TESmart HKS1601A10 HDMI KVM Switch 16 port 4K USB Hub User Manual

TESmart HKS1601A10 HDMI KVM Switch 16 port 4K USB Hub

Features

• Using only 1 set of keyboard, mouse and monitor to control 8/16 host devices
• Support Unix/Windows/Debian/Ubuntu/Fedora /Mac OS
• X/Raspbian/Ubuntu for Raspberry Pi and other Linux based system
• With EDID emulators in every input ports, keep PCs always have correct display information
• Support hot plug, connect or disconnect devices to the HDMI switch in any time and without turn off devices
• Support auto switching to monitor computers in a specified time interval
• Support front panel buttons, IR signals, keyboard hot keys, RS232 serial commands or IP commands to control KVM switch
• Support resolution up to 3840*2160@30Hz
• Auto input detect and switch
• With extra standard USB 2.0 hub port, it is possible to connect bar code scanner, USB hard drive or other USB devices to KVM just as you have plug these devices directly to computer.
• Support DVI-D single link sources and displays with the use of HDMl-to-DVI adapters

Packing List

• 1 * HDMI KVM Switch
• 1 * DC 12V Power Adapter
• 1 * IR Remote Control
• 1 * IR Receiver Cable
• 1 3 Pins Connector (For RS232) 2 Rack-ears
• 1 * User’s manual

Bx1 (A30) Panel Description:

IR In

| Connect IR receiver extension cable to this port, then it is able to use IR control even the KVM switch is installed in a rack
2| DC 12V| 12V DC power supply
__

__

3

| __

RS232 port

| Connect this port to any control termination, then it is able to select the input sources by sending RS232 commands
__

4

| __

USB 2.0 port

| For USB 2.0 devices, for example printers, USB hard disk, barcode scanner, touch pad etc
5| HDMI output| Connect to HDMI display
__

6

| USB keyboard and mouse input| For USB keyboard and mouse input, including wireless keyboard and mouse
7| HDMI input ports| Connect to HDMI sources devices
ID| Name| Description
---|---|---
__

8

| USB data| Connect to computer’s USB ports by USB type A to type B cable
__

__

__

9

| __

__

Auto scan time interval settings

| [MIN]: Press button [MIN] to loop between 0-59 minutes

[SEC]: Press button [SEC] to loop between 0-59 seconds

[Set] : After setting minutes and seconds, press button [Set] to enter final scan time interval setting

__

10

| __

Status LED

| Red : Normal status

Green : Auto scanning mode

11| IR receiver| Receive IR signal
__

12

| __

LED display

| Display current selected input source number
__

__

__

__

13

| __

__

__

__

Keypad

| [1-8]: Press these buttons to directly select input 1-8 sources.

[Close]: Press this button directly will turn on or turn off the HDMI output display

[Scan]: Press this button to start or stop automatically scan between input 1 to input 8. The interval time can be set by button [Set], [MIN], [SEC] as described bove

15| Power switch| Turn on or off the power supply

8×1(A30) Connection Diagram:

Note,

1. HDMI Cable
2. USB type A to type B cable

16×1(A 10) Panel Description

IR In

| Connect IR receiver extension cable to this port, then it is able to use IR control even the KVM switch is installed in a rack
2| DC 12V| 12V DC power supply

3

| ****

RS232 port

| Connect this port to any control termination, then it is able to select the input sources by sending RS232 commands

4

| USB keyboard and mouse input| For USB keyboard and mouse input, including wireless keyboard and mouse
5| HDMI output| Connect to HDMI display

6

| ****

USB 2.0 port

| For USB 2.0 devices, for example printers, USB hard disk, barcode scanner, touch pad etc
7| HDMI input ports| Connect to HDMI sources devices
ID| Name| Description
---|---|---

8

| USB data| Connect to computer’s USB ports by USB type A to type B cable

9

| ****

Auto scan time interval settings

| [MIN]: Press button [MIN] to loop between 0-59 minutes

[SEC]: Press button [SEC] to loop between 0-59 seconds

(Set] : After setting minutes and seconds, press button [Set] to enter final scan time interval setting

10

| ****

Status LED

| Red: Normal status

Green: Auto scanning mode

11| IR receiver| Receive IR signal

12

| ****

LED display

| Display current selected input source number

13

| ****

Keypad

| (1-9]: Press these buttons to directly select input 1-9 sources.

(0/Close]: Press this button directly will turn on or turn off the HDMI output display; Press [1+] then (0/Close] to select input 10

[1+]: Press [1+] then [1]-(6] to select

input 11-16

[Scan]: Press this button to start or stop automatically scan between input 1 to input 8. The interval time can be set by button [Set], [MIN], [SEC] as described above

15| Power switch| Turn on or off the power supply

Note:

1. HDMI cable
2. USB typeAtotypeBcable.

Basic Operation

Port selection

Use front panel keypad

• 8×1(A30): Directly press button [1]-18] to select input ports 1-8
• 16×1(A10): Directly press button [1]-[9] to select input ports 1-9, press [OUT] then [0/Close]. [11-[6] to select input ports 10-16.

1.2 Use IR remote control

• 8×1(A30): Directly press [1]-[8] button on the IR remote control to select input port 1~8;
• 16×1(A10): Directly press [11-[16] button on the IR remote control to select input port 1-16.

Use keyboard hot keys

• 8×1(A30): Press keyboard [Scroll lock] key twice, then press I1-18] within 2 seconds to directly select input ports 1~8;
• 16×1(A10): Press the keyboard [Scroll lock] key twice, then press [1] and wait around 2 seconds to select input 1,
• 16×1(A10): Press the keyboard [Scroll lock] key twice, then press [2-I9] within 2 seconds to directly select input ports 2-9;
• 16×1(A10): Press the keyboard [Scroll lock] key twice, then press [1] then press [0]-[6] within 2 seconds to select input ports 10~16.
• 8×1(A30)8 &16×1(A10): Press the keyboard [Scroll lock] key twice, then press [Page Up]/ [Page Down] to select the previous or next port.

Turn on/off auto input detection and switch

• Press button [M] on remote control to turn on/off the auto input detection.

Auto input detection and switch mode on:

• When plug new HDMI input source to the KVM switch or power on the HDMI input source, the KVM switch will automatically select the input port that is connected to this input source.
• When unplug or power off the H DM I input source, the KVM switch will switch to the input port which is last plug in or last powered on H DM I input source.

Auto input detection and switch mode off:

• When plug new HDMI input source to the KVM switch or power on the HDMI input source, the KVM switch would not do anything, also not when unplug or power off H DM I input source.3. Mute/ unmute buzzer

Rremote control

• Press button [5] on remote control to mute or unmute buzzer.

Keyboard hot keys

• Press keyboard [Scroll lock] key two times then [F11] to mute or unmute buzzer.

Turn on/off auto scan mode

Front panel key pad

• Press [Scan] button to start auto scanning, then the KVM will automatically loop among all the powered on input sources with a specified time interval, press
  [Scan] again to stop scanning.

IR remote control

• Press [P] button to start auto scanning, then the KVM will automatically loop among all the powered on input sources with a specified time interval, press [Pl again to stop scanning.

Keyboard hot keys

• Press keyboard [Scroll lock] key two times then press  [Space] key within 2 seconds to start auto scanning, the KVM will automatically loop among all the powered on input sources with a specified time interval, press [Esc] key to stop scanning.

Setup time interval of auto scan mode

• Press front panel button [MI NJ to loop between 0-59 minutes.
• Press front panel button [SEC] to loop between 0-59 seconds.
• After setting minutes and seconds, press button [Set] to enter final scan time interval setting.

The use of mouse gesture switching

• Press keyboard [Scroll lock] key two times then press [F12] key within 2 seconds to turn on or turn off mouse gesture switching.
• When mouse gesture switching mode is on, move mouse pointer to hit left or right bound of the screen within 1 second, the KVM will switch to previous or next input source.

Use of RS232 and LAN port:

• The RS232 and LAN ports are used for selecting input source only, could not transfer keyboard and mouse data or even the video and audio, this is a redundant design for some special application when you want to switch the input sources by a termination control devices. Normally you could switch the input source by front panel keypad, IR remote control or keyboard hot keys.

For the software application packages or the API document for the RS232 and LAN port please contact with our sales. (Only for windows system)

1. Connect RS232 port
   • Follow below diagram to connect the standard 9 pin RS232 port to the 3 pins connector which is included in package, then plug the connector to the KVM ‘l”XRX· port.
2. Connect LAN port
   • Follow below diagram to connect the LAN port to local area network router or directly to PC with CatSe/6 UTP cable.

• Connect to local area network router or directly to PC

Warranty Information

• We warrant this product as free of defects in material and workmanship for a period of one (1) year from the date of shipment.
• If during the period of warranty this product proves defective under normal use, we will repair or replace this product, provided that this product has not been subjected to mechanical, electrical, or other abuse or modifications. If it fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair. Such repairs are warranted for six (6) months from the day of reshipment to the buyer.
• 31.00.0043-V004

Documents / Resources

| TESmart HKS1601A10 HDMI KVM Switch 16 port 4K USB Hub [pdf] User Manual
HKS1601A10 HDMI KVM Switch 16 port 4K USB Hub, HKS1601A10, HDMI KVM Switch 16 port 4K USB Hub, 16 port 4K USB Hub, 4K USB Hub, USB Hub
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>