepts the responsibility to do so in a way that allows a leak-free joint to
be created. Delta is not responsible for tubing that is cut too short or cut
in a way that will not allow for a leak-free joint. DO NOT use a metalsleeve
(ferrule) or gasket (supplied with faucet) in place of the plastic sleeve
(ferrule) supplied, it may not create a leak-free joint. Do not use pipe dope
or other sealants on water line connections.
For custom fit installations, you must use plastic sleeves (ferrules) supplied
with model and nuts included on supply lines. Tube cut must be straight. See
plastic sleeve (ferrule) installation instructions found in and included in
this document for more information.
Insert stainless steel tube (4) into the pex supply tube.Slide nut (1) over
plastic sleeve (ferrule) (3). Start nut by hand onto supply valve connection
(2) to prevent cross-threading. Turn nut until it feels snug. Then tighten nut
at least 2 more turns with a wrench. Protect finish surfaces when using the
wrench. Repeat for other tube. Turn on water, examine for leaks.
Potential Problems and Remedies
- Tubing is not cut perpendicular to the axis of the tube: carefully make an additional cut, being careful not to cut the tube too short.
- Tubing is cut too short: buy a coupling union and a replacement supply line that mate together from a store. The coupling union end intended to connect to the faucet must mate to the standard 3/8″ connection nuts and plastic sleeves (ferrules) supplied with the faucet.
- The plastic sleeve (ferrule) or connection nut is lost: purchase a replacement nut and/or plastic sleeve (ferrule) that are designed to seal with PEX tubing.
Correct method
NOTICE Failure to use plastic sleeve (ferrule) in the correct orientation
will result in disconnection and possible water damage.
- Determine desired length of supply tube (1). Leave 1″ or 2″ of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free.
- Slide nut (2) and plastic sleeve (ferrule) (3) onto cut supply tube. Ensure plastic sleeve (ferrule) is oriented as shown.
- Insert supply tube into supply valve connection (4). Supply tube should touch bottom of hole inside supply valve.
- Slide plastic sleeve (ferrule) down supply tube until it contacts the supply valve connection.
- Slide nut over plastic sleeve (ferrule). Start nut by hand to prevent cross-threading. Turn nut until it feels snug. Then tighten nut at least 2 more turns with a wrench. Repeat for other supply line. Turn on water, examine for leaks.
Incorrect Installation
Do not install sleeve upside down
Ensure cut is straight
Ensure tube is fully inserted into stop before sliding sleeve down to engage top of fitting
Ensure cut is straight.
C
Copper compression outlet connection
Do not use pipe dope, plumber’s tape, or other gasket material on water line
connections. For use with 3/8” copper type L or M tubing only. Turn off water
supply before starting.
Position and cut copper outlet tube (1) to length so that it seats fully into
the supply stop valve. Slide compression nut (2) and sleeve (3) onto the
copper outlet tube.
Insert copper supply tube fully into the supply stop valve and hand tighten
compression nut (2). While making sure the copper supply tube is square and
fully seated into the supply stop, tighten the compression nut (2) with a
wrench 1 to 1-1/4 additional turns. Protect the finished surfaces when using
the wrench.
Do not overtighten. Turn on water and examine for leaks.
LIMITED WARRANTY ON DELTA® ACCESSORY PRODUCTS
Delta® Accessories are warranted to the original consumer purchaser or
commercial purchaser, as applicable, to be free from defects in material and
workmanship for the applicable period specified below:
Parts and Finish of Delta Accessories (excluding Sink Accessories). All parts
and finishes (other than electronic parts and batteries) of Delta Accessories,
other than sink accessories, purchased from authorized Delta sellers are
warranted to the original consumer purchaser to be free from defects in
material and workmanship for as long as the original consumer purchaser owns
the home in which the accessory was first installed. For commercial
purchasers, (a) the warranty period is ten (10) years for multi-family
residential applications and (b) five (5) years for all other commercial
applications, in each case from the date of original purchase.
For purposes of this warranty, the term “multi-family residential application”
refers to the purchase of the accessory from an authorized Delta seller by a
purchaser who owns but does not live in the residential dwelling in which the
accessory is initially installed, such as in a rented or leased single unit or
multi-unit detached home (duplex or townhome), or a condominium, apartment
building or community living center. The following installations are not
considered multi-family residential applications, are excluded from the
10-year warranty and are subject to the five year warranty: industrial,
institutional or other business premises, such as a dormitory, hospitality
premises (hotel, motel or extended stay location), airport, educational
facility, long- or short-term healthcare facility (hospital, rehabilitation
center, nursing, assisted or staged-care living unit), public space or common
area.
Parts and Finish of Delta Sink Accessories. All parts and finishes of Delta
Sink Accessories purchased from authorized Delta sellers are warranted to the
original purchaser to be free from defects in material and workmanship for one
(1) year from the date of purchase. Parts and Finish for Delta Recertified
Accessories. Delta Faucet Company offers for sale on deltafaucet.com Delta
Recertified Accessories. All parts (other than electronic parts and batteries)
and finishes of these Delta Recertified Accessories, (other than Sink
Accessories) are warranted to the original consumer purchaser to be free from
defects in material and workmanship for ten (10) years from the date of
original purchase. For commercial purchasers, the warranty period is one (1)
year from the date of original purchase. Delta Recertified Sink Accessories
are warranted to the original purchaser to be free from defects in material
and workmanship for one (1) year from the date or purchase. Electronic Parts.
Electronic parts (other than batteries), if any, of Delta Accessories
purchased from deltafaucet.com or authorized Delta sellers are warranted to
the original consumer purchaser to be free from defects in material and
workmanship for two (2) years from the date of original purchase or, for
commercial purchasers, for one (1) year from the date of original purchase. No
warranty is provided on batteries.
What We Will Do. Delta Faucet Company will repair or replace, free of charge,
during the applicable warranty period (as described above), any part or finish
that proves defective in material and/or workmanship under normal
installation, use and service. If repair or replacement is not practical,
Delta Faucet Company may elect to refund the purchase price in exchange for
the return of the product. These are your exclusive remedies.
What Is Not Covered. Because Delta Faucet Company is unable to control
the quality of Delta products sold by unauthorized sellers, unless otherwise
prohibited by law, this warranty does not cover Delta products purchased from
unauthorized sellers.
Any labor charges incurred by the purchaser to repair, replace, install or
remove this product are not covered by this warranty. Delta Faucet Company
shall not be liable for any damage to the product resulting from reasonable
wear and tear, outdoor use, misuse (including use of the product for an
unintended application), abuse, neglect or improper or incorrectly performed
installation, maintenance or repair, including failure to follow the
applicable installation, care and cleaning instructions. We also recommend
that you use only genuine Delta ® replacement parts.
What You Must Do To Obtain Warranty Service or Replacement Parts. A warranty claim may be made and replacement parts may be obtained by calling 1 800 355-2721 or by contacting us by mail or online as follows (please include your model number and date of original purchase):
In the United States and Mexico:
Delta Faucet Company
55 E. 111th Street Indianapolis, IN 46280
Attention: Warranty Service
Attention: Warranty Service
www.deltafaucet.com/service-parts/contact-us
In Canada:
Masco Canada Limited, Plumbing Group
Technical Service Centre
350 South Edgeware Road
St. Thomas, Ontario, Canada N5P 4L1
Attention: Customer Service
http://www.deltafaucet.ca/customersupport/assistance.html
Proof of purchase (original sales receipt) from the original purchaser must be
made available to Delta Faucet Company for all warranty claims unless the
purchaser has registered the product with Delta Faucet Company or the product
is a Delta Recertified product purchased from deltafaucet.com. This warranty
applies only to Delta accessories manufactured after January 1, 2019 and
installed in the United States of America, Canada and Mexico. Limitation on
Duration of Implied Warranties. Please note that some states/provinces
(including Quebec) do not allow limitations on how long an implied warranty
lasts, so the below limitations may not apply to you. TO THE MAXIMUM EXTENT
PERMITTED BY APPLICABLE LAW, ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE, IS
LIMITED TO THE STATUTORY PERIOD OR THE DURATION OF THIS WARRANTY, WHICHEVER IS
SHORTER. Limitation of Special, Incidental or Consequential Damages. Please
note that some states/provinces (including Quebec) do not allow the exclusion
or limitation of special, incidental or consequential damages, so the below
limitations and exclusions may not apply to you. TO THE MAXIMUM EXTENT
PERMITTED BY APPLICABLE LAW, THIS WARRANTY DOES NOT COVER, AND DELTA FAUCET
COMPANY SHALL NOT BE LIABLE FOR, ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES (INCLUDING LABOR CHARGES TO REPAIR, REPLACE, INSTALL OR REMOVE THIS
PRODUCT), WHETHER ARISING OUT OF BREACH OF ANY EXPRESS OR IMPLIED WARRANTY,
BREACH OF CONTRACT, TORT, OR OTHERWISE. DELTA FAUCET COMPANY SHALL NOT BE
LIABLE FOR ANY DAMAGE TO THE ACCESSORY RESULTING FROM REASONABLE WEAR AND
TEAR, OUTDOOR USE, MISUSE (INCLUDING USE OF THE PRODUCT FOR AN UNINTENDED
APPLICATION), ABUSE, NEGLECT OR IMPROPER OR INCORRECTLY PERFORMED
INSTALLATION, MAINTENANCE OR REPAIR, INCLUDING FAILURE TO FOLLOW THE
APPLICABLE INSTALLATION, CARE AND CLEANING INSTRUCTIONS. Notice to residents
of the State of New Jersey: The provisions of this warranty, including its
limitations, are intended to apply to the fullest extent permitted by the laws
of the State of New Jersey.
Additional Rights. This warranty gives you specific legal rights, and you may
also have other rights which vary from state/province to state/province. This
is Delta Faucet Company’s exclusive written warranty and the warranty is not
transferable. If you have any questions or concerns regarding our warranty,
please contact us as provided above or view our Warranty FAQs
atwww.deltafaucet.com.
To reference replacement parts and access additional technical documents and product info, visit www.deltafaucet.com
1-800-345-DELTA (3358) www.deltafaucet.com/service-
parts
Image is for reference only
Register Online
www.deltafaucet.com/registerme
References
- Delta Faucet | Bathroom & Kitchen Faucets, Showers, Toilets, Parts, Accessories and More
- deltafaucet.com
- Register Your Delta Faucet Product | Delta Faucet
- Delta Faucet Support and Parts Resources
- Delta Faucet Contact Us Center & Support Resources
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>