Clarke MAXXI II Dry Vacuum User Manual
- June 9, 2024
- Clarke
Table of Contents
Clarke MAXXI II Dry Vacuum
How To Use
Handle adjusting
Before operation. Wet pick-up
Before operation. Dry pick-up
Hose handling
Switch on
Emptying MAXXI II – 35
Emptying by drainhose MAXXI II – 55/75
Emptying by spout MAXXI II – 55/75
Cartridge filter
Dust bag replacement
Sack filter/wet filter
Float
Cord handling
Storage
Important safety instructions
Symbols used to mark instructions
-
DANGER
The danger that leads directly to serious or irreversible injuries, or even death. -
WARNING
The danger can lead to serious injuries or even death. -
CAUTION
Danger can lead to minor injuries and damage. -
Before starting up your vacuum cleaner for the first time, this instruction manual must be read through carefully. Save the instructions for later use.
Instructions for use
Besides the operating instructions and the binding accident prevention
regulations valid in the country of use, observe recognised regulations for
safety and proper use.
Purpose and intended use
This vacuum cleaner is to be used for commercial or for household use.
Accidents due to misuse can only be prevented by those using the machine. READ
AND FOLLOW ALL SAFETY INSTRUCTIONS. This machine is suitable for picking up
dry, non-flammable dust and liquids.
Any other use is considered improper use. The manufacturer accepts no liability for any damage resulting from such use. The risk for such use is borne solely by the user. Proper use also includes proper operation, servicing, and repairs as specified by the manufacturer.
Important warnings
WARNING
- To reduce the risk of fire, electric shock, or injury, please read and follow all safety instructions and caution mar-kings before use. This vacuum cleaner is designed to be safe when used for cleaning functions as specified. Should damage occur to electrical or mechanical parts, the cleaner and/or accessory should be repaired by a competent service station or the manufacturer before use in order to avoid further damage to the machine or physical injury to the user.
- This machine is for indoor use only.
- Do not leave the machine when it is plugged in. Unplug from the socket when not in use and before maintenance.
- Do not use a damaged cord or plug. To unplug grasp the plug, not the cord. Do not handle the plug or cleaner with wet hands. Turn off all controls before unplugging.
- Do not pull or carry by cord, use the cord as a handle, close a door on the cord, or pull the cord around sharp edges or corners. Do not run cleaner over the cord. Keep the cord away from heated surfaces.
- Keep hair, loose clothing, fingers, and all parts of the body away from openings and moving parts. Do not put any objects into openings or use them with the opening blocked. Keep openings free of dust, lint, hair, and anything else that could reduce the flow of air.
- This machine is not suitable for picking up hazardous dust.
- Do not use to pick up flammable or combustible liquids such as gasoline, or use in areas where they may be present.
- Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
- This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understanding the hazards involved.
- Children shall be supervised to make sure that they do not play with the appliance.
- Cleaning and user maintenance shall not be made by chil-dren without supervision.
- Use extra care when cleaning on stairs.
- Do not use it unless filters are fitted.
- If the cleaner is not working properly or has been dropped, da ma ged left outdoors, or dropped into water, return it to a service center or dealer.
- If foam or liquid escapes from the machine, switch it off immediately.
Double-insulated appliances
CAUTION
- Use only as described in this manual and only with the manufacturer’s recommended attachments.
- BEFORE YOU PLUG IN YOUR CLEANER, check the rating plate at the cleaner to see if the rated voltage agrees within 10% of the voltage available.
- This appliance is provided with double insulation. Use only identical replacement parts. See instructions for servicing double-insulated appliances.
In a double-insulated appliance, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated appliance, nor should a mean for grounding be added to the appliance. Servicing a double-insulated appliance requires extreme care and knowledge of the system, and should be done only by qualified service personnel. Replacement parts for a double-insulated appliance must be identical to the parts they replace. A double-insulated appliance is marked with the words “DOUBLE INSULATION” or “DOUBLE INSULATED.” The symbol (square within a square) may also be used on the product. The machine is equipped with a specially designed cord which if damaged, must be replaced by a cord of the same type. This is available at authorized service centers and dealers and must be installed by trained personnel.
CAUTION
-
Wet cleaner shall always have the Cartridge Filter, Wet Filter, and Float System mounted in the machine during both WET AND DRY operations.
Please also notice that the fill factor at the container may vary using a sack filter during wet pick-up operations. -
Clean the water level limiting device regularly and examine it for signs of damage.
-
This machine shall be stored indoors only.
Control/Operation
Starting and operating the machine
Check that the electrical switch is switched off (in position 0). Check
that suitable filters are installed in the machine. Then connect the suction
hose to the suction inlet at the machine by pushing the hose forward until it
fits firmly in place at the inlet. Then connect the two tubes with the hose
handle, and twist the tubes in order to ensure that they are properly fitted.
Attach a suitable nozzle to the tube. Choose a nozzle depending on what type
of material is to be picked up. Connect the plug to a proper electrical
outlet. Put the electrical switch into position 1 in order to start the motor.
Some variants have two motors/fan units and two electrical switches – one
switch for each motor.
Before wet pick-up
CAUTION
The machine is equipped with a float system that shuts off the airflow
through the machine when the maximum liquid level is reached. Never pick up
liquid without the floating body in place. To control: Loosen the latch at the
front of the motor top. Then open the motor top. Check that the float basket
and float valve are mounted at the filter plate.
Remounting:
Put back the motor top to the container. Then tighten the latch so that the
motor top is properly secured. Always use a chemical defoamer when picking up
water containing foaming detergents. Use a defoamer recommended by the
detergent manufacturer. During wet suction of foam: On two-motor machines
always run the machine with only one motor on, in order to avoid extreme
foaming and ensure the fill factor of the container.
Wet pick up
The machine is equipped with a floating body that shuts off the airflow
through the machine when the maximum liquid level is reached. You will then
hear a noticeable change of sound from the motor and notice that the suction
power decreases. When this occurs, switch the machine off. Disconnect the
machine from the socket.
Emptying after wet pick-up
Before emptying the container, unplug the vacuum cleaner. Always empty and
clean the container and the float system after picking-up liquids. Never pick
up liquid without the float system and filter(s) installed in the machine.
Emptying: MAXXI II 35 l
Release the front latch by pulling the lower parts outwards so that the motor
top is released. Open the motor top and lift it off. Remove the float system
and filter(s) from the cleaner. Disconnect the hose from the inlet by pulling
out the hose. Empty by tilting the container backward and pouring the liquids
into a floor drain or similar. Wipe the float valve and float basket with a
damp cloth before the motor top is reinstalled in the container. Put back the
filter(s) and the motor top to the container. Secure the motor top with the
front latch.
Emptying: MAXXI II 55/75 l
Drain hose:
MAXXI II has a draining hose. Detach the drain hose from the bracket by
pulling the hose downwards from the cleaner. Place the drain hose end near a
floor drain and then remove the plug at the hose end. The natural pressure
will then drain the liquids from the container. Emptying from the container
spout: Take off the rubber cap at the back of the container. The drain hose
must be attached during emptying from the container. Grasp with one hand at
the handle at the lower part of the container and release the lock. To avoid
movement of the trolley – place one foot at the base part of the trolley. Then
tilt the container backward and pour the liquids into a floor drain or
similar. Open up the motor top and wipe the float valve and the floating
basket with a damp cloth. Close the motor top to the container. Secure the
front latch.
CAUTION
Be careful not to interfere with your hands, fingers, etc. with the tilting
mechanism during emptying the container.
Emptying after the dry pick-up
Remove the electrical plug from the socket before emptying it after dry
pick-up. Check the filters and dustbag regularly. Release the latch by pulling
them outwards so that the motor top is released. Open up the motor top from
the container.
Cartridge filter:
To clean the filter you can either shake, brush or wash it. Wait until it is
dry before you reuse it. Check the motor filter, and replace it if it is
clogged.
Dustbag:
check the bag to ensure the fill factor. Replace the dust bag if necessary.
Remove the old bag. The new bag is fitted by passing the cardboard piece with
the rubber membrane through the vacuum inlet. Make sure that the rubber
membrane is passing past the heightening at the vacuum inlet.
After emptying:
Close the motor top to the container. Secure with the front latch. Never pick
up dry material without a cartridge filter or sack filter and dustbag fitted
in the machine. The suction efficiency of the vacuum cleaner depends on the
size and quality of the filter and dust bag. Therefore – use only the Original
filter and dust bags.
Maintenance
Maintenance of the float system
Remove the electrical plug from the socket before performing main-tenance.
Always empty and clean the container and the float system after picking-up
liquids. Release the front latch by pulling it outwards so that the motor top
is released. Open up the motor top from the container. Then loosen the
floating basket by turning the basket to the left. Remove the complete float
system from the motor top. A filter is located in front of the motor inlet.
Check this motor filter. Replace with new filter if the filter is clogged.
Wipe the float valve and float basket with a damp cloth before the motor top
is reinstalled in the container. Then reinstall the float valve to the
floating basket. Make sure that the sealed surface of the float valve is
installed upwards in a direction toward the motor top. To mount the floating
basket – fit the arrow at the basket to the arrow. Then secure the floating
basket by turning it to the right.
Maintenance
Remove the plug from the socket before performing maintenance. Before using
the machine make sure that the frequency and voltage shown on the rating plate
correspond with the mains voltage. Specifications and details are subject to
change without prior notice. The accessories shown in the pictures may vary
from model to model.
Always keep the cleaner in a dry place. The cleaner is designed for continuous heavy work. Depending on the number of running hours – the dust filters should be renewed. Keep the container clean with a dry cloth, and a small amount of spray polish. For details of after-sales service contact your dealer.
After using the cleaner
After use
Remove the plug from the socket when the machine is not in use. Wind up the
cord starting from the machine. The power cord can be wound up around the
handle/hooks located on the motor top or at the container. Some variants have
special storage places for accessories.
Transport
- Before transporting the dirt tank, close all the locks.
- Eventually, take off the motor top/container from the trolley (MAXXI II 55/75).
- Do not tilt the cleaner if there is liquid in the dirt tank.
- Do not use a crane hook to lift the cleaner.
Storage
Store the appliance in a dry place, protected from frost.
Warranty
Our general conditions of business are applicable with regard to the guarantee.
Unauthorized modifications to the appliance, the use of incorrect brushes in addition to using the appliance in a way other than for the intended purpose exempt the manufacturer from any liability for the resulting damage.
Recycling the cleaner
Make the old cleaner unusable.
- Unplug the cleaner.
- Cut the power cord.
- Do not discard electrical appliances with household waste.
As specified in European Directive 2002/96/EC on old electrical and electronic appliances, used electrical goods must be collected separately and recycled ecologically.
Only applicable to the UK. Please read these essential instructions
This vacuum cleaner is designed, developed, and rigorously tested to
function efficiently and safely when properly maintained and used in ac-
cordance with the following instructions. These instructions have been
prepared with safety and efficiency paramount. The machine operator must be
trained by a suitably qualified instructor and must understand these
instructions for use, and be made aware of any relevant regulations and
legislation in force at the time of use.
CAUTION
This machine is not suitable for use in explosive or inflammable atmospheres
or where such atmospheres are likely to be produced by the presence of
volatile liquid or inflammable gas or vapour.
In no circumstances should the power supply cord be wrapped around fingers or
any part of the operator’s person. The electrical supply plug must not be
subjected to undue stress by pulling on the power supply cord. Your MACHINE
must only be connected to an electrical supply of the same voltage and
frequency as indicated on the rating plate. Ensure that the plug fitted to the
end of the power supply cord is suitable for your supply socket, if not refer
to the information contained in ‘Electrical Connections’, or consult a
qualified electrician. The electrical installation from which the supply is
drawn must be maintained to the current Institute of Electrical Engineers’
wiring regulations.
Only applicable to the UK. Regular servicing and inspection
Regular servicing and inspection of your machine must be carried out by
suitably qualified personnel in accordance with relevant legislation and
regulations. In particular, electrical tests for earth continuity, insulation
resistance, and condition of the flexible cord should be checked frequently.
In the event of any defect, the machine MUST be withdrawn from service,
completely checked, and repaired by an authorized service technician.
Only applicable to the UK. Electrical connections
CAUTION
DOUBLE-INSULATED MACHINES – IMPORTANT:
This 240 volts 50 Hz. the machine is fitted with a 13 amp. 3-pin molded plug.
The plug is fitted with a 13 amp. detachable fuse. The correct replacement for
the fuse is identified by marking or colour coding. Only fuses that are ASTA
approved to BS 1362 should be fitted. Never use the plug without the fuse
cover fitted. Replacement fuse covers are available at any electrical retail
outlet.
If the available socket outlet is not suitable for the plug supplied, the plug
must be cut off and an appropriate plug fitted. The plug thus cut off MUST BE
DESTROYED for safety reasons before being disposed of. Machines built for
other voltages and frequencies are not normally supplied with a fitted plug.
If it is necessary to fit a plug, the wires in this power supply cord are
colored in accordance with the following code:
Only applicable to the UK. Blue-neutral brown-live
TO CONNECT THE NEW PLUG:
If using a three-pin plug, do not make any connection to the terminal in the
plug which is marked with the letter ‘E’ or by the safety earth symbol or
coloured green or green & yellow. This machine is double-insulated and no
earth connection is necessary. The blue wire must be connected to the terminal
in the plug which is marked with the letter ‘N’ or is coloured black or blue.
The brown wire must be connected to the terminal in the plug which is marked
with the letter ‘L’ or is coloured red or brown. If the plug to be fitted does
not conform to the above notation then consult a qualified electrician.
Specifications
| MAXXI II 35| MAXXI II 55/75
1 motor
| MAXXI II 55/75
2 motor
| MAXXI II 35| MAXXI II 55/75
1 motor
| MAXXI II 55/75
2 motor
| MAXXI II 35| MAXXI II 55/75
1 motor
---|---|---|---|---|---|---|---|---
Possible voltage, V| 220-240V| 220-240V| 220-240V| 120V| 120V| 120V| 100V|
100V
Power Piec| W| 1250| 1250| 2400| 1100| 1100| 2000| 1250| 1200
Protection grade (moist, dust)| |
IP24
|
IP24
|
IP24
|
IP24
|
IP24
|
IP24
|
IP24
|
IP24
Protection class (electrical)| | II| II| II| II| II| II| II| II
Airflow| liters/sec| 48| 48| 72| 45| 40| 64| 48| 42
Vacuum| kPa| 20| 20| 21| 20| 18| 19| 20| 18
Suction power| W| 250| 250| 390| 220| 170| 340| 250| 200
Sound pressure IEC 704| dB(A)+/-2| 81| 82| 84| 81| 82| 84| 81| 82
Sound pressure BS 5415| dB(A)+/-2| 62| 64| 66| 62| 64| 66| 62| 64
Vibration ISO 5349| m/s²| <1,5 +/- 1| <1,5 +/- 1| <1,5 +/- 1| <1,5 +/- 1| <1,5
+/- 1| <1,5 +/- 1| <1,5 +/- 1| <1,5 +/- 1
Tank capacity| liters| 35| 55/75| 55/75| 35| 55/75| 55/75| 35| 55/75
Weight| kg| 12,5| 24,5/27| 25,5/28| 12,5| 24,5/27| 25,5/28| 12,5| 24,5/27
Specifications and details are subject to change without prior notice.
14600 21st Avenue North
Plymouth, MN 55447-3408
www.clarkeus.com
Phone: 800-253-0367
Fax: 800-825-2753
©2013 Nilfi sk-Advance, Inc.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>