cell2 ID26 Mini Light Head Instruction Manual

ID26 Mini Light Head
Instruction Manual 170221M41-2

ID26 Mini Light Head

Surface Mount

NOTE: RED wire has priority over WHITE wire when both wires are activated.

Operation

This lightheaded is designed with 2 sets of memory to allow instant switch between 2 pre-set flash patterns with a simple switch of a button (user- supplied). Connect BLACK  wire to Ground, and apply +VDC to WHITE wire to activate Memory1 or to RED wire to activate Memory2.

Step 1

Select Function & Flash Pattern

a. Activate Memory1 by applying +VDC to WHITE wire.
b. While WHITE wire is activated, momentarily apply +VDC to YELLOW wire:
• once for <1 second for next flash pattern.
• quickly three times for reset to default.

Step 2

Select Mode

a. While WHITE wire is activated, apply +VDC to YELLOW wire for >3 seconds to enter Mode setting.
b. Once in Mode setting, lightheaded will display dim slow pulses based on its Mode and Group (single or double pulses respectively).
c. Momentarily apply +VDC to YELLOW wire for <1 second for next Mode. (refer to Mode charts).
d. Momentarily apply +VDC to YELLOW wire quickly 3 times within 1 second to reset to Mode1.
e. When desired mode is selected, apply +VDC to YELLOW for >3 seconds or disconnect all power to exit Mode setting.
f. To configure Memory2, apply +VDC to RED wire and repeat the above steps A & B.

NOTE:
For multiple lightheaded installation, heads in the same Group flash together. [G1] Heads alternate with [G2] Heads. For synchronization all YELLOW wires must be connected  together, and set at the same Flash Pattern.

All = Top & Bottom simultaneous
Split = Top & Bottom alternating
[G1] = Group1 [G2] = Group2

| Mode| Steady & Warning Effect
---|---|---
1| All (single pulse)| Top Steady & Bottom Double Flash [G1]
2| All (double pulse)| Top Steady & Bottom Double Flash [G2]
3| Split (single pulse)| Bottom Steady & Top Double Flash [G1]
4| Split (double pulse)| Bottom Steady & Top Double Flash [G2]
5| Top (single pulse)| Top Steady & Bottom Quad Flash [G1]
6| Top (double pulse)| Top Steady & Bottom Quad Flash [G2]
7| Bottom (single pulse)| Bottom Steady & Top Quad Flash [G1]
8| Bottom (double pulse)| Bottom Steady & Top Quad Flash [G2]
[G1] = Group1 [G2] = Group2
All = Top & Bottom simultaneous
Split = Top & Bottom alternating

| Mode| Full Steady Effect
---|---|---
1| All (single pulse)| All high power
2| All (double pulse)| All low power
3| Split (single pulse)| All high power
4| Split (double pulse)| All low power
5| Top (single pulse)| Top high power
6| Top (double pulse)| Top low power
7| Bottom (single pulse)| Bottom high power
8| Bottom (double pulse)| Bottom low power

All = Top & Bottom simultaneous
Split = Top & Bottom alternating

Examples

Example Configuration#1:
I would like Memory1 to be Full Steady (All low power), and Memory2 to be split Ultra flash (Top row LEDs alternate Bottom row LEDs).

1. Activate WHITE  wire and select FP#15.
2. Enter Mode setting and select Mode#2.
3. Activate RED wire and select FP#11.
4. Enter Mode setting and select Mode#3 (or Mode#4).

Example Configuration#2:
I would like Memory1 to be Top Steady & Bottom Double Flash, and Memory2 to be All Ultra flash.

1. Activate WHITE  wire and select FP#14.
2. Enter Mode setting and select Mode#1 (or Mode#2).
3.  Activate RED wire and select FP#11.
4.  Enter Mode setting and select Mode#1 (or Mode#2).

[G1] = Group1 [G2] = Group2

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>