TESmart HKS0802A1U KVM Switch 4 Computers 2 Monitors User Manual
- June 9, 2024
- TESmart
Table of Contents
4-Port Dual Monitor HDMI KVM Switch
ENJOY THE VIVID WORLD
HDMI•Dual
USER MANUAL
Features:
- Using only 1 set of keyboard, mouse and 2 monitors to control 2 computers
- Support Unix/Windows/Debian/Ubuntu/Fedora/Mac OS X/Raspbian/Ubuntu for Raspberry Pi and other Linux basic system
- Support resolution up to 3840.2160@60HZ
- Support hot plug, disconnect or connect devices to the KVM at any time without tuming off PC
- With EDID emulators in each input port, keep PCs always have correct information, prevent displays setting change while switching input ports
- Support front panel button, keyboard hotkeys, IR remote control and RS232 to control KVM
- Available to use keyboard and mouse without any delay after switching input sources
- With extra USB 2.0 port, it is possible to connect bar code scanner, USB hard device or other USB device
- Support keyboard and mouse pass through mode to improve KVM compatibility
- Support DCC I
Packing List
1 Dual Monitor HDMI KVM Switch
1 IR remote control
1 IR Receiver cable
1 DC 12V power adapter
1 3 Pins Connector(For RS232)
2 Rack-eras 1 AUX Cable
1 User manual
Panel Description:
ID | Name | Description |
---|---|---|
1 | DC 12V | DC 12V power supply |
2 | RS232 port | Connect this port to any control termination, then it is able |
to select the input sources by sending RS232 commands
3| Ext.IR| For extended IR receiver cable input
4| L/R audio output| Analog audio output, connect to speaker
5| Standard USB 2.0 port| Connect to USB 2.0 devices, printers, USB drives
6| DCCI port| Used for product cascading to realize simultaneous display of 4
monitors
7| Keyboard and mouse input| Connect to keyboard and mouse
8| HDMI output ports| Connect to HDMI displays
9| PC 4 Input| HDMI input A/B: Connect to the two outputs of the same computer
USB:Connect to computer by USB Type A to Type B cable
10| PC 3 Input| HDMI input A/B: Connect to the two outputs of the same
computer
USB:Connect to computer by USB Type A to Type B cable
11| PC 2 Input| HDMI input A/B: Connect to the two outputs of the same
computer
USB:Connect to computer by USB Type A to Type B cable
12| PC 1 Input| HDMI input A/B: Connect to the two outputs of the same
computer
USB:Connect to computer by USB Type A to Type B cable
13| Auto scan time interval settings| [MIN]: Press [MIN] to loop between 0-59
minutes
[SEC]: Press [SEC] to loop between 0-59 seconds
[Set]: After setting minutes and seconds, press button [Set] to enter final
scan time interval setting
14| LED display| Display current selected input port
15| Status LED| Red: Turn off auto scanning mode Green: Turn on auto scanning
mode
16| IR receiver| Receive IR remote signal
17| Keypad output A| [1-4]: Press button[1]—[4] to directly select input 1-4
[Output A]: Keyboard and mouse focus on the desktop of output A in the display
mode 2
[Output B]: Keyboard and mouse focus on the desktop of output B in the display
mode 2
[Output A]+[1-4]: After pressing [Output A], then press [1-4] to switch input
sources of
[Output B]+[1-4]: After pressing [Output B], then press [1-4] to switch input
sources of output B
[Close]: Press this button to turn on or off the LED display and monitor
[Scan]: Press this button to start or stop automatically scanning between
input1 to input8. The interval time can be set by [Set], [MIN], [SEC] as
described above
18| Power switch| Turn on or turn off power supply
Connection Diagram :
Stepl : Connect the two outputs of the PC1 to the Input A and Input B of the KVM PC1 inputs. Connect the USB of the PC to the USB of the KVM PC1 inputs with USB type A to B cable
Note: Both Input A and Input B
should be connected to the same computer. If connect only one of them, then
the dual monitor function would not work properly.
Step 2: Connect keyboard, mouse and monitors to the specified ports.
Step 3: Connect speakers, USB devices, Ext. IR and RS232 to the KVM.
Step 4: Directly connect the DCCI port of first KVM switch according to above steps, in order to realize simultaneous display of 4 monitors
Cascade Diagram
Note: The slave only connects to monitors and computers. Computers need
to connect 4 HDMI cables simultaneously.
Step 5: Turn on the power switch to start the Dual Monitor KVM.
How To Use :
- Set up the connection according to the connection diagram.
- After all the PCs are started in step 1, then you can control the Dual Monitor KVM by keyboard hot keys, IR control or the front-panel key, the specific control methods are as follows:
How to use keyboard hot keys :
Press [Alt] key twice to change active selected computer in display mode 2
Note: Display mode 2 means one monitor display one PC.
Select port by port number Turn off auto switching mode Enable or disable
buzzer sound Turn on auto switching mode Note: Default auto switching time
interval is 6 seconds, you are able to change this value by following hot key
commands:
Increase or decrease auto switching time interval Note:1 second per step,
the time is up to 250 seconds.
Turn on or off keyboard and mouse pass through mode Note: For the best
compatiblity, it is better to turn on keyboard and mouse pass through mode. In
this mode, the keyboard and mouse are dynamically mapped to computer, so you
are able to use special keyboard and mouse that with multimedia keys or other
customized keys.
How to identify whether the KVM is in keyboard and mouse pass through
mode?
Turn on the KVM, press [Scroll Lock] + [Scroll Lock] + [F3], if buzzer beeping
twice, the KVM is in keyboard and mouse pass through mode. And beeping once
means in keyboard and mouse emulation mode.
HOW TO CHANGE THE HOT KEYS COMBINATION:
There are two kinds of trigger hot keys in this product,the default is [Scroll
Lock] key, and the alternative is the [Right-Ctrl] key.if [Scroll Lock] key
has been used for other functions, you can switch the hot key to [Right-Ctrl]
by:
Method 1:
Press and keep holding the [Set] button on the front panel until you hear the
buzzer is beeping, then restart KVM.
Method 2:
Press [Scroll Lock]+[Scroll Lock]+[F1], and you will switch the control hot
key to [Right Ctrl]. Vice verse, press [Right Ctrl]+[Right Ctrl]+[F1J, and you
will switch the control hot key to [Scroll Lock].
IR Remote Control :
1 |
Switch to PC 1 |
---|---|
2 |
Switch to PC 2 |
3 |
Switch to PC 3 |
4 |
Switch to PC 4 |
M |
The function is the same as the function of the panel key Output A |
P |
The function is the same as the function of the panel key Output B |
Turn on auto switching mode |
Note:
- For the safety request by some express company, the remote control is not equipped battery by default. Please install the button battery CR2025 before using it.
- Unspecified buttons at above are non-functional.
RS232 Commands (HEX):
Commands | Content |
---|---|
AA BB 03 01 01 EE | Switch to PC 1 |
AA BB 03 01 02 EE | Switch to PC 2 |
AA BB 03 01 03 EE | Switch to PC 3 |
AA BB 03 01 04 EE | Switch to PC 4 |
AA BB 03 02 00 EE | Turn off buzzer |
AA BB 03 02 01 EE | Turn on buzzer |
AA BB 03 03 00 EE | Control output A to switch to previous input pod |
AA BB 03 03 01 EE | Control output A to switch to next input port |
AA BB 03 04 00 EE | Control output B to switch to previous input port |
AA BB 03 04 01 EE | Control output A to switch to next input port |
Commands | Content |
AA BB 03 05 01 EE | Change active selected computer in display mode 2 |
AA BB 03 06 00 EE | Turn on keyboard and mouse pass through mode |
AA BB 03 06 01 EE | Turn off keyboard and mouse pass through mode |
AA BB 03 07 01 EE | Switch the control hot key to [Right Ctrl] |
AA BB 03 07 00 EE | Switch the control hot key to [Scroll Lock] |
AA BB 03 08 01 EE | Turn on auto switching mode |
AA BB 03 08 00 EE | Turn off auto switching mode |
AA BB 04 09 mm ss EE | Set the auto switching time interval; mm means minutes |
(0x00-0x38) ss means seconds (0x00-0x38)
Note: the minimum time interval is 5s.
Warranty Information:
We warrant this product as free of defects in material and workmanship for a period of one (1) year from the date of shipment. If during the period of warranty this product proves defective under normal use, we will repair or replace this product, provided that this product has not been subjected to mechanical, electrical, or other abuse or modifications. If it fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair. Such repairs are warranted for six (6) months from the day of reshipment to the buyer.
Technical Support
Thank you for purchasing the TESmart HDMI KVM Switch.
We are here to help you! Do you need assistance setting up your product?
Please make sure you:
-Visit https://support.tesmart.com for knowledge base and troubleshooting or scan the QR code directly with apps like Twitter.
-Consult support@tesmart.com for technical support.
https://support.tesmart.com/hc/en-us
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>