TESmart 0745695280312 Newest HDMI KVM Switch User Manual

TESmart 0745695280312 Newest HDMI KVM Switch

Features

• Using only 1 set of keyboard, mouse and monitor to control 2 computer devices
• Support auto-switching to monitor computers in a specified time interval
• Support front panel buttons, IR signals, keyboard hotkeys and mouse gestures to control KVM to switch inputs
• Available to use keyboard and mouse without any delay after switching input sources
• Support resolution up to 3840*2160@60Hz 4:4:4
• HDCP 2.2 compliant
•  With a USB 2.0 hub port, it is possible to connect bar code scanner, USB hard drive or other USB devices to KVM
•  With EDID emulators in each input port, keep PCs always having correct display information
• Support analog L/R audio output
•  Support HDR and Dolby Vision
•  Support keyboard and mouse pass-through mode to improve mouse and keyboard compatibility

Packing List

• 1 * 2×1 HDMI KVM Switch
• 1 * DC 5V power adapter
• 1 * IR remote control
• 1 * User’s Manual

2×1 Panel Description

__

3

| USB connection status| LEDs will be lit if the USB data ports are connected to the computers’ USB port
__

4

| Input selection status| __

Indicate current selected input source

__

5

| Input selection button| __

Select input sources

__

6

| IR receiver| Receive IR remote signal

2×1 Panel Description

__

__

7

| Keyboard and mouse pass through mode status| __

LED will be lit if keyboard and mouse pass through mode is activated

8| DC5V| 5V DC power supply
9| HDMI output| Connect to HDMI display
__

10

| Standard USB

2.0 port

| Connect to USB 2.0 device , printers , USB drives , barcode scanner
__

11

| Keyboard and mouse input| For USB keyboard and mouse input , including wireless keyboard and mouse
12| HDMI input| Connect to HDMI source devices
__

13

| __

USB data ports

| Connect to PC by USB type B to type A cable

2×1 Connection Diagram

HOW TO USE

1. Setup the connection according to the connection diagram.
2. .After all the PCs are started in step 1, then you can switch to any PC by keyboard hotkeys, IR keys or the key pad on the KVM front panel. (For example, if you want to control the PC connected to HDMI Input 2 just press the “Select” button on front panel, or press digit button [2] on the remote control, or the keyboard hotkey commands described following)

HOW TO USE KEYBOARD HOTKEYS

1. Hit the [Scroll Lock] key twice within 2 seconds, the buzzer will beep once when [Scroll Lock] is pressed the second time .
2. After step 1 enter the following hot key commands within 3 seconds, the KVM will execute the corresponding commands

Note:
3,4arefor4x1 KVM.

Enable or disable buzzer sound Enable or disable fast switching mode (Mouse gesture mode)

Turn on auto-switching mode.

Note:
The KVM will automatically loop among all the powered on input sources within a specified time interval. The default auto-switching time interval is 6 seconds, you are able to change this value by following hotkey commands:

Increase or decrease auto-switching time interval.

Note:
1 second per step, the time is up to 250 seconds.

Turn off auto-switching mode.

Note:
Execute this hotkey command to exit auto-switching mode.

Turn on/off keyboard and mouse pass-through mode.

Note:
For the best compatibility, it is better to turn on the keyboard and mouse pass-through mode. In this mode, the keyboard and mouse are dynamically mapped to the computer, so you are able to use special keyboard and mouse that with multimedia keys or other customized keys.

HOW TO CHANGE THE HOTKEYS COMBINATION

If no [Scroll Lock] key on your keyboard or the [Scroll Lock] key is used for other functionality, you can take the [Right-Ctrl] hotkey instead of the [Scroll Lock] key below in two ways:

1. Press the front panel button [Select] until you hear the buzzer is beeping, then restart the KVM.
2.  Execute the hotkey command [Scroll Lock]+[Scroll Lock]+[F1], then restart the KVM

After you had done either one of the above, the hotkey combinations would be changed to: [Right-Ctrl]+[Right-Ctrl]+[xxx].
Note:
xxx refers to keyboard key PaqeUp, PaqeDown, ~ E11, E12, SPACE+/-.

The same if you want to change the hotkey from [Right-Ctrl] to [Scroll Lock], you could do as follows:

1. Press the front panel button [Select] until the buzzer is beeping, then restart the KVM.
2.  Execute hotkey command: [Right-Ctrl]+[Right-Ctrl]+[F1].

JR Remote Control

1. Switch to input port 1
2. Switch to input port 2
3. Switch to input port 3
4. Switch to input port 4

Note:
3,4 are only available for 4×1 HDMI KVM switch

Note:
 For the safety request by some express companies, the remote control is not equipped battery by default.  The unspecified buttons at above are non- functional.

Verified keyboards and mouses

Zklli

| ****

ZMS00-5

| ****

METOO

| ****

ZS

FL.SPORTS

| ****

G12

| ****

Dareu

| ****

CK535

Newmen

| ****

GX1-KEPLER

| ****

Aigo

| ****

8362

Aigo

| ****

WQ-641

| ****

AJAZZ

| ****

AK35I

LOK.al

| ****

Colourful XBOO

| ****

Acer

| ****

KB21-2X

Note:
The above list is part of the verified keyboards and
mouses list with special HID protocol

Warranty Information

We warrant this product as free of defects in material and workmanship for a period of one year from the date of shipment. If during the period of warranty this product proves defective under normal use, we will repair or replace this product, provided that this product has not been subjected to mechanical, electrical, or other abuse or modifications. If it fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair. Such repairs are warranted for six (6) months from the day of reshipment to the buyer.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>