salicru SPS.HOME Uninterruptible Power Supply User Manual

salicru SPS.HOME Uninterruptible Power Supply

INTRODUCTION

THANK YOU LETTER
We thank you in advance for the trust placed in us in the pur-chasing of this product. Read this instruction manual carefully in order to familiarize yourself with its content, since the more you know and understand the equipment the greater your sat-isfaction, level of safety and optimization of its functionalities will be. We remain at your disposal for any additional information or queries that you may wish to make.

• The equipment described here is capable of causing significant physical damage in the event of incorrect connection and/or operation. For this reason its installa-tion, maintenance and/or repair must be carried out exclu-sively by our personnel or by qualified personnel.

• Although no effort has been spared to ensure that the in-formation in this user manual is complete and accurate, we are not responsible for any errors or omissions that may exist.
  The images included in this document are for illustrative purposes and may not represent exactly the parts of the equipment shown, therefore they are not contractual. How-ever, any divergence that may arise will be remedied or solved with the correct labelling on the unit.

• Following our policy of constant evolution, we reserve the right to modify the characteristics, operations or actions described in this document without prior notice.

• Reproduction, copying, assignment to third parties, modification or total or partial translation of this manual or document, in any form or by any means, without previous written authorization by our firm is prohib-ited, with the full and exclusive property rights over the same being reserved by our firm.

SAFETY INFORMATION

USING THIS MANUAL
The documentation of any standard equipment is available to the customer on our website for download: (www.salicru.com).

• For devices “powered by socket”, this is the website for obtaining the user manual and “Safety Instructions” EK266*08.
• For devices with “permanent connection” via terminals, a CD- ROM or pen drive containing all necessary information for connection and commissioning, including “Safety In-structions” EK266*08, may be supplied with it.

Before carrying out any action on the equipment relating to its installation or commissioning, change of location, configuration or manipulation of any kind, you must read the safety instruc-tions carefully.

The purpose of the user manual is to provide information re-garding safety and explanations of the procedures for installa-tion and operation of the equipment. Read them carefully and follow the steps indicated in the order established.

Compliance with the “Safety Instructions” is mandatory and the user is legally responsible for compliance and enforcement.

• ‘SPS HOME, SPS, device, unit or UPS’ – Uninterruptible power supply.
  Depending on the context of the phrase, it can refer either to the actual UPS itself or to the UPS and the batteries, regardless of whether it is all contained in the same en-closure.

• ‘Battery or accumulator’ – Element that stores the flow of electrons by electrochemical means.

• ‘TSS’ – Technical Service and Support.

• ‘Client, installer, operator or user’ – These are used interchangeably and by extension to refer to the installer and/or operator who will carry out the corresponding ac-tions, and the same person may be responsible for carrying out the respective actions when acting on behalf of, or in representation of, same.

QUALITY ASSURANCE AND STANDARDS.

STATEMENT BY THE MANAGEMENT.
Our goal is customer satisfaction, therefore this Management has decided to establish a Quality and Environment Policy, through the implementation of a Quality and Environmental Management System that will enable us to comply with the requirements demanded in the ISO 9001 and ISO 14001 and also by our Customers and Stakeholders. Likewise, the management of the company is committed to the development and improvement of the Quality and Environ-mental Management System, through:

• Communication to the entire company of the importance of satisfying both the client’s requirements as well as legal and regulatory requirements.
• The dissemination of the Quality and Environment Policy and the setting of the Quality and Environment objectives.
• Conducting reviews by the Management.
• Providing the necessary resources.

STANDARDS.
SPS HOME is designed, manufactured and sold in accordance with Quality Management StandardEN ISO 9001. The mark indicates conformity to the EEC Directives through the ap-plication of the following standards:

• 2014/35/EU. – Low voltage safety.
• 2014/30/EU. – Electromagnetic Compatibility (EMC).
• 2011/65/EU. – Restriction of the use of hazardous sub-stances in electrical and electronic equipment (RoHS).

According to the specifications of the harmonized standards. Reference standards:

• EN-IEC 62040-1. Uninterruptible power supplies (UPS). Part 1-1: General and safety requirements for UPS used in user access areas.
• EN-IEC 62040-2. Uninterruptible power supplies (UPS). Part 2: EMC requirements.

The manufacturer accepts no liability in the event of modification of or intervention on the device by the user.

WARNING: The SPS.HOME is a category C1 UPS. It is not appropriate to use this device with basic life support applications, where a failure of the former can render vital equipment out of service or significantly affect its safety or effectiveness. It is also not recom-mended in medical applications, commercial transport, nuclear installations, or other applications or loads, where a failure of the product can lead to personal or material damages. The EC declaration of conformity of the product is avail-able to the customer upon express request to our head-quarters.

PRESENTATION

VIEWS OF THE DEVICE

Fig. 1. Common views for all models.

KEY FOR THE VIEWS.

1. AC power cable with plug on end.
2. Input breaker.
3. AC output sockets with autonomy in case of mains failure. 4 AC output sockets with protection for peripherals.
4. Start and stop button, inverter ‘On-Off’.
5. Multifunctional LED light.
6. USB communication port.
7. RJ45 input socket, telephone line/ASDL/modem.
8. RJ45 output socket, telephone line/ASDL/modem.

NOMENCLATURE

DESCRIPTION
The SPS.HOME series Off-Line UPS is designed for total adapta-tion to single- user environments. With the attractive appearance of a power distribution unit, it features six output power sockets, four derived from an efficient UPS capable of providing varying degrees of backup depending on the connected load level at output and two auxiliary for the most commonly used peripherals (modems, telephone lines, etc.). All of the sockets are supplied with power surge protection. The main function of the UPS is to provide power, in the event of mains failure, to the devices connected to the output sockets through its internal battery for a limited time. Off-Line UPS systems perform this task of protection against mains failures by providing a similar voltage for a period of time.

Under normal conditions, the output of the UPS is the same as the input of the AC power mains. By means of a real-time detec-tion circuit, mains power outages can be quickly detected and the system switched to battery mode in less than 6 ms, ensuring that its loads remain powered with a modified sine wave.

The device’s communication and control functionalities are available through a USB port and monitoring and management software.

Fig. 2. Structural block diagram.

Main features

• Off-Line technology.

• Compatibility with APFC loads.
  The vast majority of power supplies for electronic devices are switched-mode (SMPS) and they are increasingly being equipped with active power factor correction (APFC) to minimise distortion caused to the electrical line. SPS HOME UPSs are compatible with all devices that incorporate these functionalities.

• USB interface with HID protocol.

• USB for software monitoring and closing files.

• Downloadable software for Windows, Linux and Mac.

• Auto-detection with 50 / 60 Hz input frequency.

• ColdStart function.

• Automatic restart after mains outage and end of backup.

• Overload protection through accessible breaker.

• Battery protection through internal fuse.

• Fixings for wall mounting.

INSTALLATION AND OPERATION

Read and respect the Safety Information, described in chapter 2 of this document. Failure to obey some of the instructions described in this manual can result in a serious or very serious accident to persons in direct contact or in the vicinity, as well as faults in the equipment and/or loads connected to it.

RECEPTION OF THE DEVICE

Reception, unpacking and contents

Reception

• Check that the information on the label affixed to the packaging matches that specified on the order. Re-move the packing unit and check the above information against that on the nameplate of the SPS.HOME.
  If there are any discrepancies, report them, quoting the references on the delivery note.

• Check that no mishaps have occurred during transpor-tation.

Unpacking

• The packaging consists of a full-colour cardboard box with two moulded pieces of expanded polystyrene (EPS) to protect the SPS.HOME from impacts.

Content

• Device.
• Quick guide.
• Warranty information.
• Particular terms and conditions of warranty.
• 1 USB cable.
• 1 telephone/ASDL/modem cable.
• After reception, it is advisable to store the device in its original packaging as a preventative measure if installation is not to be carried out immediately.
• When the packaging needs to be disposed of, it must be carried out in accordance with current laws.
  We advise keeping it for at least 1 year.

SITING AND CONSIDERATIONS

Siting

• Install the unit in a location which takes into considera-tion and complies with the Safety Instructions of document EK266*08.
• The UPS can be placed on a flat surface (on a table) or mounted on a wall using the system located on the base of the device.

Considerations

Battery charging

• Although the unit’s internal battery is charged at the factory, it may run down during transportation and/or storage, so it should be charged for a minimum of 8 hours to ensure a full charge before using the device with complete assurance. Although the device can operate correctly without charging the battery for the specified time, the risk of a prolonged mains outage during the first hours of operation and the UPS’s available backup time should be assessed.
• To recharge the battery, simply leave the unit plugged into an AC socket. The battery will charge irrespective of whether the SPS.HOME is switched on or off.

Power connected to the SPS.HOME

• Check that the loads connected to the power sockets do not exceed the power rating of the unit (see Section 7 of this document).
  If the rated capacities are exceeded, an overload condi-tion will occur. If mains power is present, the input breaker will trip and, in battery mode, the device’s inverter will be blocked. Either way, the end result will be an unwanted stoppage of the device and loads.

• For optimum performance, keep the load connected to the SPS below 80% of rated capacity.

CONNECTION AND COMMISSIONING

• All of the device’s connections, including those related to control, will be made with all of the switches in standby and without mains power present (UPS power supply line selector set to ‘Off’).
• It should never be forgotten that a UPS is a generator of electrical energy, so the user must take the necessary precautions against direct or indirect contact when it is part of the facility.

Procedure to follow.
Observe the following order of operation and instructions:

• Plug the PC, screen and sensitive devices into the unit’s output sockets 3. Plug the modem and other non-sensitive and low-consumption peripherals into the SPS.HOME’s output sockets 4. Do not plug laser printers, paper shredders or other high-consumption electrical devices or high current probes into output sockets 4 and especially not into output sockets 3 with backup. The power demand of any of these devices will overload the SPS and possibly damage the unit.
• Take power cable 1 and insert the plug into a properly connected AC socket with an earth connection. The socket that supplies power to the device must have a properly connected earth cable ( ). The SPS.HOME’s power socket will be protected by a fuse or circuit breaker limiter. This line must not power machines with large electrical demands such as air conditioning units, refrigerators, etc.). Avoid the use of extension cables, since the SPS itself could be considered as a PDU.
• Press start-stop button 5 to start the unit. Its surrounding LED will light up and the unit will emit a beep. It is possible to start the unit without the presence of mains power (Coldstart function) by pressing on start-stop button 5. This, however, is not recommended because if a mains failure extends beyond the available backup, it will be necessary to carry out a forced stop. In the event of a mains failure and the battery’s backup reaching its end, the device will be automatically blocked, leaving the loads unpowered.Similarly, when mains voltage returns, the device will start automatically.
• If an overload is detected, an audible alarm consisting of a long beep will sound. To correct it, it is necessary to switch the UPS off and disconnect the load that exceeds the rated power of output sockets 3 with backup. Wait 10 seconds. Check that the fuse or circuit breaker of the line that supplies the SPS is correct or set to ‘On’ and then restart the UPS by pressing button 5.
• To keep the battery fully charged, always leave the SPS plugged into a live AC power outlet.
• If the UPS is stored or put away for a prolonged period of time, protect it from dust, knocks, etc., and keep the battery fully charged. Recharge the battery according to the time set in Table 2 of the EK266*08 Safety Instructions document and in correlation with the ambient temperature to which the SPS.HOME is subject. That way, a longer battery life will be ensured.

Optical and audible indications

Flashing

| Slow modulated beep (every 30 sec)|

Normal

| Mains failure – The UPS supplies power to sockets 3.

Flashing

|

Rapid modulated beep

(every 2 sec.)

|

Normal

| Mains failure – The UPS supplies power to sockets 3. With low battery voltage (end of backup), the audible

alarm modulates every 2 sec

On / Flashing

| Rapid modulated beep

(every 0.5 sec) for moderate overload or continuous for excessive

|

Normal / Tripped

| Overload – Activated by excessive load connected to the device’s output sockets. Stop the UPS, disconnect the load.

Activate the breaker if necessary. Switch on

the UPS.

Optical and audible indications guide.

Modem/telephone line connection
Use the cable supplied for the telephone line to extend the line from the wall socket to RJ45 input connector 8 of the SPS. Connect the telephone, modem or fax to RJ45 output connector 9. This connection provides the connected device with protection from possible voltage peaks.

Communications connection.
Connect the communications cable supplied with the device to the UPS’s USB port and the other end to the computer. With the Power Master software installed on the PC, both the status of the UPS can be monitored and a shutdown/automatic start can be performed remotely.

Software

• Free Power Master software download.Power Master is a UPS monitoring software which provides a user-friendly interface for monitoring and control. It features an auto shutdown function for systems consisting of several PCs in case of power failure. The software enables users to monitor and control any UPS in the same LAN through an RS232 or USB communications port, regardless of how far away they are from each other.

• Installation procedure:

• Go to the web page:
  http://support.salicru.com

• Select the required operating system and follow the instructions described on the web page to download the software.

MAINTENANCE, WARRANTY AND SERVICE

TROUBLESHOOTING GUIDE.

• If the UPS is not working properly, before calling T.S.S., try to resolve the issue using the information in Tab. 2.

UPS backup time not as expected.

| Battery not charged.| Connect UPS to power socket and allow to charge for at least 8 hours.
Battery slightly damaged.| Contact distributor or seller and, failing that, T.S.S.

UPS does not start.

| The ‘On-Off’ button is designed to prevent damage when performing quick stop and run operations| With the device on, press button 5 to switch it off. After 10 seconds, press button 5 to switch it back on.
SPS not connected to an AC power socket.| Connect it to a 220..240 V 50/60 Hz socket.
Battery has reached the end.|

Contact distributor or seller and, failing that, T.S.S.

Mechanical problem.

The SPS’s output sockets do not supply voltage.

|

Breaker tripped by an overload

| If an overload is detected, an audible alarm consisting of a long beep will sound. To correct it, it is necessary to switch the UPS off and disconnect the load that exceeds the rated power of output sockets 3 with backup. Wait 10 seconds. Check that the fuse or circuit breaker of the line that supplies the SPS is correct or set to ‘On’ and then restart the UPS by pressing button 5.

Battery discharged.

| Connect the SPS to a power socket for at least 4 hours, preferably with no load connected to prevent a mains failure from discharging the battery and leaving the loads unpowered
Unit has been damaged by a repetition of voltage peaks.| Contact distributor or seller and, failing that, T.S.S.

Power Master is inactive

| Serial port/USB cable not connected| Connect serial port/USB cable between SPS and computer. Use cable supplied with unit.

SPS.HOME does not provide battery power.

| Switch on PC and UPS.

Wait 10 seconds and restart SPS.HOME. When

restarting unit, fault should be resolved.

Troubleshooting guide

MAINTENANCE

• This product does not require preventative maintenance.

WARRANTY CONDITIONS.

Terms of the warranty

On our website you will find the warranty conditions for the product you have purchased where you can also register it. It is recommended to do so as soon as possible to include it in the database of our Technical Service and Support (T.S.S.). Among other advantages, it will streamline any regulatory procedures for the intervention of T.S.S. in the event of a fault.

Exclusions.
Our company will not be bound by the warranty if it notices that the defect in the product does not exist or was caused by improper use, negligence, improper installation and/or verification, attempts at unauthorized repair or modification, or any other cause beyond the intended use, or by accident, fire, lightning or other hazards. Nor shall it cover any compensation for damages.

TECHNICAL SERVICES NETWORK.
Information about our national and international Technical Ser-vice and Support (T.S.S.) centres can be found on our website.

ANNEXES

TECHNICAL SPECIFICATIONS

discharge.
Overload in line mode.| > 110%, output voltage cut after 1 min; > 200%, output voltage cut immediately.
Overload in battery mode.| > 100 %, output voltage cut after 1 min; > 120 %, output voltage cut immediately.
Output sockets.| 6 (4 for powering critical loads – battery mode – and 2 direct from mains with protection against power surges).
Battery.|
Element rated voltage.| 12 V DC (Pb-Ca sealed, maintenance-free battery).
Number of elements / Capacity.| 1 / 5 Ah| 1 / 5.6 Ah
Typical recharge time.| 8 hours to 90% charge.
Optical and audible indication.|
Surrounding the On-Off button.| LED.
Indications.| Normal operation mode, mains failure, end of backup, overload.

Audible alarm.

| Battery mode: beep every 30 sec. Low battery: beep every 0.5 sec. Overload: continuous beep.

Failure: continuous beep.

Physical.|
Maximum dimensions (depth × width × height).| 316 (with power cable included 336) x 121 x 93 mm.
Weight.| 2.7 kg| 3.0 kg
Protection rating.| IP20
Total output sockets.| 6
Output sockets for critical loads + overvoltage protection.| 4
Output sockets with overvoltage protection.| 2
Environmental.|
Operating temperature.| 0.. 40ºC
Relative humidity.| 0.. 90% non-condensing.
Interface, communication and management.|
USB (HID).| Yes
Phone line/ADSL protector.| Yes
Power Master software.| Windows 8 / 7 / Vista / XP / 2000 / Server 2003, Linux.
Battery self-charging.| Yes
Auto start after mains failure.| Yes

address: Avda. de la Serra 100 08460 Palautordera BARCELONA
Tel. +34 93 848 24 00 services@salicru.com
SALICRU.COM

The Technical Service and Support (T.S.S.) network, Com-mercial network and warranty information are available in website: www.salicru.com

Product Range

• Uninterruptible Power Supplies (UPS) Lighting Flow Dimmer-Stabilisers DC Power Systems
• Static Inverters
• Photovoltaic Inverters
• Voltage stabilisers
• Variable frequency drives

@salicru_SA
www.linkedin.com/company/salicru

References

• Salicru - Multinacional dedicada a la Potencia Eléctrica | SAIs | UPS 
• Soporte Online 
• Salicru - Multinacional dedicada a la Potencia Eléctrica | SAIs | UPS 

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>