HEINNER HDCH-5960RGBK Decorative Cooker Hood User Manual

: June 9, 2024
: HEINNER

Table of Contents

INTRODUCTION
CONTENT OF YOUR PACKAGE
SAFETY PRECAUTIONS
INSTALATION
OPERATION
TROUBLESHOOTING
CLEANING AND MAINTENANCE
TECHNICAL FICHE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

HEINNER HDCH-5960RGBK Decorative Cooker Hood User Manual

INTRODUCTION

Before using the appliance, please read carefully this instruction manual and keep it for future reference. This instruction manual is designed to provide you with all required instructions related to the installation, use and maintenance of the appliance. In order to operate the unit correctly and safety, please read this instruction manual carefully before installation and usage.

CONTENT OF YOUR PACKAGE

Decorative cooker hood
User manual
Warranty card

SAFETY PRECAUTIONS

This manual explains the proper installation and use of your cooker hood, please read it carefully before using even if you are familiar with the product. The manual should be kept in a safe place for future reference.

Never to do:

Do not try to use the cooker hood without the grease filters or if the filters are excessively greasy!
Do not install above a cooker with a high level grill.
Do not leave frying pans unattended during use because overheated fats or oils might catch fire.
Never leave naked flames under the cooker hood.
If the cooker hood is damaged, do not attempt to use.
Do not flambé under the cooker hood.
Caution: Accessible parts may become hot when used with cooking appliances.
The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the cooker hood. (When the cooker hood is located above a gas appliance, this distance shall be at least 65 cm).
The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels. Range hoods and other cooking fume extractors may adversely affect the safe operation of appliances burning gas or other fuels (including those in other rooms) due to back flow of combustion gases. These gases can potentially result in carbon monoxide poisoning. After installation of a range hood or other cooking fume extractor, the operation of open flued gas appliances should be tested by a competent person to ensure that back flow of combustion gases does not occur.

Always to do :

Important! Always switch off the electricity supply at the mains during installation and maintenance such as light bulb replacement
The cooker hood must be installed in accordance with the installation instructions and all measurements followed.
All installation work must be carried out by a competent person or qualified electrician.
Please dispose of the packing material carefully. Children are vulnerable to it.
Pay attention to the sharp edges inside the cooker hood especially during installation and cleaning.
Make sure the ducting has no bends sharper than 90 degrees as this will reduce the efficiency of the cooker hood.
Warning: Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.
Warning: Before obtaining access to terminals, all supply circuits must be disconnected.
Always put lids on pots and pans when cooking on a gas cooker.
When in extraction mode, air in the room is being removed by the cooker hood. Please make sure that proper ventilation measures are being observed. The cooker hood removes odours from room but not steam.
There shall be adequate ventilation of the room when the cooker hood is used at the same time as appliances burning gas or other fuels.
Cooker hood is for domestic use only.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
Caution: The appliance and its accessible parts can become hot during operation. Be careful to avoid touching the heating elements. Children younger than 8 years old should stay away unless they are under permanent supervision.
There is a fire risk if cleaning is not carried out in accordance with the instructions.
Regulations concerning the discharge of air have to be fulfilled.
Clean your appliance periodically by following the method given in the chapter Maintenance.
For safety reason, please use only the same size of fixing or mounting screw which are recommended in this instruction manual.
Regarding the details about the method and frequency of cleaning, please refer to maintenance and cleaning section in the instruction manual.
Cleaning and user maintenance shall not be made by children without supervision.
When the cooker hood and appliances supplied with energy other than electricity are simultaneously in operation, the negative pressure in the room must not exceed 4 Pa (4 x 10-5 bar).
Warning: Danger of fire. Do not store items on the cooking surfaces.
A steam cleaner is not to be used.
Never try to extinguish a fire with water, but switch off the appliance and then cover flame e.g. with a lid or a fire blanket.

INSTALATION

Mounting of the V-Flap

If the cooker hood does not have an assembled V-flap 1, you should mount the half-parts to its body. The images only show an example of how to mount the V-flap, because the outlet may vary according to different models and configurations. To mount the V-flap 1 you should:

Mount two half-parts 2 into the body 6.
The pin 3 should be top oriented.
The axis 4 should be inserted into the holes 5 on the body.
Repeat all the operations for the 2nd half-part.

Installation

If you have an outlet to the outside, your cooker hood can be connected as below picture by means of an extraction duct (enamel, aluminum, flexible pipe or non-flammable material with an interior diameter of 150 mm)

Before installation, turn the unit off and unplug it from the outlet.
The cooker hoods should be placed at a distance of 65-75cm from the cooking surface for best effect.
After deciding the cooker hood height, measure the position of the holes for hanging hood and inside chimney bracket. Drill 4 φ8 holes, 2 for inside chimney bracket and 2 for hanging the hood and keep the hood level. The fixed position of the inside chimney bracket is the highest place of inside chimney. **See Pic 2.

**

Screw 2 pcs ST4 x 30mm screws on the wall with wall plugs to fix the hood, then use 2 ST4 x 40mm screws to fix the inside chimney bracket. See Pic 2.
Install the V-flap and expansion pipe onto the cooker hood. Fix the expansion pipe on the outlet by cable tie. See Pic 3.
Install the outside chimney bracket onto the outside chimney with 2pcs ST4*8mm screws, here should be sure the inside chimney can be flexed freely inside **. See Pic 4.

**

Make the hood hang on the wall mounted screws in the fixed position, adjusting the cooker hood position, fix the cooker hood with 2 pcs ST4*30mm safety screws. See Pic 5.
Note: The two safety vents are positioned on the back housing, with diameter of 6mm.
Adjust the height of the inside chimney to the position of the inside chimney bracket and fix the inside chimney and outside chimney with 4pcs ST4*8mm screws. See Pic 6.

Hints for exhaust duct installation

The following rules must be strictly followed to obtain optimal air extraction:

Keep expansion pipe short and straight.
Do not reduce the size or restrict expansion pipe.
When using expansion pipe always install the pipe pulled taut to minimize pressure loss. Failure to observe these basic instructions will reduce the performance and increase noise levels of the cooker hood.
Any installation work must be carried out by a qualified electrician or competent person.
Do not connect the ducting system of the hood to any existing ventilation system which is being used for any other appliance, such as warmer tube, gas tube, hot wind tube.
The angle of the bend of the expansion pipe should not be less than 120º; you must direct the pipe horizontally, or, alternatively, the pipe should go up from the initial point and should be led to an outer wall.
After the installation, make sure that the cooker hood is level to avoid grease collection at on end.
Ensure the expansion pipe selected for installation complies with relevant standards and is fire retardant.

Warning

For safety reason, please use only the same size of fixing or mounting screws which are recommended in this instruction manual.
Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.

OPERATION

Press the “Power” button, the button controls the “on” & “off” of the hood.
Press the button “Speed” time after time, the motor runs as low / mid / high / low / mid…, the speed runs circularly; and the LED display will indicate as 1-2-3 1-2… circularly.
Press “Lamp” button, the light is on, press this button again, the light is off. Please note the Lamp is not under control of the on/off button.
When the hood is working, if press the “Timer” button, the hood will go into the status of acquiescent working (acquiescent time is 9mins), and then, LED display will be shown 9.8.7.6 …decreasing by 1, when time is up, the hood will be off automatically, and the lamp will extinguish. If pressing “Timer” button, the hood will go in or go out “Timer” function.

TROUBLESHOOTING

Fault	Possible Cause	Solution
Light on, but motor does not work	Fan switch turned off	Select a fan switch

position.
Fan switch failed| Contact service center.
Motor failed| Contact service center.
Light does not work, motor does not work| House fuses blown| Reset/Replace fuses.
Mains power cable is loose or disconnected| Refit mains power cable to power outlet. Switch power outlet on.
Oil leakage| One way valve and the outlet are not tightly sealed| Take down the one way valve and seal with sealant.
Leakage from the connection of chimney and cover| Take chimney down and seal.
Lights not working| Broken or faulty bulbs| Replace bulbs as per this instruction.
Insufficient suction| The distance between the cooker hood and the gas top is too far| Refit the cooker hood to the correct distance.
The Cooker hood inclines| The fixing screw is not tight enough| Tighten the hanging screw and make it horizontal.

Note: Any electrical repairs to this appliance must conform to your local, state and federal laws. Please contact the service centre if in any doubt before undertaking any of the above. Always disconnect the unit from the power source when opening the unit.

CLEANING AND MAINTENANCE

Caution

Before maintenance or cleaning is carried out, the cooker hood should be disconnected from the mains power supply. Ensure that the cooker hood is switched off at the wall socket and the plug removed.
External surfaces are susceptible to scratches and abrasions, so follow the cleaning instructions to ensure the best possible result is achieved without damage

GENERAL
Cleaning and maintenance should be carried out with the appliance cold especially when cleaning. Avoid leaving alkaline or acid substances (lemon juice, vinegar etc.) on the surfaces.
STAINLESS STEEL
The stainless steel must be cleaned regularly (e.g. weekly) to ensure a long life expectancy. Dry with a clean soft cloth. A specialized stainless steel cleaning fluid may be used.
Note: Ensure that wiping is done along with the grain of the stainless steel to prevent any unsightly crisscross scratching patterns from appearing.
CONTROL PANEL SURFACE
The inlay control panel can be cleaned using warm soapy water. Ensure the cloth is clean and well wrung before cleaning. Use a dry soft cloth to remove any excess moisture left after cleaning.
Important: Using neutral detergents and avoid using harsh cleaning chemicals, strong household detergents or products containing abrasives, as this will affectthe appearance of the appliance and potentially remove any printing of artwork on the control panel and will void manufactures warrantee.
GREASE MESH FILTERS
The mesh filters can be cleaned by hand. Soak them for about 3 minute in water with a mild detergent and then brush it gently with a soft brush. Do not apply too much pressure so as to avoid any damage to it. (Leave to dry naturally out of direct sun light) Filters should be washed separately to crockery and kitchen utensils. It is advisable not to use rinse aid

INSTALLING GREASE MESH FILTERS

To install filters for the following four steps:

Angle the filter into the slots at the back of the hood.
Push the button on the handle of the filter.
Release the handle once the filter fits into a resting position.
Repeat to install all filters

CARBON FILTER (not included in the package)

Activated carbon filter can be used to trap odors. Normally the activated carbon filter should be changed every 3 to 6 months according to your cooking habits. The installation procedure of activated carbon filter is as below:

Before installing or replacing the carbon filters, disconnect the mains power to the unit.
Press the filter lock and remove the mesh filter.
Turn the carbon filter on both side of the motor anti-clockwise. Replace the carbon filters with the new carbon filters.
Place the mesh filter.
Connect the power supply to the wall socket.

Note

Make sure the filter is securely locked. Otherwise, it would loosen and cause danger.
When activated carbon filter attached, the suction power will be lowered.

BULB REPLACEMENT

The bulb must be replaced by the authorized service or similarly qualified persons.
Always switch off the electricity supply before carrying out any operations on the appliance. When handling bulb, make sure it has completely cooled down before any direct contact with hands.
When handling bulbs hold with a cloth or gloves to ensure perspiration does not come in contact with the bulb as this can reduce the life of the bulb.

Note

Before changing the lights, make sure that the appliance is turned off and unplugged.
Protect against danger when changing lights, such as wearing gloves.

Changing the lights:

Open the glass and dismantle the grease filter. Put a hand into the cavity and gently push out the LED light. Pull the light outwards with another hand from the outside. Then dismantle the lamp wire terminal and take down the lamp for replacement.
Apply the reverse procedure for installation.
LED modules – round lamp
Max wattage: 2×1.5 W
Voltage range: DC 12V
Dimensions

TECHNICAL FICHE

Suction power:	562.9 m³/h
Motor	1 x 190W
Color	Black glass

Environment friendly disposal

You can help protect the environment! Please remember to respect the local regulations: hand in the non-working electrical equipment’s to an appropriate waste disposal center.

HEINNER is a registered trademark of Network One Distribution SRL. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from NETWORK ONE DISTRIBUTION