beamZ DMX-004DII 4 Channel Switch Pack Instruction Manual

: June 9, 2024
: beamZ

Table of Contents

beamZ DMX-004DII 4 Channel Switch Pack
INSTALLATION INSTRUCTION
UNPACKING INSTRUCTION
- POWER SUPPLY
DMX-512 CONNECTION
FUNCTION AND CONTROL PANEL
OPERATION
- AUTO MODE
DMX MODE
DMX CHANNELS
TECHNICAL SPECIFICATION
Documents / Resources

beamZ DMX-004DII 4 Channel Switch Pack

INSTALLATION INSTRUCTION

Congratulations to the purchase of this Beamz product. Please read this manual thoroughly prior to using the product in order to benefit fully from all features.
Read the manual prior to using the product.
Follow the instructions in order not to invalidate the warranty.
Take all precautions to avoid fire and/or electrical shock. Repairs must only be carried out by a qualified technician in order to avoid electrical shock.
Keep the manual for future reference.
Prior to using the product, please ask advice from a specialist. When the unit is switched on for the first time, some smell may occur. This is normal and will disappear after a while.
The unit contains voltage carrying parts. Therefore do NOT open the housing.
Do not place metal objects or pour liquids into the product. This may cause electrical shock and malfunction.
Do not place the product near heat sources such as radiators, etc. Do not place the unit on a vibrating surface. Do not cover the ventilation holes.
The product is not suitable for continuous use.
Be careful with the mains lead and do not damage it. A faulty or damaged mains lead can cause electrical shock and malfunction.
When unplugging the product from a mains outlet, always pull the plug, never the lead.
Do not plug or unplug the unit with wet hands.
If the plug and/or the mains lead are damaged, they need to be replaced by a qualified technician.
If the product is damaged to such an extent that internal parts are visible, do NOT plug the unit into a mains outlet and DO NOT switch the product on. Contact your dealer. Do NOT connect the product to a rheostat or dimmer.
To avoid fire and shock hazard, do not expose the product to rain and moisture.
All repairs should be carried out by a qualified technician only.
Connect the product to an earthed mains outlet (220-240Vac/50Hz) protected by a 10-16A fuse.
During a thunderstorm or if the product will not be used for a longer period of time, unplug it from the mains. The rule is: Unplug it from the mains when not in use.
If the product has not been used for a longer period of time, condensation may occur. Let the unit reach room temperature before you switch it on. Never use the product in humid rooms or outdoors.
During operation, the housing becomes very hot. Do not touch it during operation and immediately after.
To prevent accidents in companies, you must follow the applicable guide lines and follow the instructions.
Secure the product with an extra safety chain if the unit is ceiling mount. Use a truss system with clamps. Make sure nobody stands in the mounting area. Mount the effect at least 50cm away from inflammable material and leave at least 1 meter space on every side to ensure sufficient cooling.
This product contains high intensity LEDs. Do not look into the LED light to prevent damage to your eyes.
Do not repeatedly switch the product on and off. This shortens the life time.
Keep the unit out of the reach of children. Do not leave the unit unattended.
Do not use cleaning sprays to clean switches. The residues of these sprays cause deposits of dust and grease. In case of malfunction, always seek advice from a specialist.
Only operate the product with clean hands.
Do not force the controls.
If the product has fallen, always have it checked by a qualified technician before you switch the product on again.
Do not use chemicals to clean the unit. They damage the varnish. Only clean the product with a dry cloth.
Keep away from electronic equipment that may cause interference.
Only use original spares for repairs, otherwise serious damage and/or dangerous radiation may occur.
Switch the product off prior to unplugging it from the mains and/or other equipment. Unplug all leads and cables prior to moving the product.
Make sure that the main lead cannot be damaged when people walk on it. Check the mains lead before every use for damages and faults!
The mains voltage is 220-240Vac/50Hz. Check if the power outlet matches. If you travel, make sure that the main voltage of the country is suitable for this product.
Keep the original packing material so that you can transport the product in safe conditions
This mark attracts the attention of the user to high voltages that are present inside the housing and that are of sufficient magnitude to cause a shock hazard.
This mark attracts the attention of the user to important instructions that are contained in the manual and that he should read and adhere to.
DO NOT LOOK DIRECTLY INTO THE LENS. This can damage your eyes. Persons who are subject to epileptic attacks should be aware of the effects that this light effect may have on them.
The product has been certified CE. It is prohibited to make any changes to the product. They would invalidate the CE certificate and their guarantee!
NOTE: To make sure that the unit will function normally, it must be used in rooms with a temperature between 5°C/41°F and 35°C/95°F.
Electric products must not be put into household waste. Please bring them to a recycling center. Ask your local authorities or your dealer about the way to proceed.
The specifications are typical. The actual values can slightly change from one unit to the other. Specifications can be changed without prior notice. prior notice.
Do not attempt to make any repairs yourself. This would invalid your warranty. Do not make any changes to the product. This would also invalid your warranty. The warranty is not applicable in case of accidents or damages caused by inappropriate use or disrespect of the warnings contained in this manual. Beamz cannot be held responsible for personal injuries caused by a disrespect of the safety recommendations and warnings. This is also applicable to all damages in whatever form.

UNPACKING INSTRUCTION

CAUTION! Immediately upon receiving the product, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damage from shipping or the package itself shows signs of mishandling. Save the package and all packing materials. In the event that the product must be returned to the factory, it is important that the product be returned in the original factory box and packing.
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your device. Leave the device switched off until it has reached room temperature.

POWER SUPPLY

The label on the backside of the product is indicated on this type of power supply must be connected. Check that the mains voltage corresponds to this, all other voltages than specified, the light effect can be irreparably damaged. The product must also be directly connected to the mains and may be used. No dimmer or adjustable power supply.
Always connect the device to a protected circuit (circuit breaker or fuse). Make sure the device has an appropriate electrical ground to avoid the risk of electrocution or fire.

DMX-512 CONNECTION

If you are using a standard DMX controller, you can connect the DMX output of the controller directly to the DMX input of the first unit in a DMX chain. Always connect the output of one unit with the input of the next unit until all units are connected.
If you use a controller with 5 pin DMX connection you will need to use a 5-pin to 3-pin adapter.
At the last fixture, the DMX cable has to be terminated. Solder a 120 Ohm resistor between signal (-) and signal (+) into a 3-pin XLR connector and plug this into the DMX output of the last fixture in the chain.

FUNCTION AND CONTROL PANEL

beamZ-DMX-004DII-4-Channel-Switch-Pack-
fig-3

Output sockets
Green LED: Indicate the output of related channel
Display: Display all kinds of operating modes.
Up button: Select UP.
Down button: Select DOWN
Menu button: In automatic or DMX mode, select different functions
Mode button: Choose to work in automatic or DMX mode
Output fuse: Fuse for each channel (6.3A).
- Always replace with same type of fuse and always disconnect unit from main power before replacing the fuse.
Power switch
Power Wire
DMX output
DMX input

OPERATION

The unit has two operation modes, DMX or Auto mode.

AUTO MODE

The unit has 16 inner programmes. You can set the speed of the programmes.

Connect lights.
Press “MODE”, select P (programm)
Press “UP” or “DOWN”, select programm P1 – P16
Press “MENU”, select Sp (speed)
Press “UP” or “DOWN”, select speed SP01 – SP99, 01 for the 30sec step and 99 for the fastest 10 steps per second.

DMX MODE

The unit can set to 1 channel, 2 channel or 4 channel DMX.

Connect the unit to a DMX controller
Press “MODE”, select A (adress)
Press “UP’ or “DOWN” to select the DMX start-adress 001-512
Press “MENU”, select CH (channel)
Press “UP” or “DOWN”, to select 1, 2 or 4 CH DMX
- CH1 means all the units outputs receive the selected DMX value.
- CH2 means unit is in 2 channel mode. CH1 and CH2 are one DMX channel. CH3 and CH4 are second DMX channel.
- CH4 means unit is in 4 channel mode. All 4 outputs have there own DMX channel
DMX value of switching. 0 to 127 is Off, 128 to 255 is On.

DMX CHANNELS

Channel	Function	Value
1	Switch channel 1	0-255
2	Switch channel 2	0-255
3	Switch channel 3	0-255
4	Switch channel 4	0-255

TECHNICAL SPECIFICATION

Rated voltage : AC220AC220～240V 50/60Hz
Outputs: 4
DMX ChannelChannels: 4 Channels
Function: DMX
Dimensions per unit: 260 x 210 x 90mm
Weight (per unit): 2.3 kg
The specifications are typical. The actual values can slightly change from one unit to the other. Specifications can be changed without prior notice.
The products referred to in this manual conform to the European Community Directives to which they are subject:
European Union
United Kingdom
Tronios B.V., Bedrijvenpark Twente Noord 18, 7602KR Almelo, The Netherlands
Tronios Ltd., 130 Harley Street, London W1G 7JU, United Kingdom
2014/35/EU
S.I. 2016:1101
2014/30/EU
S.I. 2016:1091
2011/65/EC
S.I. 2012:3032
Specifications and design are subject to change without prior notice.
www.tronios.com
Copyright © 2022 by TRONIOS the Netherlands

Documents / Resources

| beamZ DMX-004DII 4 Channel Switch Pack [pdf] Instruction Manual
DMX-004DII 4 Channel Switch Pack, DMX-004DII, 4 Channel Switch Pack, Switch Pack, Pack
---|---