SUB-ZERO Classic Series Stainless Steel Bottom Freezer Installation Guide
- June 9, 2024
- SUB-ZERO
Table of Contents
Classic Series Stainless Steel Bottom Freezer
Installation Guide
Design Guide
Classic Series
Proud Installation
ICB REVISED 5/2022
Classic Series Stainless Steel Bottom Freezer
Classic Series Models
For the Classic series refrigeration, Sub-Zero designers and engineers took a
fresh look at everything, inside and out. Exterior refinements include
redesigned grilles and lower profile hinges. Inside, new technology in food
preservation makes the Classic series refrigeration nothing short of
revolutionary.
Features and specifications are subject to change at any time without notice.
Throughout this guide, dimensions may vary by ± 3 mm.
ALL REFRIGERATOR / ALL FREEZER
OVER-AND-UNDER
SIDE-BY-SIDE MODELS
Overall Dimensions
STANDARD INSTALLATION
NOTE: 89 mm finished returns will be visible and should be finished to match cabinetry. Shaded line represents profile of unit.
| OPENING WIDTH | W |
|---|---|
| 914 mm Model | 902 mm |
| 1067 mm Model | 1054 mm |
| 1219 mm Model | 1206 mm |
If two units are installed side by side, refer to page 10 for dual standard installations.
DUAL STANDARD INSTALLATION
NOTE: 89 mm finished returns will be visible and should be finished to match cabinetry. Shaded line represents profile of unit.
| DUAL OPENING WIDTH | W |
|---|
Two 914 mm Models
Models ICBCL3650R, ICBCL3650F| 1822 mm
A dual installation kit is required for this installation.
Electrical Requirements
Installation must comply with all applicable electrical codes.
International models from the factory require a 220-240 V AC, 50/60 Hz
electrical supply, fused at the correct rating for the unit. If required by
local or national codes, the power cord can be easily replaced using the power
inlet device.
The electrical supply should be easily accessible and positioned either in a
cabinet above the refrigerator, a minimum of 2200mm above the floor or in
adjacent cabinet. If freestanding then locate the power point as per the
diagram below.
ELECTRICAL REQUIREMENTS
| Electrical Supply | 220-240 V AC, 50/60 Hz |
|---|---|
| Service | 10 amp |
| Receptacle | 3-prong grounding-type (earthed) |
Classic Series. Alternative locations of power & water supply depending on
ease of access.
1. Classic Series. Water supply above fridge. Location of 6mm flexible hose.
Tape to wall and floor with pressure limiting valve next to tap.
Plumbing Requirements
Installation must comply with all applicable plumbing codes.
For Classic Series models with an automatic ice maker, a pressure limiting
valve and 5 meters of flexible 6mm pipe with fittings is included in the
refrigerator carton.
Connect the pressure limiting valve close to the water tap, checking the water
flow is in the right direction. Ensure water connection is 1/2″ BSP male
threaded outlet. Fix the 6mm water line to the wall and floor to ensure it is
not compressed when the refrigerator is pushed into the cavity.
The water tap should be easily accessible and positioned either in a cabinet
above the refrigerator, a minimum of 2200mm above the floor, or in adjacent
cabinet.
The water line must not interfere with installation of the anti-tip brackets.
A reverse osmosis system can be used provided there is constant water pressure
of 2.4–8.3 bar supplied to the unit at all times. A copper line is not
recommended for this application.
PLUMBING REQUIREMENTS
| Water Supply Line | 6.4 mm OD copper, braided stainless steel, or PEX tubing |
|---|---|
| Water Pressure | 2.4–8.3 bar |
| Excess Line for Connection | .9 m |
Classic Series. Water supply beside fridge. Location of 6mm flexible hose.
Tape to wall and floor with pressure limiting valve next to tap.
Freestanding location of power supply.
Dual Installation
If two units are installed side by side, a dual installation kit may be
required. Installations without a custom filler strip require a dual
installation kit. If a dual installation kit is not specified, a 51 mm filler
strip is recommended between the units. A custom filler strip is required when
installing two French door or side-by-side models. Dual installations without
a filler strip can only be accomplished using two units with opposite hinges.
Refer to the illustrations below.
Dual installation kits are available through an authorized Sub-Zero dealer.
Side Panel
The custom side panels must be a minimum of 610 mm deep and 13 mm thick.
Routing will be necessary for the side panel to fit flush against the side of
the unit. Refer to
the illustrations below.
When installing a Classic series unit with a custom side panel, an accessory
kit is required. Stainless steel side panels are available through an
authorized Sub-Zero dealer.
Standard Handles
Optional stainless steel tubular and pro handles are available through an
authorized Sub-Zero dealer. Refer to the chart below for standard handle
lengths.
| HANDLE LENGTH | TUBULAR | PRO |
|---|---|---|
| Full Door | 1622 mm | 1147 mm |
| Over-and-Under Door | 1124 mm | 952 mm |
| 914 mm Drawer | 770 mm | 600 mm |
| 1067 mm Drawer | 922 mm | 753 mm |
Dual standard installation (top view)
Sub-Zero International Limited Warranty
FOR RESIDENTIAL USE
These Warranty Terms and Conditions (‘Warranty’) constitute your agreement
with Sub-Zero Group Australia Pty Ltd (ACN 610 807 899) (‘Sub-Zero’) and will
apply to your service order. The benefits given by this Warranty are in
addition to all consumer guarantees and other rights and remedies prescribed
by the Australian Consumer Law and any other applicable laws.
Our products come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure
and compensation for any other reasonably foreseeable loss or damage. You are
also entitled to have the goods repaired or replaced if the goods fail to be
of acceptable quality and the failure does not amount to a major failure.
In addition to your rights and remedies under the Australian Consumer Law,
Sub-Zero provides customers with a Warranty where, if any part of a Sub-Zero
Product is found upon inspection by an authorised Sub-Zero representative or
an associated licensed technician supplied by either Sub-Zero or a relevant
approved supplier (including a Sub- Zero factory certified service) (‘Service
Representative’) to be defective in materials or workmanship, Sub-Zero will
repair or replace the part free of charge as follows:
FULL TWO YEAR WARRANTY* (Outdoor product full one year warranty)
For two years from the date of original installation, this Sub-Zero product
warranty covers all parts and labor to repair or replace, under normal
residential use, any part of the product that proves to be defective in
materials or workmanship. All service provided by Sub-Zero under the above
warranty must be performed by Sub-Zero factory certified service, unless
otherwise specified by Sub-Zero, Inc. Where the Service Representative is
unable to identify any fault in the product, Sub-Zero may require the
consumer to provide proof that the product is defective. For the avoidance of
doubt, defective products or parts become Sub-Zero’s property. Service will be
provided during normal business hours.
*FULL FIVE YEAR SEALED SYSTEM WARRANTY
For five years from the date of original installation, this Sub-Zero product
warranty covers all parts and labor to repair or replace, under normal
residential use, these parts that prove to be defective in materials or
workmanship: compressor, condenser, evaporator, drier and all connecting
tubing. All service provided by Sub-Zero under the above warranty must be
performed by Sub-Zero factory certified service, unless otherwise specified by
Sub-Zero, Inc. Where the Service Representative is unable to identify any
fault in the product, Sub-Zero may require the consumer to provide proof that
the product is defective. For the avoidance of doubt, defective products or
parts become Sub-Zero’s property. Service will be provided during normal
business hours.
TERMS APPLICABLE TO EACH WARRANTY
The warranty applies only to products installed for normal residential use.
This warranty does not cover any parts or labor to correct any defect caused
by negligence, accident or improper use, maintenance, installation, service or
repair.
CLAIM PROCEDURE
In order to claim the Warranty, you must cease using the product when a fault
arises, contact Sub-Zero or authorized Sub-Zero
dealer where the product was purchased to report the issue and follow Sub-
Zero’s directions regarding what to do next. Sub Zero’s general contact
details are as follows:
Sub-Zero Group Australia
11-19 Bank Place
Melbourne VIC 3000
Phone: 03 9600 2218 Email:
serviceAU@subzero.com
**CLAIM PROCEDURE*
Except to the extent required by law, all consumer guarantees,
representations, warranties, terms and conditions in relation to the products
(whether implied or otherwise) are hereby excluded to the maximum extent
permitted by law.
To the fullest extent permitted by law, Sub-Zero excludes all liability for
damage or injury to any person, damage to any property and any indirect
consequential or other loss or damage.
Stainless steel (doors, panels, handles, product frames and interior surfaces) are covered by a limited 60-day parts and labor warranty for cosmetic defects.
Replacement water filters and air purification cartridges are not covered by the product warranty.
Full one year warranty applies to outdoor product. Product must be approved
for outdoor use, designated by model and serial number.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>