lorelli Infinity Baby Stroller Instruction Manual

lorelli Infinity Baby Stroller

SAFETY REQUIREMENT

1. This vehicle is suitable for children with a weight up to 22 kg or 4 years whichever comes first! Summer basket: Age6+m.
2. The height of the carried child in the stroller should not exceed 104 cm!
3. Use parking device if you do not hold the stroller with hand!
4. Do not leave the stroller on hills or inclined surfaces even if you have activated the parking system!
5. Parking device shall be engaged when placing and removing the children!
6. The shopping basket can take a maximum load of 2 kg!
7. Any load attached to the handle and/or on the back of the backrest and/or on the sides of the vehicle will affect the stability of the vehicle! Maximum load of the accessory bag 1 kg. Do not hang any additional bags!
8. Regularly check for loose parts! Make routine inspection, regularly maintain, clean and/or wash the vehicle!
9. The vehicle shall be used only for 1 child!
10.  Accessories which are not approved by the manufacturer shall not be used!
11.  Only spare parts delivered or recommended by the manufacturer/ distributor can be used!
12.  Make sure that the safety belts are placed properly!
13.  The stroller should always be used under the supervision of an adult!
14. Do not allow children to suspend him/herself or play in the stroller!
15.  Do not allow children to stand in the stroller!
16.  Do not allow your child to stand on the seat and foot rest!
17. Do not use the stroller on uneven surfaces near fire or other dangerous places!
18. Do not use the stroller on stairs and escalators!
19. Fold the stroller before go upstairs and downstairs. Mounting the stroller on stairs, pavements and others with the child in it and by pushing the handle causes deformation of the stroller and is out of warranty repair!
20.  Adjusting of the back rest must be made only by a person read carefully the instruction rules for adjusting!
21. Any additional baggage left in the stroller may cause it to become unstable!
22. The person who assembles the stroller must be familiarized with its functions!
23. The front bar can not be used as a carry handle!
24. The chassis of this vehicle is compatible with a pram body ,,Infinity” and with a car seat,,lnfinity”.

WARNING

1. WARNING! Never leave the child unattended!
2.  WARNING! Ensure that all the locking devices are engaged before use!
3. WARNING! To avoid injury ensure that the child is kept away when unfolding and folding this product!
4. WARNING! Do not let the child play with this product!
5. WARNING! This seat unit ( summer basket) is not suitable for children under 6 months!
6. WARNING! Always use the restraint system!
7. WARNING! Check that the pram body or seat unit or car seat attachment devices are correctly engaged before use!
8. WARNING! This product is not suitable for running or skating!
9. WARNING!No additional mattress/ cushion shall be added.
10.  WARNING! Always use the crotch belt in combination with the waist belt! To prevent injury from a fall or a slip off always use the shoulder straps!
11. WARNING! Keep away from fire !
12.  WARNING! This pram body is designed to be used from baby’s birth.
13.  WARNING! The pram body shall not be used, as soon as the child is able to sit by himself, roll over and can push itself up on its hands and knees. Maximum weight of the child: 9 kg
14.  WARNING! When using the car seat: This vehicle does not replace a cot or a bed. Should your child need to sleep, then it should be placed in a suitable pram body, cot or bed.
15. WARNING! The images on the front page and inside the manual are for illustrative purposes and may differ from the actual product. EN 1888-2:2018

PARTS

1. Metal frame of the stroller
2.  Shopping basket
3. Back wheels
4.  Frontwhools
5. Summer seat
6. Bumper bar
7. Canopy
8. Seat footmuff
9. Accessory bag
10. body with mattress and carrying handle
11. Pram body cover
12. Pram body adapters
13. Car seal
14.  Car seat adapters
15.  Cup holder

UNFOLDING

1. Folded stroller (Figure 2)
2. Lirt lhe handle or the stroller up, lhe stroller will unfold and lock in place aulomalically. (Figure 3)

ASSEMBLING

1. Install the front wheels by pressing the console button and pushing them up until they lock in place (Figure 4 ). Ensure that they ate securely locked in place. To remove, press the console button and pull the wheel downwards. (Figure 5)
2. Install the rear wheels as shown in Figure 6 To remove, pull the rear axle button and pull the wheel off. (Figure 7)
3. If Install the stroller seat in the frame as shown in Figure 8. If you hear a click, it means that the seat is fixed in place. To remove, press the buttons on both sides of the seat at the same time and pull upwards (Picture 9). The seat can be inslalled lo face lhe front or the rear.
4. Install the bumper bar. To remove the bumper bar, press the buttons on both sides and pull. (Figure 10)
5. The bottle holder is mounted on the right side of the frame. (Figure 11)

EXPLOITATION

1. To lock the stroller in place, use the brakes on the rear wheels by pressing the brake pedal, located on the rear axle (Figure 12) To release the brake, raise the brake pedal with your foot.

2.  You can adjust the handle by pressing both buttons on the side and pushing up and down. (Figure 13)

3. While pushing the stroller on rough and uneven surfaces, you can use the straight-line option by pressing the button to lock the front wheels. To release the front wheels, lift the lock button. (Figure 14)

4. To adjust (lower) the canopy, grab its upper part and pull it down to the desired position. (Figure 15)

5. When using lhe seat, ii is MANDATORY to pul lhe child’s safety harness on!

6. Attach the shoulder and abdominal straps and place them in the central locking buckle (Figure 16). Adjust the length of the harness straps by pulling the buckles (Figure 17). To release the harness, press on the central buckle button. (Figure 16)

7. Adjusting tho footrest To change tho position of tho footrest, pross both buttons simultaneously and adjust (Figure 18). ATTENTION! Failure to observe this instruction will damage the locking mechanisms and will not be subject to warranty!

8. If You can adjust the position of the backrest by pulling up the handle to unlock the mechanism located on the back and placing it in the desired position. (Figure 19)
   ATTENTION! If you try to adjust the backrest without unlocking the mechanism and apply excessive force, the unlocking mechanism may become deformed, which is not subject to warranty!
   Attention! The brake does not guarantee optimal power when on steep inclines! Therefore, never leave the stroller on an inclined surface with a child sitting or lying in the stroller!
   WARNING! The brake on your slroller is a lype of parking device. To activate lhe brake, lhe stroller must be stationary. Carefully press the brake pedal, while gently pushing the stroller front-and-back to synchronize the braking device and for more secure activation of the braking mechanism.

9. If you want, you can attach the footmuff to the seat by slipping it under the footrest and fastening to the upholstery and the canopy.

FOLDING

1. Apply the stroller’s brakes
2. Fold the canopy as much as possible.
3. Fold the backrest as far as possible to the front, to that ii rests against the bumper bar.
4. Pull the mechanisms located on both sides of the handle and push it down. (Figure 20)
5. Aproperly folded stroller should look as shown in Figure 21.

PRAM BODY

ATTENTION, for the correct preparation of the pram body for a newborn after removing ii from the transport box, perform the following actions:

1. Place the cot on a table and remove the mattress and fabric liner.
2.  With one hand lift the metal frame on one side of the pram body. (Figure 22)
3.  With the other hand press the bottom and hold the metal support.
4. Pressing the bottom, grasp the support strap and pull it towards the outside of the pram body until it reaches the limiters. (Figure 23)
5.  Repeat this procedure with the other support, until the cot is fully expanded; it must look as in Figure 24.
6. Replace the mattress and the fabric liner.
7. Lift up the carrying handle until you hear a click. (Figure 25)
8. To fold the carrying handle, press both buttons on the inside at the base of the handle with your thumbs at the same time. (Figure 26)
9. Install the pram body adapters by sliding them from left to right on the designated places, as indicated in figure 27.
10.  Install the pram body on the stroller, ensuring that the adapters are positioned and locked in the intended holes in the frame (Figure 28). The click means that the basket is locked in place. In order to remove, simultaneously press the buttons on both sides of the pram body and pull up (Figure 29). The pram body should only be installed facing the parents (Figure 28).
11.  Finally, place the footmuff and fasten it with a zipper and buttons onto the pram body.
12. The pram body should be parent-facing

MAINTENANCE CARE

1.  To clean the metal parts, clean with a wet cloth and wipe dry.
2. To clean the plastic parts, use a towel, water and a soft detergent.
3. To clean the textile parts, use a solution for cleaning of upholsteries.
4. When not in use, never place other objects in or on the stroller!
5. Always dry and air the stroller if it gets wet.
6.  Run regular clean-ups over the wheel axes and the plastic elements.
7. Always clean the wheel axes and the plastic elements after using the stroller on sandy or dusty surfaces!
8.  DO NOT LUBRICATE the wheel axes or other movable parts of the stroller! Just clean them!
9. Run regular checks for loose or damaged parts and if there are such parts, immediately replace them with new ones

NOTICE

1. This is a ‘Universal’ child restraint. It is approved to Regulation No 44, 04 series of amendments, for general use in vehicles and it will fit most, but not all, car seats.
2. A correct fit is likely if the vehicle manufacturer has declared in the vehicle handbook that the vehicle is capable of accepting a ‘Universal’ child restraint for this age group.
3. This child restraint has been classified as ‘Universal’ under more stringent conditions than those which applied to earlier designs which do not carry this notice.
4. If in doubt, consult either the child restraint manufacturer or the retailer.

Appropriate only if the approved vehicles are equipped with three-point / retractor safety belts approved in accordance with UNECE Regulation NQ 16 or other equivalent standards.

EXTREMELY DANGEROUS!
Do not place the rear-facing child seat on front seat with airbag. Death or serious injury can occur.

Important safety instructions
Please read the instructions carefully. because improper installation may cause serious injury. in this case, the manufacturer is not responsible.

1. WARNING! The car seat can not be used forward facing!

2. WARNING! The rigid items and plastic parts of a child restraint shall be so located and installed that they are not liable, during everyday use of the vehicle, to become trapped by a movable seat or in a door of the vehicle. Prevent harness/vehicle belt from getting trapped between car doors or rubbing against sharp parts of the seat or body.

3. WARNING! All straps holding the restraint to the vehicle should be tight, all straps restraining the child should be adjusted to the child’s body. The straps should not be twisted! Always make sure that the seat harness and vehicle belt are correctly tensioned to ensure maximum protection for your child.

4. WARNING! The device should be changed when it has been subject to violent stresses in an accident. After an accident, replace your child restraint and the vehicle seat belts. Although they may look undamaged, they may not protect your child as well as they should.

5. WARNING! Follow closely the instructions for installation. Failure can result in injury to the child!

6. WARNING! It is dangerous to make any alterations or additions to the device without the approval of the Type Approval Authority. Your child is in danger if you don’t follow closely the installation instructions provided by the child restraint manufacturer.

7. WARNING! Do not use any load bearing contact points other than those described in the instructions and marked in the child restrained. Ensure the vehicle seat belt buckle is connected to the correct main load bearing contact point which is intended for the occupied vehicle seat. Ensure the buckle and the seat belt of the vehicle do not interfere with the main load bearing contact points of the child restrained system. Ensure you are following the correct way path of the vehicle’s safety belt by the installation of the restrained system and by the restraining of the child. On this way you will avoid an unsatisfactory position of the adult safety belt buckle relative to the main load bearing contact points on the restraint. Please contact the child restraint manufacturer if in doubt about this point.

8. WARNING! Rearward child restraint systems should not be used in seats protected by an airbag.

9.  WARNING! NEVER leave your child unattended in the safety device, even for the shortest time!

10. WARNING! Any luggage or other objects liable to cause injuries in the event of a collision shall be properly secured.

11.  WARNING! Do not use the child restraint system without the cover.

12. WARNING! Do not replace the seat cover with any other than the one recommended by the manufacturer, because the cover constitutes an integral part of the restraint performance.

13.  WARNING: DO NOT attempt to dismantle, modify or add any parts to the car seat or change the way your vehicle seat belts are made or used.

14. WARNING! Do not leave the buckle in a partially closed position and it must only lock when all parts are engaged. It must be possible to release the child from the restraint immediately in an emergency.

15. WARNING! Install the child restraint in vehicle seating positions categorized as ‘Universal’ in the vehicle owner’s manual, by using the primary belt route.

16. WARNING! If the chair is not provided with a textile cover, keep it away from sunlight, otherwise it may be too hot for the child’s skin. If the vehicle has been left in the sun for a long time, check the seat cover and make sure it is not too hot before placing the child in the child cushion.

17. WARNING! Do not use the car seat in the house. It is not designed for home use and should only be used in the vehicle!

18. WARNING! Periodically check the belts for wear, paying special attention to the points of attachment, protections and regulating devices. If the harness / vehicles belts becomes cut or frayed, replace it before traveling.

19. WARNING: ALWAYS secure your child with the safety belts when using the car seat.

20. WARNING! Do not leave the buckle in a partially closed position and it must only lock when all parts are engaged. It must be possible to release the child from the restraint immediately in an emergency. Your child must be taught never to play withthe buckle. The buckle is NOT CHILD PROOF.

21. WARNING! The baby seat must be secured with car safety belt, even when it is not in use.
    An unsecured seat may injure other passengers in the car in an urgent stop.

22. WARNING! Store this child seat in a safe place when it is not being used.Avoid placing heavy objects on top of it. Do not allow your child seat to come into contact with corrosive substances e.g. battery acid.

23. WARNING! Do not leave your child in this safety seat for a long period of time. By long trips make more breaks and take out the child from the safety seat.

24. WARNING! Security is only guaranteed if the child restraint is fitted in accordance with these instructions.

25. WARNING! The instruction must be retained on the child restraint for its life period

26. Images on the title page and in the instruction manual are only illustrative and may differ from the real product.

WASHING INSTRUCTIONS

1. The car seat can be cleaned using lukewarm water and soap. Do not use aggressive cleaners like abrasives or thinner.
2. The cover should be washed by hand at a maximum temperature of 30’C. Do not put in the dryer, just airing it.
3. The plastic parts can be cleaned by using a wettish drapery. Please, do not use any solvate.

TYPES OF APPROVED BELTS TO HAVE IN THE CAR

• A – Car safety belt – Diagonal Belt
• B – Car safety belt – Lap Belt

Your child seat can be installed ONLY with the help of 3-point belts!!! ONLY in the OPPOSITE direction of movement of the car! ® Possibility to install ONLY on seats with 3-point seat belts!

Parts

1. Carrying handle
2. Belt softener
3. Belt buckles
4. 3 Button for adjusting the belt (under the cover)
5. Strap for belts adjustment
6. Baby Insert
7. Shoulder straps
8. Buckle Pads
9.  Canopy
10. Red button for handle adjusting
11. Diagonal belt guide
12. Lap belt guide
13. Shell
14. Adaptors
15. Openings for shoulder straps
16. Cover

Check the height of the shoulder straps.
Always check that the shoulder straps are placed at the correct height for your child. Choose the height of the straps depending on the height of the child, they must be positioned at the level of the child’s shoulders or slightly above.
Attention: Do not place the straps too high or so that the child is leaning on them. There are pairs of holes on the back of the seat which you can use to adjust the height of the shoulder straps to the weight of the child. (Figure 4)

SAFETY INSTRUCTION

Adjusting the height of the straps.

1. Release the shoulder straps by pressing the belt adjustment button “4” and pulling the shoulder straps.(Figuro 3)
2. Unclip the strap buckles from the centre buckle and pull the two straps from the back of the backrest, then move them to the next position.

Fastening the harness.

1. Connect the two elements “E” and “F” at the end of the strap (Figure 5) and place them in the central buckle “3” until a click is heard.

2. Tightening the straps: Place the child in the seat, fasten the two straps in the centre buckle and pull the strap in the middle of the seat “5” . (Figure 8)
   Upholstery removal To remove the seat upholstery, first remove the harness. The upholstery of the seat is held in place with plastic clips on each side of the car seat (Figure 17). For children weighing up to 10 kg, the car seat should be used with the padded liner. When the child’s weight is between 10 kg and 13 kg, you must remove the padded liner. Release the straps from the buckle and remove the padded liner. Remove the canopy- Pull lhe small bullons on each side or the canopy and pull it out of lhe holder. (Figure 16) Adjusting the handle for carrying the car seat The handle for carrying the car seat can be adjusted in 4 positions. To adjust the handle, press the red buttons on both sides of the handle at the same time and turn. (Figure 9)

   • Position 1 Forward-facing – for installing in tho car. Only this position can bo usod whon tho soat is installed in the car. (Figure 10)
   • Position 2 Upright- to carry.
   • Position 3- Fixed horizontally behind the back- For rocking seat function.
   • Position 4- Down behind lhe back- Fixing the seat upright lo feed the child.

Make sure the handle is locked in the selected position, the seat harness is in place and the buckle is fastened before carrying your child in the car seat.

WARNING: The car seat should only be installed facing the parents, as shown in figure 19. Installing Hold the car seat facing the handle of the stroller.

Place the car seat adapters (A) on the mounting points (B). Position the car seat guides (A) above the mounting points (B) and press down until a “Click” is heard Figure 18. Pull up the car seat to make sure it is securely attached to the stroller frame. Removal – to remove the car seat, simultaneously press the buttons on both sides and pull up- Figure 19.
Please use the car’s 3-point seat belts to ensure the safety of the child and secure the car seat! Your car seat can be installed ONLY with using a 3-point belt and rear facing.

ATTENTION: The car seat must not touch the front passenger seat. (Figure 11)

• Step 1. Adjust the handle to front position. (Figure 10)
• Step 2. Place the child seal on lhe car seat facing the rear, ensuring that it is snug against the backresL The car seat should only be used on the back seats of the car! (Figure 12)
• Step 3. Pass the lap belt through the two guides on the sides of the child seat. (Figure 13) Fasten the seat belt in the car buckle until a “click” is heard. Pull the shoulder strap up to tighten the child seat to the car seat and make suro tho bolt is fastonod.
• Step 4. Place the shoulder belt in the guide on the back of the child seat. (Figure 14)
• Step 5. Pull the shoulder strap to tighten it.
• Step 6. Ensure that the seat is securely fastened to the car seat and that the belt is taut and not twisted. (Figure 15)
• Step 7. Place the child in the chair. Check the height of the shoulder straps. Make sure the belts are not twisted or caught on anything. Fasten the child ‘s safety harness, making sure they are secure, and pull the strap in the centre of the seat.

Didis Ltd.
Bulgaria Shumrn, 6 Trnki;,-i7tok Street Phone: +1595411501130
e-mails: home.market@didis-ltd.com; export@didis-ltd.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>