HEINNER HDCH-660TSS Decorative Cooker Hood User Manual

HDCH-660TSS Decorative Cooker Hood
User Manualwww.heinner.com

• Decorative cooker hood
• Suction power: 586.3 m³/h
• Color: stainless steel

Thank you for purchasing this product!

INTRODUCTION

Before using the appliance, please read carefully this instruction manual and keep it for future reference.
This instruction manual is designed to provide you with all required instructions related to the installation, use and maintenance of the appliance.
In order to operate the unit correctly and safety, please read this instruction manual carefully before installation and usage.

SAFETY PRECAUTIONS

CONTENT OF YOUR PACKAGE

➢ Decorative cooker hood
➢ User manual
➢ Warranty card
This manual explains the proper installation and use of your cooker hood, please read it carefully before using even if you are familiar with the product. The manual should be kept in a safe place for future reference.
Never to do:

• Do not try to use the cooker hood without the grease filters or if the filters are excessively greasy!

• Do not install above a cooker with a high level grill.

• Do not leave frying pans unattended during use because overheated fats or oils might catch fire.

• Never leave naked flames under the cooker hood.

• If the cooker hood is damaged, do not attempt to use.

• Do not flambé under the cooker hood.

• Caution: Accessible parts may become hot when used with cooking appliances.

• The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the cooker hood. (When the cooker hood is located above a gas appliance, this distance shall be at least 65 cm).

• The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels. Range hoods and other cooking fume extractors  may adversely affect the safe operation of appliances burning gas or other fuels (including those in other rooms) due to back flow of combustion gases.
  These gases can potentially result in carbon monoxide poisoning. After installation of a range hood or other cooking fume extractor, the operation of open flued gas appliances should be tested by a competent person to ensure that back flow of combustion gases does not occur.

Always to do:

• Important! Always switch off the electricity supply at the mains during installation and maintenance such as light bulb replacement.
• The cooker hood must be installed in accordance with the installation instructions and all measurements followed.
• All installation work must be carried out by a competent person or qualified electrician.
• Please dispose of the packing material carefully. Children are vulnerable to it.
• Pay attention to the sharp edges inside the cooker hood especially during installation and cleaning.
• Make sure the ducting has no bends sharper than 90 degrees as this will reduce the efficiency of the cooker hood.
• Warning: Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.

INSTALATION

Mounting of the V-Flap
If the cooker hood does not have an assembled V-flap 1, you should mount the half-parts to its body. The images only show an example of how to mount the V-flap, because  the outlet may vary according to different models and configurations.
To mount the V-flap 1 you should:

• Mount two half-parts 2 into the body 6.
• The pin 3 should be top oriented.
• The axis 4 should be inserted into the holes 5 on the body.
• Repeat all the operations for the 2nd half-part.

Installation
If you have an outlet to the outside, your cooker hood can be connected as below picture by means of an extraction duct (enamel, aluminum, flexible pipe or non-flammable material with an interior diameter of 150 mm).

1. Before installation, turn the unit off and unplug it from the outlet.

2. The cooker hoods should be placed at a distance of 65-75cm from the cooking surface for best effect.

3. Install the hook on a suitable place once the installation height is fixed and keep it in line. The fixed position of the inside chimney bracket is the place of chimney. See  Pic 2.

4. . Fix the outside chimney bracket on the outside chimney and be sure that the inside chimney can be adjusted the height in it freely as well as fixing the expansion pipe.
   Afterwards, install the expansion pipe and chimney on the cooker hood. Fix the expansion pipe with a cable tie on the outlet. See Pic3/Pic4.
   

5. Put the cooker hood on the hook. See Pic 5.
   

6. Adjust the height of the inside chimney to the position of the inside chimney bracket and fix it with screws, after adjusting the position, fix the body with safety screws.  Note: The two safety vents are positioned on the back housing, with a diameter of 6mm. See Pic 6 & 7.

Hints for exhaust duct installation
The following rules must be strictly followed to obtain optimal air extraction:

• Keep expansion pipe short and straight.
• Do not reduce the size or restrict expansion pipe.
• When using expansion pipe always install the pipe pulled taut to minimize pressure loss. Failure to observe these basic instructions will reduce the performance and  increase noise levels of the cooker hood.
• Any installation work must be carried out by a qualified electrician or competent person.
• Do not connect the ducting system of the hood to any existing ventilation system which is being used for any other appliance, such as warmer tube, gas tube, hot wind tube.
• The angle of the bend of the expansion pipe should not be less than 120º; you must direct the pipe horizontally, or, alternatively, the pipe should go up from the initial  point and should be led to an outer wall.
• After the installation, make sure that the cooker hood is level to avoid grease collection at on end.
• Ensure the expansion pipe selected for installation complies with relevant standards and is fire retardant.
  

Warning:
➢ For safety reason, please use only the same size of fixing or mounting screws which are recommended in this instruction manual.
➢ Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.

OPERATION

Push button

1. Push the stop button, and the motor will stop.
2. Push the low button, and the motor will run at low speed.
3. Push the middle button, and the motor will run at mid speed.
4. Push the high button, and the motor will run at high speed.
5. Push the lamp button and the two lights will illuminate. Push it again and the light will turn off.

TROUBLESHOOTING

Light on, but
motor does not
work| Fan switch turned off| Select a fan switch position.
Fan switch failed| Contact service center.
Motor failed| Contact service center.
Light does not
work, motor does
not work| House fuses blown| Reset/Replace fuses.
Mains power cable is loose or disconnected| Refit mains power cable to power outlet. Switch power outlet on.
Oil leakage| One way valve and the outlet are not
tightly sealed| Take down the one way valve and seal with sealant.
Leakage from the connection of chimney
and cover| Take chimney down and seal.
Lights not
working| Broken or faulty bulbs| Replace bulbs as per this instruction.
Insufficient
suction| The distance between the cooker hood and
the gas top is too far| Refit the cooker hood to the correct distance.
The Cooker hood
inclines| The fixing screw is not tight enough| lighten the hanging screw and make it horizontal.

Note: Any electrical repairs to this appliance must conform to your local, state and federal laws. Please contact the service centre if in any doubt before undertaking any of the above. Always disconnect the unit from the power source when opening the unit.

CLEANING AND MAINTENANCE

Caution:

• Before maintenance or cleaning is carried out, the cooker hood should be disconnected from the mains power supply. Ensure that the cooker hood is switched off at the  wall socket and the plug removed.
• External surfaces are susceptible to scratches and abrasions, so follow the cleaning instructions to ensure the best possible result is achieved without damage.

GENERAL
Cleaning and maintenance should be carried out with the appliance cold especially when cleaning. Avoid leaving alkaline or acid substances (lemon juice, vinegar etc.) on the surfaces.
STAINLESS STEEL
The stainless steel must be cleaned regularly (e.g. weekly) to ensure a long life expectancy. Dry with a clean soft cloth. A specialized stainless steel cleaning fluid may be used.
Note: Ensure that wiping is done along with the grain of the stainless steel to prevent any unsightly crisscross scratching patterns from appearing.
CONTROL PANEL SURFACE
The inlay control panel can be cleaned using warm soapy water. Ensure the cloth is clean and well wrung before cleaning. Use a dry soft cloth to remove any excess moisture  left after cleaning.
Important: Using neutral detergents and avoid using harsh cleaning chemicals, strong household detergents or products containing abrasives, as this will affect the appearance  of the appliance and potentially remove any printing of artwork on the control panel and will void manufactures warrantee.
GREASE MESH FILTERS
The mesh filters can be cleaned by hand. Soak them for about 3 minute in water with a mild detergent and then brush it gently with a soft brush. Do not apply too much pressure so as to avoid any damage to it. (Leave to dry naturally out of direct sun light)
Filters should be washed separately to crockery and kitchen utensils. It is advisable not to use rinse aid. 

INSTALLING GREASE MESH FILTERS
To install filters for the following four steps:

• Angle the filter into the slots at the back of the hood.
• Push the button on the handle of the filter.
• Release the handle once the filter fits into a resting position.
• Repeat to install all filters.

CARBON FILTER (not included in the package)
Activated carbon filter can be used to trap odors. Normally the activated carbon filter should be changed every 3 to 6 months according to your cooking habits. The  installation procedure of activated carbon filter is as below:

1. Before installing or replacing the carbon filters, disconnect the mains power to the unit.
2. Press the filter lock and remove the mesh filter.
3. Turn the carbon filter on both side of the motor anti-clockwise. Replace the carbon filters with the new carbon filters.
4. Place the mesh filter.
5. Connect the power supply to the wall socket.

Note:

• Make sure the filter is securely locked. Otherwise, it would loosen and cause danger.
• When activated carbon filter attached, the suction power will be lowered.

BULB REPLACEMENT

• The bulb must be replaced by the authorized service or similarly qualified persons.
• Always switch off the electricity supply before carrying out any operations on the appliance. When handling bulb, make sure it has completely cooled down before any  direct contact with hands.
• When handling bulbs hold with a cloth or gloves to ensure perspiration does not come in contact with the bulb as this can reduce the life of the bulb.

Note:

• Before changing the lights, make sure that the appliance is turned off and unplugged.
• Protect against danger when changing lights, such as wearing gloves.

Changing the lights:

• Remove the grease filter.
• Find out the junction box, unscrew the screws on the junction box cover, then take down the junction box cover (If there is wire pressing plate which pressed
  the light wire, the wire pressing plate needs to be dismantled first). See Pic

1. The junction box has version a and b, depending on different models.

• Find out the terminal of the light connecting wire and pull it out. See Pic 2.

• Use a tool or the hand to press the spring splinter of both sides of LED light to the inside, until the light is pressed out, then slightly pull the light connecting wire out.
  See Pic 3.

• Apply the reverse procedure to install the light back.
  – LED modules – round lamp
  – Max wattage: 2×1.5 W
  – Voltage range: AC 220-240V
  – Dimensions
  

TECHNICAL FICHE

Environment friendly disposal
You can help protect the environment!
Please remember to respect the local regulations: hand in the non-working electrical equipment’s to an appropriate waste disposal center.

HEINNER is a registered trademark of Network One Distribution SRL. Other brands and product names are trademarks or registered trademarks of their respective  holders.
No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without  permission from NETWORK ONE DISTRIBUTION.
Copyright © 2013 Network One Distribution. All rights reserved.
www.heinner.com, http://www.nod.ro
This product is in conformity with norms and standards of European Community.

Importer: Network One Distribution
Marcel Iancu Street, 3-5, Bucharest, Romania
Tel: +40 21 211 18 56, www.heinner.com , www.nod.ro

References

• Heinner – large appliances, small appliances, housekeeping, DIY
• Heinner – large appliances, small appliances, housekeeping, DIY
• NOD - Network One Distribution
• NOD - Network One Distribution

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>