TOOLCRAFT 2614577 LED Work Light Instruction Manual

: June 9, 2024
: Toolcraft

TOOLCRAFT 2614577 LED Work Light Instruction Manual

1 Intended use

The product is a mains powered LED work light. The product is NOT suitable for use in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.

Important: The product has an IP54 rating. It is resistant against dust and splashing from any direction. Observe the following ingress protection criteria: Do not submerge. The power cable should be connected inside a weatherproof socket box or routed in-doors via weatherproofed cable inlet rated IP54 or higher.

If you use the product for purposes other than those described, the product may be damaged. Improper use can result in short circuits, fires, electric shocks or other hazards. The product complies with the statutory national and European requirements. For safety and approval purposes, you must not rebuild and/or modify the product. Read the operating instructions carefully and store them in a safe place. Make this product available to third parties only together with the operating instructions. All company names and product names are trademarks of their respective owners. All rights reserved.

2 Delivery contents

Product
Operating instructions

3 Latest product information

Download the latest product information at www.conrad.com/downloads or scan the QR code shown. Follow the instructions on the website.

4 Description of symbols

The following symbols are on the product/appliance or are used in the text:
Read the operating instructions carefully.
⚠ The symbol warns of hazards that can lead to personal injury.
The symbol warns of dangerous voltage that can lead to personal injury by electric shock.

5 Safety instructions

⚠ Read the operating instructions carefully and especially observe the safety information. If you do not follow the safety instructions and information on proper handling, we assume no liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/guarantee.

5.1 General

The product is not a toy. Keep it out of the reach of children and pets.
Do not leave packaging material lying around carelessly. This may become dangerous playing material for children.
If you have questions which remain unanswered by this information product, contact our technical support service or other technical personnel.
Maintenance, modifications and repairs must only be completed by a technician or an authorised repair centre.

5.2 Handling

Handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.

5.3 Operating environment

Do not place the product under any mechanical stress.
Protect the appliance from extreme temperatures, strong jolts, flammable gases, steam and solvents.
Protect the product from direct sunlight.

5.4 Operation

WARNING! Do not connect the product in series.
WARNING! Do not operate the product if covered.
WARNING! Do not use the product where water accumulates.
WARNING! Only for vertical use.
WARNING! Do not operate the product if covered.
Do not operate the product in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.
Consult an expert when in doubt about the operation, safety or connection of the product.
If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. DO NOT attempt to repair the product yourself. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.

5.5 Mains cable

Do not modify or repair mains supply components including mains plugs, mains cables, and power supplies. Do not use damaged components. Risk of death by electric shock!

The mains outlet must be located near to the device and be easily accessible.
Never plug in or unplug the mains plug when your hands are wet.
Never pull the mains plug from the socket by pulling at the cable. Always pull it from the mains socket using the intended grips.
Unplug the mains plug from the mains socket if you do not use the device for an extended period of time.
Disconnect the mains plug from the mains socket in thunderstorms for reasons of safety.
Make sure that the mains cable is not squeezed, bent, damaged by sharp edges or put under mechanical stress.
Avoid excessive thermal stress on the mains cable from extreme heat or cold.
Do not modify the mains cable. Otherwise the mains cable may be damaged. A damaged mains cable can cause a deadly electric shock.
Do not touch the mains cable if it is damaged.
- First, power down the respective mains socket (e.g. via the respective circuit breaker) and then carefully pull the mains plug from the mains socket.
- Never use the product if the mains cable is damaged.
A damaged mains cable may only be replaced by the manufacturer, a workshop commissioned by the manufacturer or a similarly qualified person, so as to prevent any danger.
Ensure that cables are not pinched, kinked or damaged by sharp edges.
Always lay cables so that nobody can trip over or become entangled in them. This poses a risk of injury.

5.6 LED light

Do not look directly into the LED light!
Do not look into the beam directly or with optical instruments!

5.7 Connected devices

Also observe the safety and operating instructions of any other devices which are connected to the product.

6 Operation

Press the power button repeatedly to cycle through modes: ON (low) ON (high) OFF.

7 Cleaning

Important: Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions.
They damage the housing and can cause the product to malfunction. Do not immerse the product in water.

Disconnect the product from the power supply.
Let the product cool down to ambient temperature.
Clean the product with a dry, fibre-free cloth.

8 Disposal

This symbol must appear on any electrical and electronic equipment placed on the EU market. This symbol indicates that this device should not be disposed of as unsorted municipal waste at the end of its service life. Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose of it separately from unsorted municipal waste. Spent batteries and accumulators, which are not enclosed by the WEEE, as well as lamps that can be removed from the WEEE in a non-destructive manner, must be removed by end users from the WEEE in a non-destructive manner before it is handed over to a collection point.

Distributors of electrical and electronic equipment are legally obliged to provide free takeback of waste. Conrad provides the following return options free of charge (more details on our website):

in our Conrad offices
at the Conrad collection points
at the collection points of public waste management authorities or the collection points set up by manufacturers or distributors within the meaning of the ElektroG

End users are responsible for deleting personal data from the WEEE to be disposed of. It should be noted that different obligations about the return or recycling of WEEE may apply in countries outside of Germany.

9 Technical data

This product contains a light source of energy efficiency class E.

9.1 Power supply

Input voltage ……………………………. 220 – 240 V/AC
Input AC frequency …………………… 50/60 Hz
Mains cable type ………………………. H05RN-F 3G 1.0 mm2
Mains cable length ……………………. 2 m

9.2 Light panel

Power consumption ………………….. max. 20 W
Illuminant ………………………………… LED
Replaceable illuminant ……………… No
Colour temperature …………………… 4000 K
Brightness………………………………… Low: 1000 lm, High: 2000 lm

9.3 Environment

Operating temperature ……………… -35 to +45 °C
Storage temperature …………………. -40 to +45 °C

9.4 Protection

Ingress protection …………………….. IP54

9.5 Others

Dimensions (W x H x D) (approx.) . 77 x 224.5 x 150 mm
Weight (approx.) ………………………. 804 g

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or the capture in electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited. This publication reflects the technical status at the time of printing. Copyright by Conrad Electronic SE.

*2614577_V2_0123_dh_mh_en 9007200000336395-2 I2/O2 en 4