TESmart HKV0402A1U VGA.HDMI Dual Monitor KVM User Manual
- June 4, 2024
- TESmart
Table of Contents
Dual Monitor KVM
User Manual
ENJOY THE VIVID WORLD
VGA • HDMI
Features :
- Using only 1 set of keyboard, mouse, and 2 monitors to control 2 computers
- Support Unix/Windows/Debian/Ubuntu/Fedora/Mac OS X/Raspbian/Ubuntu for Raspberry Pi and other Linux basic system
- Support resolution up to 3840`2160©60HZ
- Support hot plug, disconnect or connect devices to the KVM at any time without turning off the PC
- With EDID emulators in each input port, keep PCs always have the correct information, prevent display setting change while switching input ports
- Support keyboard hotkeys, IR remote control, and front panel button to control KVM
- Available to use keyboard and mouse without any delay after switching input sources
- With an extra USB 2.0 port, it is possible to connect a bar code scanner, USB hard drive, or another USB device
- Support keyboard and mouse pass-through mode to improve KVM compatibility
Packing List:
14X2 Dual Monitor KVM,
1DC 5V adapter,
1IR remote control,
1User manual
Panel View
| ID | Name | Description |
|---|---|---|
| 1 | L/R audio output | Analog audio output, connect to speakers |
| 2 | Microphone input | Connect with a microphone and receive an audio signal |
| 3 | USB connection status | LEDs will be lit if the USB TypeB ports connect to |
computers, and computers are on
4| Input selection status| Indicate the current active selected input source
LED 1 on Both monitors display PC 1
LED 2 on Both monitors display PC 2
5| Input selection button| Select input source
ID| Name| Description
---|---|---
6| IR receiver| Receive IR remote signal
7| Power switch| Turn on or turn off the power supply
8| DC 5V| DC 5V power supply
9| HDMI output ports| Connect to HDMI displays
10| Keyboard and mouse input| Connect to keyboard and mouse
11| Standard USB 2.0 port| Connect to USB 2.0 devices, printers, USB drives
12| PC 2 Input| HDMI: Connect to HDMI output of PC2
VGA: Connect to VGA output of PC2
USB: Connect to USB of the PC2(with Type A to Type B cable)
13| PC 1 Input| HDMI: Connect to HDMI output of PC1
VGA: Connect to VGA output of PC1
USB: Connect to USB of the PC1(with Type A to Type B cable)
Connection Diagram :
Note: Both HDMI and VGA cables should
be connected to the PC, if only connect HDMI or VGA cable, then the dual
monitor function would not work properly.
How To Use :
- Set up the connection according to the connection diagram.
- After all the PCs are started in step 1, then you can control the Dual Monitor KVM by keyboard hotkeys, IR control or the front-panel key ‘SW’, the specific control methods are as follows:
| Select input source 1
---|---
Select input source 2
Enable or disable the buzzer sound
Turn on or off the keyboard and mouse pass-through mode
Note: For the best compatibility, it is better to turn on the keyboard and mouse pass-through mode. In this mode, the keyboard and mouse are dynamically mapped to the computer, so you are able to use a special keyboard and mouse with multimedia keys or other customized keys.
How to identify whether the KVM is in keyboard and mouse pass-through
mode?
Turn on the KVM, and press [Scroll Lock] + [Scroll Lock] + [F3] , if the
buzzer beeps twice, the KVM is in the keyboard and mouse pass-through mode.
And beeping once means in keyboard and mouse emulation mode.
HOW TO CHANGE THE HOTKEYS COMBINATION:
If no [Scroll Lock] key on your keyboard or the [Scroll Lock] key is used for
other functionality, you can take the [Right-Ctrl] hotkey instead of the
[Scroll Lock] key by below two ways:
- After turning on KVM 10s, press the front panel button ‘SW’ until you hear the buzzer is beeping, then restart the KVM.
- Execute hotkey command [Scroll Lock]+[Scroll Lock]+[F1].
| Switch the control hotkey to [Right-Ctrl]
---|---
After you had done as above, the hotkey combinations would be changed to
[Right-CtrI]+[Right-CtrlHxxx].
Note: xxx refers to keyboard keys 1-4, F11, and F2 F3.
The same if you want to change the hotkey from [Right-Ctrl] to [Scroll Lock],
you could do it as follows:
- After turning on KVM 10s, press the front panel button ‘SW’ until you hear the buzzer beeping, then restart the KVM.
- Execute hotkey command: [Right-Ctrl]+[Right-Ctrl]+[F1].
| Switch the control hotkey to [Scroll Lock]
---|---
IR Remote Control :
Note
- For the safety request by some express companies, the remote control is not equipped battery by default. Please install the button battery CR2025 before using it.
- The unspecified buttons at above are non-functional.
Warranty Information :
We warrant this product as free of defects in material and workmanship for a period of one (1) year from the date of shipment. If during the period of warranty this product proves defective under normal use, we will repair or replace this product, provided that this product has not been subjected to mechanical, electrical, or other abuse or modifications. If it fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair. Such repairs are warranted for six (6) months from the day of reshipment to the buyer.