Living Enrichment LE-203 Mini Movie Video Projector Instruction Manual

Living Enrichment LE-203 Mini Movie Video Projector

Important Safety Instructions

1. Read these Instructions.
2. Keep these Instructions.
3. Heed all Warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifier) that product heat.
9. Protect the power cord from being walked on or pinched par?cularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
10. Only use attachments/accessories specified by the manufacturer.
11. Unplug this apparatus during lightning storms or when unused for long periods of time.
12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
13. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

Additional Warnings and Precautions

1. Do not look directly into the projector light.
2. Don’t touch the project lens
3. Mains adapter is used as disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected from the mains socket outlet completely.
4. CAUTION: Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation exposure.
5. WARNING: Changes or modified to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
6. WARNING: Use of this unit near fluorescent lighting may cause interference regarding use of the remote. If the unit is displaying erratic behavior move away from any fluorescent lighting, as it may be the cause.
7. WARNING: Shock hazard – Do Not Open.
8. Caution and marking information is located at the rear or bottom of the apparatus.
9. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain, moisture, dripping, or splashing.
10. Objects filled with liquids, such as vases, shall not be placed on the apparatus.

FCC Warning

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• onsult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

In The Box

Remove & Close The Lens Cover

Placing Your Projector

Your projector can be installed in four different configurations ( see picture below):
Front Table:

• Select this location with the projector placed near the floor in front of the screen. This is the most common way to position the projector for quick setup and portability.

• Front Ceiling:
  Select this location with the projector suspended upside-down from the ceiling in front of the screen.
  NOTE: A projector mount is required to install the projector in a ceiling.

• Rear Table:
  Select this location with the projector placed near the floor behind the screen.
  NOTE: That a special rear projection screen is required.

• Rear Ceiling:
  Select this location with the projector suspended upside-down from the ceiling behind the screen.
  NOTE:
  A projector mount is required to install the projector in a ceiling.
  A special rear projection screen is required.

To Rrduce Image Distortion

It is recommended to move the projector as close to center of screen.

Distance Between The Projector And Screen
Measure the distance between the projector and where you want to position the screen. This is the projection distance.

Placing Your Projector On Ceiling
When installing the projector in the ceiling, please purchase a projector mount recommended by an installation professional and follow the instructions that come with the mount.
Before installing the projector in the ceiling, please check to make sure the ceiling structure can support the weight of the projector and the mount. If in doubt, please ask the advice from an installation professorial.
NOTE: Projector mount and screw(s) not included

Adsust The Vertical Location
Follow below picture to adjust the vertical location.

Adjust The Focus And Keystone
Follow below picture to adjust the focus and trapezoidal screen.

Adjust the focus by turning the knob while observing the image pixels near the center of the screen. Optimal focus is obtained when the pixels are clearly visible. Depending on the projected screen size, the focus near the screen edges may be less sharp than the screen center.
Keystone image is created when the projector beam is projected to the screen in an angle. Keystone correction will restore the distorted image to a rectangular or square shape.

Controls Of Remote

Install /Remove Battery of Remote

Remove the battery compartment cover on the back of your remote by carefully sliding to open. The battery cover can then be lifted away. Fit the correct batteries (2 X AAA batteries not included), referring to the polarity markings. Finally, replace the cover.

NOTES:

• Batteries shall not be exposed to excessive heat such as sunshine, fire
• Be sure that the batteries are installed polarity correctly. Only same or equivalent type batteries as recommend are to be used.
• Do not dispose of batteries in fire, battery may explode or leak. Do not try to recharge a battery
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc) batteries

Controls Of Projector

Install Power Adapter
Follow below picture to connect power adapter
Connect small end of adapter FIRST. Plug the adapter body to power outlet.

Connection

Connect HDMI Show The Image On Projector Screen

Follow below picture to connect HDMI cable and device.

1. Turn off the unit before connect HDMI cable.
2. After connect, press the button to turn on unit and power indicator will light GREEN
3. Press the / SOURCE button to HDMI mode and the video Of HDMI device will show on projector screen. There are 2 HDMI input, HDMII interface corresponds to HDMI 1 in SOURCE mode , and HDM12 interface corresponds to HDMI 2 in SOURCE mode.
4. Press the button to turn off unit power.

HDMI hd signal input : this interface can be input with HD player HDMI output at the connection.

Connect AV Show The Image On Projector Screen
Follow below picture to connect AV cable and device.

1. Turn off the unit before connect AV cable.
2. Use AV cable to connect follow below figure
3. After connect, press the button to turn on unit and power indicator will light GREEN
4. Press the / SOURCE button to AV mode and the video of AV device will show on projector screen
5. Press the button to turn off unit power.

Connect VGA Show The Image On Projector Screen
Follow below picture to connect HDMI cable and device.

1. Turn off the unit before connect VGA cable.
2. Press the button to turn off power of your projector before connection. light GREEN
3. After connect, press the button to turn on unit and power indicator will light GREEN
4. Press the / SOURCE will show on projector screen.
5. Press the button to turn off unit power.

Please refer to the following table to adjust the output signal from computer

| | |
---|---|---|---

PC

| ****

VGA

| ****

640×480

| 31.5| 60
34.7| 70
37.9| 72
37.5| 75

SVGA

| ****

800×600

| 31.4| 50
35.1| 56
37.9| 60
46.6| 70
48.1| 72
46.9| 75

XGA

| ****

1024×768

| 40.3| 50
48.4| 60
56.5| 70

Connect Audio Output

( Aux Out / Line Out / Earphones)

Follow below picture to connect audio cable and device.

1. Press the button to turn off power of your projector before connection.
2. Use audio cable to connect follow below figure.
3. After connect and turn on both units. Your projector sound from external device now.
4. After using , turn off both unit

Station Amplifier

Install USB Device And Micro Sd Card “TF”
Follow below picture to install USB and TF card
Turn off the unit before install USB / TF card.

Using TF Card And USB Playback

(Media Player)

Install / TF device:

1. Tum off the unit before install USB / TF card.
2. Install the USB device into USB port.
3. After connect, press the button to turn on unit and the power indicator light GREEN.
4. Press the SOURCE button to enter and use buttons to search the MEDIAPLAYER mode.
5. After selection, use buttons to search the MUSIC / PHOTO / MOVIE icon and press the button to enter. If necessary, use the 4/ Y button to select TF card or USB and press the press the button to enter.
6. Use buttons to search the correct file and press the button to preview playback file and press the button of unitor button of remote to Start playback.
7. Press button to fast search forward and rewind.
8. Press button to search next or previous file.
9. During playback, press the button to pause and press again to resume.
   NOTE: Remove USB / TF device, press the button to turn Off power FIRST.

Using Projector Menu 1.0

Press button to enter projector menu. Press again to previous status.

1. Picture Mode
   Select Vivid, User (custom), Soft ,or Standard

2. Contrast ,Brightness, etc
   Set Picture Mode to “User “ to adjust these settings

3. Color Temperature
   Select Warm ,Cool, or Medium.

4. Aspect Ratio
   Select 16:9, 4:3 , or Auto

5. Noise Reduction
   Select Off, Low , Middle , High or Default

6. Screen

Color temper… (temperature)

Customer define| Parameter
red| 0-100
blue| 0-100
green| 0-100
Aspect Ratio

4:3| The signal in a 4:3 aspect ratio projection image
16:9| The signal in a 16:9 aspect ratio projection image

Using Projector Menu 2.0

Press button to enter projector menu. Press again to previous status.

1. Sound Mode
   Select Music, Movie, User (custom), Sports ,or Standard

2. Treble, Bass
   Set Sound Mode to “User “ to adjust these settings

3. Balance
   Adjust the audio balance.

4. Surround Sound
   Turn Surround Sound ON or OFF

Using Projector Menu 3.0

Press button to enter projector menu. Press again to previous status.

1. OSD Language
   Select different language, Follow below figure.

2. Restore Factory Default
   Select Y or N

3. Panel Flip Rotate
   Select rotate 0, rotate 1, rotate 2, rotate 3..

4. Keystone correction
   Default by 0, adjust different angle between -22 to 22.

5. INFO
   Display the unit information as below.

Using Projector Menu 4.0

Press the button to enter the projector menu. Press again to the previous status.

1. Clock– —
   Select the clock to Day, Month, Year, Hour, and Minutes.

2. Off Timer
   Select turn off timer to Day, Hour, and Minutes.

3. On Timer
   Select turn on the timer to Day, Hour, and Minutes.

4. Sleep Timer
   Select sleep timer to Off, 10min, 20min, 30 min, 60min, 90min, 120min, 180min, 240min

5. Auto Sleep
   Select auto sleep function to Never, 4 hours, 6 hours, 8 hours.

Specifications

White light output 45 Lumens

Display Native Resolution| 800 x 480
HDMI Input Supported

Video Resolution.

| 1080p , 1080i , 720p, 576i , 480p, and 480i
Power Consumption| Operating 36W; Standby 0.8W
Power Input

Connect Included Adapter

| DC 12V , 3.5A
Included Adapter

Connect DC input of unit

| Input AC100-240V,50/60Hz

Output DC12V , 3.5 A

Display Color| 16.7K
Projection Size| 30-100 inch
Signal Port| Video / VGA / HDMI
USB Port| Support USB device up to 1TB

Support format mpeg1, Mpeg2 ,mpeg4, mp3 , Jpeg

SD Card| Support SD card up to 1TB

Support format mpeg1, Mpeg2 ,mpeg4, mp3 , Jpeg

Weight| 0.9 KG
Dimension| 203 x 150 x 82 mm

Ideal for dark viewing environments for optimal performance.

Please note: Projector brightness is measured in ANSI lumens. Your viewing environment is the deciding factor in how many lumens your projector needs.

TROUBLESHOOTING

Before resorting to the maintenance service, please kindly check yourself with the following chart.

No Image is Projected or a “No Signal” message is displayed

| 1. Power light is on. If it is not on, check the projector is plugged into the mains, that the socket is switched on, and then press the power button on the projector.

2. Check the lens cover has been removed. 3. Check the cables are securely attached and installed as per the User Manual.

4. The image source may not be set correctly. Press the Source button on the Control Panel or the Remote, to select the correct setting.

5. Check in the Menu section under the Video input signal to make sure that has been set correctly.

---|---

The Lamp (Bulb) switches off after a period of time

| Is the warning light indicator red? If so, the projector is overheating which turns the light off automatically.

1.Leave the projector to cool for a few moments. 2.Once cooled, check nothing is blocking the ventilation vents.

3. Check the air filter is clean and clean if necessary.

4. Turn on the projector.

If the issue persists please contact your support provider for further assistance.

The Image is wider at the top/bottom of the screen| This is called a keystone and is due to the projection angle not being perpendicular to the screen. To correct use the projector’s inbuilt keystone function to adjust the image.

Spots on the screen

| Using a vacuum cleaner to clean the lens. If cleaning doesn’t resolve things, please contact your support provider for further assistance.

The image brightness has faded

| This could possibly be caused by the ambient light in the room. If not, the chances are that you need to replace the lamp (bulb).

FAQ’s

What is the resolution of the Living Enrichment LE-203 projector?

The projector features a 1080P resolution, providing high-definition visuals.

Does the LE-203 projector support multimedia playback?

Yes, the LE-203 projector is designed for multimedia use, allowing you to play videos, images, and presentations.

What kind of connectivity options does the LE-203 projector offer?

The LE-203 projector likely offers various connectivity options such as HDMI, USB, VGA, and possibly wireless connections.

Is the Living Enrichment LE-203 projector suitable for home entertainment?

Yes, the LE-203 projector is suitable for home entertainment, offering high- resolution visuals for movies, gaming, and more.

What is the brightness level of the LE-203 projector?

The projector might feature a certain level of brightness measured in lumens, ensuring clear visibility in different environments.

Can I use the LE-203 projector for business presentations?

Yes, the LE-203 projector can be used for business presentations, thanks to its multimedia capabilities and high resolution.

Does the LE-203 projector have built-in speakers?

The projector may come with built-in speakers for audio playback, reducing the need for external audio devices.

Is the projector compatible with external devices like laptops and gaming consoles?

Yes, the LE-203 projector is likely compatible with various external devices like laptops, gaming consoles, and more.

What is the lamp life of the LE-203 projector?

The projector might have a certain lamp life, indicating how long the lamp is expected to last before needing replacement.

Does the LE-203 projector support keystone correction?

Yes, the projector might offer keystone correction, allowing you to adjust image distortion caused by angled projection.

Is the LE-203 projector easy to set up?

Yes, the projector is designed for easy setup, and it might come with user- friendly features for quick installation.

What accessories are included with the Living Enrichment LE-203 projector?

The projector might come with accessories such as a remote control, cables, and possibly a carrying case for convenience.

Download this PDF Link: Living Enrichment LE-203 1080P Multimedia Projector Instruction Manual

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>