TESmart HKS0801A30 HDMI KVM Switch 2 Port Dual Monitor Extended Display User Manual
- June 4, 2024
- TESmart
Table of Contents
TESmart HKS0801A30 HDMI KVM Switch 2 Port Dual Monitor Extended Display
User Manual
Feature
- Using only 1 set of keyboard, mouse and monitor to control 16 host devices
- Support Unix/Windows/Debian/Ubuntu/Fedora /Mac OS X/Raspbian/Ubuntu for Raspberry Pi and other Linux based system
- With EDID emulators in every input ports, keep PCs always have correct display information
- Support hot plug, connect or disconnect devices to the HDMI switch in any time and without turn off devices
- Support auto switching to monitor computers in a specified time interval
- Support front panel buttons, IR signals, keyboard hot keys, RS232 serial commands or IP commands to control KVM switch
- Support resolution up to 3840*2160@30Hz
- Auto input detect and switch
- With extra standard USB 2.0 hub port, it is possible to connect bar code scanner, USB hard drive or other USB devices to KVM just as you have plug these devices directly to computer.
- Support DVI-D single link sources and displays with the use of HDMI-to-DVI adapters.
Package List
- 1 * HDMI KVM Switch
- 1 * DC 12V Power Adapter
- 1 * IR Remote Control
- 1 * IR Receiver Cable
- 1 * 3 Pins Connector (For RS232)
- 2 * Rack-ears
- 1 * User’s manual
16×1 (A10) Panel Description
| Name | Description | |
|---|---|---|
| __ IR In | Connect IR receiver extension cable to this port, then it is able |
to use IR control even the KVM switch is installed in a rack
2| DC 12V| 12V DC power supply
3| RS232 port| Connect this port to any control termination, then it is able
to select the input sources by sending RS232 commands
__| US B keyboard and mouse input| For US B keyboard and mouse input,
including wireless keyboard and mouse
5| HDMI output| Connect to HDMI display
6
| __ US B 2.0 port| For US B 2.0 devices, for example printers, US B hard
disk, barcode scanner, touch pad etc
7| HDMI input ports| Connect to HDMI sources devices
ID| Na me| Description
g| U SB data| Connect to computer’s US B ports by USB type A to type B cabI e
|
Auto scan time interva I set tings
| [M I N]: Press button [MIN] to loop between 0 59 minutes
[S E C]: Press button [S E C] to loop between 0 59 seconds
[Set]: After setting minutes and seconds, press button [Set] to enter final
scan time interv al setting
10| Status LE D| Red: Normal status
Green: Auto scanning mode
11| IR rece iver| Receive IR signal
2| LE D display| Display current selected inpu t source number
13
|
Keypad
| [1-9]: Press these buttons to directly select input 1-9 sources. [0/Close]:
Press this bu tton directly will turn on or turn off the HDM I output display;
Press [1+] then [0/Close] to select input 1 0
[1 +]: Press [1+] then [1]-[6] to select
input 11 16
[Scan] : Press this button to start or stop autom atically scan between input
1 to input 8. The interva I time can be set by
button [Set], [MIN], [SEC] as described above
15| Power switch| Turn on or off the power supply
16×1 (A101) Connection Diagram
Note:
- HDMI cable
- USB type A to type B cable.
Basic Operation
Port selection
Use front panel keypad
8×1(A30): Directly press button [1]-[8] to select input ports 1-8
16×1(A10): Directly press button [1]-[9] to select input ports 1-9, press
[OUT] then [0/Close], [1]-[6] to select input ports 10-16.
Use IR remote control
8×1(A30): Directly press [1]-[8] button on the IR remote control to
select input port
16×1(A10): Directly press [1]-[16] button on the IR remote control to
select input port 1-16.
Use keyboard hot keys
8×1(A30): Press keyboard [Scroll lock] key twice, then press [1]-[8]
within 2 seconds to directly select input ports
16×1(A10): Press keyboard [Scroll lock] key twice, then press [1] and
wait around 2 seconds to select input 16×1(A10): Press keyboard [Scroll
lock] key twice, then press [2]-[9] within 2 seconds to directly select input
ports
16×1(A10): Press keyboard [Scroll lock] key twice, then press [1] then
press [0]-[6] within 2 seconds to select input ports 10-16. 8×1(A30)
&16×1(A10): Press keyboard [Scroll lock] key twice, then press [Page Up] /
[Page Down] to select previous or next port.
Turn on/off auto input detection and switch
Press button [M] on remote control to turn on/off the auto input detection.
Auto input detection and switch mode on:
When plug new HDMI input source to the KVM switch or power on the HDMI input
source, the KVM switch will automatically select the input port that is
connected to this input source.
When unplug or power off the HDMI input source, the KVM switch will switch to
the input port which is last plug in or last powered on HDMI input source.
Auto input detection and switch mode off:
When plug new HDMI input source to the KVM switch or power on the HDMI input
source, the KVM switch would not do anything, also not when unplug or power
off HDMI input source.3. Mute/ unmute buzzer.
IR remote control
Press button [ ] on remote control to mute or mute buzzer.
Keyboard hot keys
Press keyboard [Scroll lock] key two times then [F11] to mute or unmute buzzer.
Turn on/off auto scan mode
Front panel key pad
Press [Scan] button to start auto scanning, then the KVM will automatically
loop among all the powered on
input sources with a specified time interval, press [Scan] again to stop
scanning.
IR remote control
Press [P] button to start auto scanning, then the KVM will automatically loop among all the powered on input sources with a specified time interval, press [P] again to stop scanning.
Keyboard hot keys
Press keyboa rd [ScrolI lock] key two times then press [Space] key within 2 seconds to start auto scanning , the KV M will automatical Iy loop among all the powered on input sources with a specified time interval, press [Esc] key to stop scanning.
Setup ti me interval of auto scan mode
Press front panel button [M IN] to loop between 0-59 minutes.
Press front panel button [SEC] to loop between 0-59 seconds.
After setting minutes and seconds, press button [Set] to enter final scan time
interval setting.
The use of mouse gesture switching
Press keyboard [Scroll lock] key two times then press [F12] key within 2
seconds to turn on or turn off mouse gesture switching.
When mouse gesture switching mode is on, move mouse pointer to hit left or
right bound of the screen within 1 second, the KVM will switch to previous or
next input source.
The RS232 and LAN ports are used for selecting input source only, could not transfer keyboard and mouse data or even the video and audio, this is a redundant design for some special application when you want to switch the input sources by a termination control devices. Normally you could switch the input source by front panel keypad, IR remote control or keyboard hot keys.
For the software application packages or the A P I document for the RS232 and LAN port please contact with our sales. (Only for windows system)
Connect RS232 port
Follow below diag ram to connect the standard 9 pin RS232 port to the 3 pins
connector which is included in package, then plug the connector to the Kv M
Tx= port.
Connect LAN port
Follow below diagram to conn ect the LAN po rt to local are network router or
directly to PC with Cat5e/6 UTP cable.
Connect to local area network router or directly to P C
Warranty Information
We warrant this product as free of defects in material and workmanship for a period of one (1) year from the date of shipment. If during the period of warranty this product proves defective under normal use, we will repair or replace this product, provided that this product has not been subjected to mechanical, electrical, or other abuse or modifications. If it fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair. Such repairs are warranted for six (6) months from the day of reshipment to the buyer.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>