FALCON RIDGE YA-RHINO-MC01 Yamaha Rhino Mini Cab Enclosure Instruction Manual
- June 3, 2024
- FALCON RIDGE
Table of Contents
FALCON RIDGE YA-RHINO-MC01 Yamaha Rhino Mini Cab Enclosure
INSTALLATION INSTRUCTION
CAUTION: Do not smoke inside the cab or expose the enclosure to direct
flames. Product is FLAMMABLE.
Be sure to read these instructions thoroughly before opening and installing
the enclosure. The installation is best done when the temperature is 70°F or
warmer. The temperature affects the adhesive Velcro. If conditions prevent
installing in warmer weather it helps to store the adhesive Velcro at room
temperature prior to installation.
- Carefully open the carton and unroll the enclosure on a large flat surface that is clean and free of dirt or other material.
- Check over the parts included in the carton with the parts list shown below:
- Velcro hook strips 2 each 3” long
- Velcro hook strips 2 each 8” long
- Velcro hook strips 8 each 10” long
- Enclosure 1 each
- Loosely drape the cab enclosure over the roll cage. Be sure to center the cab left to right and front to back and begin by placing the adhesive Velcro strips on either side of the windshield. You will be using 4 of the 8 -10” strips provided. Once you have the Velcro attached to match the Velcro tabs on the enclosure attach the windshield and move on to the rear of the cab.
- Next raise the bed and place the 2 – 12” adhesive Velcro strip across the bottom rear of the cab, one for each of the tabs along the bottom. Now pull down on the rear of the cab enclosure and affix to the Velcro.
- Attach two of the 10” adhesive strips down the side of the rear window to match up with the Velcro tab sewn to the cab.
- Next move back to the front of the cab and use the two webbing straps to attach to the bumper or a convenient location that will reach. Pull it down and around a secure location and back up and lace it through the ladder lock by entering it from the back and feeding it back through itself and then pull tight.
- Lastly you will need to check the location for the two remaining 10” Velcro strips that go along the bottom edge of the windshield. You may need to mark the location and then loosen the nose to attach the adhesive strips to the hood and then tighten the nose and press the two parts of the Velcro together.
Cleaning and Storage Recommendations:
- Before removing the enclosure for storage, make sure it is clean and dry, to prevent soiling the textile and scratching the clear vinyl windows. Clean with a soft rag or sponge using a mild liquid detergent soap and warm water solution. Let the enclosure dry thoroughly before attempting to roll for storage.
- It is important that the enclosure be rolled up for storage rather than folding. Folding will cause undesirable creasing of both the enclosure textile and the clear vinyl windows. Carefully roll up the enclosure similar to the way it was when it was packed at the factory. Put the rolled enclosure back into the carton for storage at normal room temperature. It is best not to expose the enclosure to either extreme hot or cold temperatures when storing.
- A special cleaner/conditioner is available from Falcon Ridge that will greatly increase the service life of the cab enclosure. If needed, additional hook and loop sets are available, as well as other spare parts and hardware. Contact Falcon Ridge for information.
- Transporting or trailering your UTV with the enclosure installed is not generally recommended. It is best to remove the enclosure before transporting your UTV.
Return Policy
If for any reason you choose to return this product it must be returned within
30 days from date item is received. You MUST package the product exactly as it
was originally packaged from the factory to get a full refund for the product!
The vinyl windows should never be folded when packaging in the box or for
storage purposes. Lay all the windows on top of each other with the canvas
folded in between and the paper (if available) on both sides of the windows.
All returned products will be inspected upon arrival at the production
facility and must be in unused, factory new condition to receive refund – a
25% restocking fee will apply. If ordered from Falcon Ridge please call at
606-845-7439 to gain a return
authorization number, use our preferred shipping carrier (UPS) to return the
item (unless the item is defective, you are responsible for paying the
shipping to return the item.) Any returns submitted to Falcon Ridge without a
return authorization number will be charged a 20% restocking fee. If ordered
from one of Falcon Ridge’s many distributors, you must first call them and see
what their return policy is. Once your item reaches our production facility,
our customer satisfaction team will inspect your item to ensure unused,
factory new condition. NOTE: All windshields must be returned with the
original protective film intact and not removed. Do NOT REMOVE if you have any
intentions of returning the item. Refund/ replacement of a windshield will
only be processed on items with original protective film or if the windshield
is defective.
Items must be properly packaged in the original shipping carton to protect
them during transit and ensure your returned item arrives back factory fresh,
and in new resalable condition (any returned items that have been used,
altered or damaged in any way will not be subject for a refund.) All contents
including instruction manuals, accessories, hardware, Velcro, etc. must be
included in your return shipment. Only items in OEM factory new condition will
be approved. Once returned items are received, credit will be issued to the
original credit card/ payment method used for the purchase. Outbound shipping
and return shipping cost will not be refunded. Please allow 4 to 6 weeks for
your refund to be processed.
Warranty
To The Owner of this Product:
Thank you for purchasing one of our Falcon Ridge Cab Enclosures, Tops &/or
Windshields! Below are the terms under which your product is covered under our
manufacturer’s warranty. 30 Day Warranty which includes and is not limited to
replacing the enclosure, tops and/or windshield due to defects of the product.
Please refer to the return policy in this case for more information.
1 Year Warranty includes any defect in material or workmanship within this
time frame we will gladly correct the problem or replace the enclosure, tops
&/or windshield. Upon submitting for the correction or replacement we will
need to receive pictures of the defect in material or workmanship along with
the receipt from the date of purchase.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>