FISHER PAYKEL RB36S Integrated CoolDrawer Multi-Temperature Drawer Installation Guide

June 5, 2024
Fisher & Paykel

FISHER PAYKEL RB36S Integrated CoolDrawer Multi-Temperature Drawer

FISHER-PAYKEL-RB36S-Integrated-CoolDrawer-Multi-Temperature-Drawer-
image

SAFETY AND WARNINGS

WARNING!
Electric Shock Hazard
Failure to follow this advice may result in electrical shock or death.

  • Read and follow the safety and warnings outlined in this installation guide before operating this appliance.

WARNING!
Cut Hazard
Failure to use caution could result in injury.

  • Take care: panel edges may be sharp.
  • Do not put fingers in the drawers when closing.

WARNING!
Tip Hazard

  • Do not operate this appliance until it has been securely anchored inside the cabinetry.

To ensure that the appliance is stable under all loading conditions:

  • The appliance must be securely anchored to the floor by a professional installer according to the installation steps in this guide.

WARNING!
To avoid hazard, follow these instructions carefully before Installing or using this appliance.

  • Please make this information available to the persons installing the appliance.
  • Assume all electrical parts are live.
  • Disconnect power supply before servicing and installation.

BEFORE INSTALLATION

  • The appliance must be installed by a qualified installer, or Fisher and Paykel trained and supported service technician to avoid faulty electrical connection.
  • All connections for electrical power and grounding must comply with local codes and ordinances and be made by licensed personnel when required.
  • Avoid installation of the appliance/s under a ground fault circuit interrupter (GFCI).
  • Ensure the appliance is installed properly. Improper installation that results in appliance failure is not covered under the appliance warranty.

UNPACKING

  • Remove all packaging materials supplied with the appliance.
  • Avoid scratching the surface of your appliance when moving or installing.
  • If the appliance is damaged, contact your Fisher and Paykel dealer.
  • Ensure all components and accessories are complete.

ELECTRICAL/PLUMBING

  • We recommend to locate the electrical connection of the appliance in an adjacent area or unit (cabinet or cupboard) that are easily accessible in case of repair or disconnection.
  • Ensure the power outlet is located outside the cavity, within 72 13/16″ (1850mm) from the CoolDrawer™ cavity if situated on the left-hand side of the cavity, and within 49 3/16″ (1250mm) if situated on the right-hand side of the cavity.
  • The services hole in the cavity needs to be large enough for the power supply plug to fit through.

INSTALLATION

  • The installation bracket and fittings supplied must be fitted to the wall of the finished enclosure to withstand a 100kg load.
  • Ensure that the installation bracket is installed correctly to prevent the possibility of the appliance tipping forward when the drawer is open.
  • Ensure the power cord is not run over or damaged when installing the product into the cabinetry.
  • For flush installation, ensure the drawer panel is installed flush with cabinetry front surface. Ensure the appliance is properly centered.
  • Complete the final checklist after installation is complete.
  • Protect the finish of the Fisher and Paykel Stainless Steel door panel from any scratch or damage.
  • If using Custom door panels, ensure they are prepared as per ‘Custom door panel install dimensions’ section.
  • The thickness of the custom door panel can vary as long as the screws do not penetrate beyond the full depth of the door panel, and as long as the overall weight of door panel does not exceed the allowable weight. Refer to ‘Door panel dimensions’ for maximum door panel weight of your product.

INTEGRATED COOLDRAWER™

FISHER-PAYKEL-RB36S-Integrated-CoolDrawer-Multi-
Temperature-Drawer-fig1

SUPPLIED PARTS

FISHER-PAYKEL-RB36S-Integrated-CoolDrawer-Multi-Temperature-Drawer-
fig2

DRAWER PANELS

The Stainless steel drawer panel is not supplied and must be purchased separately through an authorised Fisher and Paykel dealer. Visit fisherpaykel.com for more information.

ContemporaryFISHER-PAYKEL-RB36S-Integrated-CoolDrawer-Multi-Temperature-
Drawer-fig3 Professional FISHER-PAYKEL-RB36S-Integrated-CoolDrawer-Multi-Temperature-Drawer-
fig5

HANDLE KIT

The handle kit is not supplied and must be purchased separately through an authorised Fisher & Paykel dealer. Visit fisherpaykel.com for more information.

ContemporaryFISHER-PAYKEL-RB36S-Integrated-CoolDrawer-Multi-Temperature-
Drawer-fig41 Professional FISHER-PAYKEL-RB36S-Integrated-CoolDrawer-Multi-Temperature-Drawer-
fig6

DIMENSIONS

PRODUCT DIMENSIONS

FISHER-PAYKEL-RB36S-Integrated-CoolDrawer-Multi-Temperature-Drawer-
fig7FISHER-PAYKEL-RB36S-
Integrated-CoolDrawer-Multi-Temperature-Drawer-fig8 * Does not include Stainless steel or custom door panel, false panel and handle. **Includes power terminal.

STAINLESS STEEL PANEL DIMENSIONSFISHER-PAYKEL-RB36S-Integrated-
CoolDrawer-Multi-Temperature-Drawer-fig9FISHER-PAYKEL-RB36S-Integrated-CoolDrawer-Multi-
Temperature-Drawer-fig10

CUSTOM PANEL DIMENSIONS — SINGLE PANELFISHER-PAYKEL-RB36S-Integrated-
CoolDrawer-Multi-Temperature-Drawer-fig11

CUSTOM PANEL DIMENSIONS — DUAL PANELFISHER-PAYKEL-RB36S-Integrated-
CoolDrawer-Multi-Temperature-Drawer-fig13

CLEARANCE  DIMENSIONS IN| MM
---|---
G Clearance between top of drawer panel and 1/16| 2
H Clearance between front end of benchtop to                              max 3/16| max 20
I Gap between drawer panel and false panel 3/16| 4
J Depth from back of drawer panel/false panel to                         min 1 9/16| min 40
K Height for ventilation* min 2| min 50

CABINETRY DIMENSIONS — FRAMEDFISHER-PAYKEL-RB36S-Integrated-CoolDrawer-
Multi-Temperature-Drawer-fig15FISHER-PAYKEL-RB36S-Integrated-CoolDrawer-
Multi-Temperature-Drawer-fig16

CABINETRY DIMENSIONS — FRAMELESSFISHER-PAYKEL-RB36S-Integrated-
CoolDrawer-Multi-Temperature-Drawer-fig17 FISHER-PAYKEL-RB36S-Integrated-CoolDrawer-
Multi-Temperature-Drawer-fig18

ELECTRICAL CONNECTION

Services can be located on either side of the CoolDrawerTM. Disconnect power to surrounding appliances before preparing the cavity. FISHER-PAYKEL-RB36S-
Integrated-CoolDrawer-Multi-Temperature-Drawer-fig19

CABINETRY PREPARATION

INSTALL BRACKETS

  1. Locate the brackets to the top of each spacer.
    Ensure there is 1″ (25mm) clearance between the front end of the cabinetry frame and the front of the bracket.

  2. Secure each bracket to the spacer with countersunk screws (3x).

ATTACH VENT DUCTS

  1. Locate the vent ducts to the slots in the cabinetry frame.
  2. Cut each vent duct to be flush with the top of the spacer.
  3. Smooth the sharp edges with a file or similar tool.
  4. Secure the vent ducts by fixing with screws.

PANEL PREPARATION

STAINLESS STEEL PANEL

  1. Locate the top attachment hooks (2x) in correct orientation to the screw holes at the back of drawer panel*, and secure with screws.
    Tighten the locking screw of each  hook to 3/16″ (5mm) depth.

  2. Locate one attachment hook in correct orientation to the screw hole at bottom middle of the back of drawer panel, and secure with screw.
    Tighten the locking screw of the hook to 1/16″ (1mm) depth.FISHER-PAYKEL-
RB36S-Integrated-CoolDrawer-Multi-Temperature-Drawer-
fig27

  3. Attach the handle* to the drawer panel.
    Refer to the installation guide included in your purchased handle kit to attach the handle.FISHER-PAYKEL-RB36S-Integrated-CoolDrawer-Multi-
Temperature-Drawer-fig28

CUSTOM PANEL

Refer to the dimensions below for the preparation of the Custom door panel when attaching the attachment hooks. Drill the screw holes using a 6mm drill bit, and counterbore from the rear.
Refer to stainless steel panel instructions for securing the attachment hooks to the drawer panel. Refer to the installation guide included in your purchased handle kit to attach
the handle.FISHER-PAYKEL-RB36S-Integrated-CoolDrawer-Multi-Temperature-
Drawer-fig29

ATTACH POWER CORD & TRIM BRACKETS
  1. Connect the power plug to the back of the CooldrawerTM and clip the cord in place.
  2. Secure the trim brackets with screws to the side of the CooldrawerTM in the correct orientation.

POSITION PRODUCT INTO CABINETRY

  1. Place the CooldrawerTM in front of the cabinetry and connect the power plug to the power outlet.FISHER-PAYKEL-RB36S-Integrated-CoolDrawer-Multi-Temperature-Drawer-fig32
  2. Slide the CooldrawerTM into the cavity.
    Do not screw in the trim brackets at this stage.

ATTACH DRAWER PANEL

  1. Hook the drawer panel onto the drawer front channel.
  2. Close the drawer and check vertical clearances.
  3. Remove the panel and adjust the top attachment hooks as necesary.FISHER-PAYKEL-RB36S-Integrated-CoolDrawer-Multi-Temperature-Drawer-fig34
  4. Replace the panel on the drawer and confirm vertical clearances.
  5. Slide the panel to achieve even horizontal clearances.
  6. Open the drawer and clamp the panel onto the drawer by tightening the bottom attachment hook.
  7. Close the drawer and ensure it is flush with the adjacent cabinetry. If not, the product may have to be pulled back or forward.
  8. Ensure there is clearance between the panel and cabinetry when the drawer is fully closed.

SECURE PRODUCT TO CABINETRY

Open the drawer and secure the product to the cabinetry by securing the four trim brackets with screws.

ATTACH SIDE TRIMS TO CABINETRY

Install the side trims to the trim brackets in the correct orientation.

ATTACH FALSE PANEL

FISHER-PAYKEL-RB36S-Integrated-CoolDrawer-Multi-
Temperature-Drawer-fig40

  1. Attach the false panel securely as recommended by the cabinet maker.
    The false panel needs to be removable for servicing.

  2. Check the top and side clearances.
    Ensure to check basic operation and complete the final checklist.

INSTALLER CHECKLIST

Read all installation guidance in this document to see if the unit has been correctly installed. Ensure that installation has been completed correctly before use.
TO BE COMPLETED BY THE INSTALLER
Ensure that:

  • Has all packaging been removed from the appliance?
  • Is the appliance securely fastened to the cabinetry?
  • Does the drawer slide freely and close properly?
  • Has the outlet duct been installed correctly?
  • Is the appliance level?
  • Are the panels securely attached?
  • Have the panels been properly aligned for correct operation and appearance? Are all clearances even?
  • Is there clearance between drawer and cabinetry frame?
  • Has the power cord been plugged into a properly earthed 3-prong outlet, which has been installed in accordance with all applicable electrical codes?
  • Is the control panel lit?
  • Can you hear the compressor motor running?
  • When a hand is placed near the toe kick, can airflow be felt under front right-hand side of appliance?
  • Have you demonstrated the basic operation to the customer?

Complete and keep for safe reference:

  • Model
  • Serial No.
  • Purchase Date
  • Purchaser
  • Dealer Address
  • Installer’s Name
  • Installer’s Signature
  • Installation Company
  • Installation Date

FISHERPAYKEL.COM
© Fisher & Paykel Appliances 2021. All rights reserved.
The models shown in this guide may not be available in all markets
and are subject to change at any time.
The product specifications in this guide apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time.
For current details about model and specification availability in your country, please go to our website or contact your local Fisher & Paykel dealer.
866529A 02.21

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Fisher & Paykel User Manuals

Related Manuals