AMPTDBU RF Controller User Manual

AMPTDBU RF Controller User Manual

Declarations

U.S. Radio Frequency FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

ISED RSS Warning:

This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.

Fields of Application

• Cellular/Honeycomb Standard
• Cellular/Honeycomb Skylight
• Cellular/Honeycomb TDBU
• Cellular/Honeycomb Day/Night

Specifications

Working temperature: -10º C ~ +50º C
Input Voltage: USB 5V 1A / USB 5V 2A
Radio Frequency: 433.92 MHz
Maximum Running Time: 6 minutes

Attention

Never drop, knock, drill or submerge the motor.

Read all safety instructions before installation.

Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty

Safety Instructions

1. Do not expose motor to humid, damp, or extreme temperature conditions.
2. Do not drill into motor.
3. Do not cut the antenna. Keep it clear from metal objects.
4. Do not allow children to play with this device.
5. If the power cable or connector is damaged, do not use.
6. Ensure the correct crown and drive adaptor are used.
7. Ensure the power cable and aerial is clear and protected from moving parts.
8. Cable routed through walls should be properly isolated.
9. Motor is to be mounted in horizontal position only.
10. Before installation, remove unnecessary cords and disable equipment not needed for powered operation.
11. Installation and programming should be performed by a qualified professional. Use or modification outside the scope of these instructions may void warranty

Do not dispose of in general waste.
Please recycle batteries and damaged electrical products appropriately

Please scan QR code to see more AMP™ product information

System Overview

Switch Functions

1. When the Switch is at Location 1, it is Cellular/Honeycomb TDBU and Cellular/Honeycomb Day/Night Shades working mode.
2. When the Switch move to Location ON, it is Cellular/Honeycomb Standard and Cellular/Honeycomb Skylight working mode.
3. The Factory default mode is setting at Location 1.

P1 Button Instructions

1. Test Motor (Wakes and Runs)
   Happening as you press for 1 second

2. Activate Pairing Mode
   Happening as you press for 2 second

3. Sleep Mode
   Happening as you press for 6 seconds

4. Reverse Motor 1 with Motor 2
   Happening as you press for 10 seconds

5. Reset To Factory Settings
   Happening as you press for 14 seconds

Button Instructions

Rechargeable Battery

• Blinking red:
  Low battery alert

• Blinking green:
  Charging in process

• Solid green:
  Battery has finished charging

Essential Settings

The steps in factory mode must be completed to ensure proper operation.

Pair / Unpair Remote Control

• a. Press “P1” button (about 2 sec) on the End Cap as shown until motor jog x1.

• b. In the next 10 secs, press and hold Left “Stop” button on the remote control until motor jog x2.

• Repeat the same procedure to unpair remote contro

Change Motor Direction (if necessary)

Press Left “Up” or Left “Down” button to check if the shade moves in the desired direction.

If you need to reverse the direction, press and hold (about 2 sec) Left “Up” and “Down” button

*The operation is only valid when there are no limits.

Setting the Upper and Lower Limits

Set Upper Limit

a. Press Right “Up” button to raise the Middle Rail, then press Right “Stop” button when it is in the desired upper limit.

b. Press Left “Up” button to raise the Bottom Rail, then press Left “Stop” button when it is in the desired upper limit.

c. Press and hold (about 2 sec) Left “Up” and Left “Stop” buttons simultaneously until motor jog x2.

Set Lower Limit

a. Press Left “Down” button to lower the Bottom Rail, then press Left “Stop” button when it is in the desired lower limit.

b. Press Right “Down” button to lower the Middle Rail, then press Right “Stop” button when it is in the desired lower limit.

c. Press and hold (about 2 sec) Left “Down” and Left “Stop” buttons simultaneously until motor jog x2.

Adjust Limits

Adjust the Upper Limit

a. Press and hold (about 5 sec) Left “Up” and Left “Stop” buttons simultaneously until motor jog x1.

b. Press Right “Up” button to raise the Middle Rail, then press Right “Stop” button when it is in the new desired upper limit.

c. Press Left “Up” button to raise the Bottom Rail, then press Left “Stop” button when it is in the new desired upper limit.

d. Press and hold (about 2 sec) Left “Up” and Left “Stop” buttons simultaneously until motor jog x2.

Adjust the Lower Limit

a. Press and hold (about 5 sec) Left “Down” and Left “Stop” buttons simultaneously until motor jog x1.

b. Use Left “Down” button to lower the Bottom Rail then press Left “Stop” button when it is in the new desired lower limit.

c. Press Right “Down” button to lower the Middle Rail, then press Right “Stop” button when it is in the new desired lower limit.

d. Press and hold (about 2 sec) Left “Down” and Left “Stop buttons simultaneously until motor jog x2.

Favorite Position

Set Favorite Position

a. Use Left “Up” or Left “Down” button to move the shade to desired Favorite position.

b. Press Right “P2” button on the back of remote control until motor jog x1.
c. Press and hold Left “Stop” button until motor jog x1.

d. Once more, press and hold (about 2 sec) Left “Stop” button until motor jog x2.

Send Shade to Favorite Position

Press and hold (about 2 sec) Left “Stop” button, motor will move to Favorite position.

Delete Favorite Position

a. Press Right “P2” button until motor jog.

b. Press and hold Left “Stop” button until motor jog.
c. Once more, press and hold Left “Stop” button until motor jog x1.

Roller Mode and Sheer Mode

Roller Shade Mode – continue movement after a short press – Default Mode

a. Press and hold (about 5 sec) Left “Up” and Left “Down” buttons simultaneously until motor jog x1.

b. Press and hold (about 2 sec) Left “Stop” button until motor jog x2.

Sheer Shade Mode – jog movement after a short press (continue movement after a long press)

a. Press and hold (about 5 sec) Left “Up” and Left “Down” buttons simultaneously until motor jog x1.

b. Press and hold (about 2 sec) Left “Stop” button until motor jog x1.

Add or Remove Additional Remote

Using Current Remote Control

a. On the current remote control, press Right “P2” button until motor jog x1.

b. Once more, on the current remote control, press Right “P2” button until motor jog x1.
c. On the New remote control, press Right “P2” button until motor jog x2.

Adjust Motor Speed

Acceleration Speed

a. Press Right “P2” button until motor jog x1.

b. Press Left “Up” button until motor jog x1.
c. Once more, press Left “Up” button until motor jog x2.

Decelaration Speed
a. Press Right “P2” button until motor jog x1.

b. Press Left “Down” button until motor jog x1.
c. Once more, press Left “Down” button until motor jog x2.

 Do not dispose of in general waste. Please recycle batteries and damaged electrical products appropriately.

 Please scan QR code to see more AMP™ product information

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>