CO-Z V20230329 Barber Chair User Manual

: June 14, 2024
: CO-Z

Table of Contents

CO-Z V20230329 Barber Chair
Product Information
Product Usage Instructions
Safety Information
Product Diagram
Package List
Specifications
Assembly
Adjustment
Maintenance
Contact Us
Documents / Resources

CO-Z V20230329 Barber Chair

CO-Z-V20230329-Barber-Chair-PRODUCT

Product Information

Product Name	Barber Chair
Model Number	V20230329
Material	PVC Leather, High-Density Wood Board, Polyurethane Foam,

Electroplated Steel, Cast Iron
Weight Capacity| 440 lb. (200 kg)
Net Weight| 48.5 lb. (22 kg)

Product Usage Instructions

Unpack all the components from the package.
Assemble the chair by following the steps below:
- Attach the backrest to the seat using the provided screws.
- Attach the armrests to the sides of the seat.
- Attach the footrest to the base of the chair.
Flip the seat over and slide its central hole around the shaft of the hydraulic pump.
Press down on both armrests firmly but carefully until the seat is secure.
To adjust the height of the chair:
- To raise the chair, press the pedal lightly, quickly, and repeatedly until your desired height is reached.
- To lower the chair, hold the pedal while someone is sitting in it or while pushing down on it.
Maintain the chair by following the care instructions provided in the user manual.

If you have any questions or require further assistance, please contact us at help@cs-supportpro.com. We are dedicated to resolving your issues as soon as possible.
For a PDF copy of the latest version of these instructions, use the appropriate app on your smartphone to scan the QR code provided.
Note: This user manual is applicable to model HBC-LK52-BK (Revision 29, March 2023).
Read Carefully Before Use Keep for Future Reference

Safety Information

Warning!

ALWAYS ensure all fasteners and components are intact and securely tightened before each use.
DO NOT use this chair if it is damaged or malfunctions. Repair or replace worn or broken parts before further use.
DO NOT load this chair with more than 440 pounds (200 kg).
DO NOT leave children or persons with compromised physical or mental capabilities using this chair without close supervision.
Store this product out of the reach of children after use.

Product Diagram

CO-Z-V20230329-Barber-Chair-FIG-1

Package List

Seat with 2 M5×20 Bolts × 1
Backrest with 4 M5×25 bolts × 1
Footrest × 1
Hydraulic Pump × 1
Pedal with 2 M4×8 Screws × 1
Base × 1
M5×20 Bolts × 6 Caps × 8
M5 Hex Wrench × 1
M4 Hex Wrench × 1

Specifications

Material| PVC Leather, High-Density Wood Board, Polyurethane Foam, Electroplated Steel, Cast Iron
---|---
Dimensions| Height Range| 33.1–37 in.| 84–94 cm
Backrest| 18.9×14.5×2.8 in| 48×37×7 cm
Seat| 19.7×19.7 in.| 50×50 cm
Seat Elevation| 41–51 cm| 16–20 in
Armrest| 2.5 in.| 6.4 cm
Weight Capacity| 440 lb.| 200 kg
Net Weight| 48.5 lb.| 22 kg

Assembly

Place the hydraulic pump onto the base, aligning its bottom holes with those of the base.
- Secure the pump using six M5×20 bolts and tighten them with the M5 hex wrench. Place the base right side up on a firm-level surface.
Remove the two M4×8 screws preinstalled on the pedal using the M4 hex wrench. Fit the pedal onto the pump as shown below and secure it by reinstalling and tightening the screws.
Remove the four M5×25 bolts preinstalled on the left and right sides of the backrest using the M5 hex wrench. Place the backrest between the armrests, aligning their bolt holes. Secure the backrest by reinstalling and tightening all bolts through the washers. Attach the provided caps to the bolts and press them into place.
Flip the seat over. Remove the two preinstalled M5×20 bolts using the M5 hex wrench.
- Hold the footrest against the seat so the bolt holes are aligned. Fix the footrest in place by reinstalling and tightening both bolts through the washers.
Flip the seat over and slide its central hole around the shaft of the hydraulic pump. Press down on both armrests firmly but carefully until the seat is secure.

Adjustment

To raise the chair, press the pedal lightly, quickly, and repeatedly until your desired height is reached.
To lower the chair, hold the pedal while someone is sitting in it or while pushing down on it.

Maintenance

The exterior of this chair should be cleaned periodically with a soft damp cloth. DO NOT use abrasive cleaners or caustic chemicals.
Check the parts for any looseness, wear, or damage periodically. Tighten, repair, or replace any problematic parts before further use.
If this chair will not be used for a long period of time, store it in a cool, dry, and safe place.

Contact Us

Thank you for choosing our products! If you have any questions or comments, contact us at help@cs-supportpro.com and we’ll resolve your issue ASAP!
For a .pdf copy of the latest version of these instructions, use the appropriate app on your smartphone to scan the QR code to the right.
HBC-LK52-BK Rev. 29 Mar. 2023