Clarke arke DL1122 CMSTRT Mechanics Seat Instruction Manual

rake DL1122 CMSTRT Mechanics Seat
Instruction Manual

MECHANICS SEAT
MODEL NO: CMSTRT
PART NO: 7630143
USER INSTRUCTIONS

INTRODUCTION

Thank you for purchasing this CLARKE Mechanics Seat.
Before attempting to use the product, it is essential that you read this manual thoroughly and carefully follow all instructions given. In doing so you will ensure the safety of yourself and that of others around you, and you can also look  forward to the product giving you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt as proof of purchase. This guarantee is invalid if the product is found to have been abused or  tampered with in any way, or not used for its intended purpose. Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission. This guarantee does not effect your statutory rights.

SAFETY PRECAUTIONS

1. Use your mobile seat for any task where you would normally sit or kneel. Place on level ground ensuring that the floor surface is hard enough that the castors do not sink in.
2. Use the seat as intended and in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the stool for operations different from those intended could result in a hazardous situation.
3. This product is not a toy. DO NOT allow children to play with or near this item and store out the reach of children.
4. Store idle equipment. When not in use this product must be stored in a dry location to inhibit rust.
5. DO NOT leave the mobile seat where it may accidentally become a trip hazard.
6. Inspect before every use; DO NOT use if parts are lose or damaged.
7. Have any damaged parts repaired or replaced immediately. Use genuine CLARKE parts only. The use of unauthorized parts may be dangerous and will invalidate the guarantee.
8. NEVER climb on, stand on, or attempt to ride on the mobile seat or use it to transport heavy objects.
9. DO NOT exceed the safe working load of the seat (136kg/300lbs).
10. NOTE: Be aware of dynamic loading!. Sudden shifts in the load may briefly create excess load, which may result in product failure.
11. It is recommended not to use the seat as a kneel board if you have any medical conditions with your legs or knees.
12. WARNING: DO NOT stand on this product. Serious injury can occur.
13. The warnings, cautions and instructions discussed in this instruction manual can’t cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which  cannot be built into this product and must be supplied by the operator.

UNPACKING & ASSEMBLY

Unpack and lay out all components, checking for any damage which may have occurred during transit, and ensuring that all parts are accounted for by checking against the parts list. Should there be any deficiency or damage, please contact your CLARKE dealer immediately.

PARTS LIST

ASSEMBLY

ASSEMBLY PRECAUTIONS

• Assemble only according to these instructions. Improper assembly can create hazards.
• Keep children, pets and bystanders out of the area during assembly. Distractions can cause you to lose control of tools, injuring yourself or others.
• Weight capacity and other product capabilities apply to correctly and completely assembled product only. DO NOT use if incomplete or incorrectly assembled.
• Assemble on a soft surface to avoid scratching or damaging the seat.

1.  Install the left (7) and right (8) brackets on the base plate (6) in turn, as shown. Lock them with the hex head cap screws (4) and M6 locknuts (5).

2. Install the seat chassis (2) on to the brackets (7 & 8). Lock the chassis in place using the socket head cap screws (4) and M6 locknuts (5)

3. Install the 4 castors (9) on the underside of the base plate (6), paying attention to the square clamp at the bottom of the castor thread and square hole on the base plate. Lock the castors in place using the M8 gasket (11), spring washer (12) and cap nut (10).

4. Install the tool rack (3) on the side of the brackets (7 & 8) as shown. Lock the rack in place using the cap screws (4) and M6 locknuts (5).  

5. Place the seat (1) onto the top of the chassis (2), making sure the 4 pins in the chassis line up with the 4 indents in the underside of the seat.
   • Seat is removable and can be used as kneel board.

6. Check that all nuts are tight and secure before using this seat. Your mobile seat is now ready for use.

SPECIFICATIONS

OTHER PRODUCTS IN THE CLARKE RANGE

• Ideal for Hobby, DIY, Semi Professional or Professional
• Part No.: See CLARKE Website| • Spray Guns, Airlines, DIY Tools, Professional Garage Tools
• Part No.: See CLARKE Website| •Ideal for use in the Garage or Workshop
• Part No.: See CLARKE Website
Tool Boxes & Cabinets – Multiple| Vehicle Jacks – Multiple| Battery Chargers & Jump starters – Multiple
---|---|---
| | ****
• From Portable Tool Boxes to Modular Garage Storage Systems
• Part No.: See CLARKE Website| • Suitable to lift 2 Tone to 20 Tone
• Bottle Jacks, Trolley Jacks, Farm Jacks
• Part No.: See CLARKE Website| • From Small Micro Jump starters to Heavy Duty Professional Starters
• Part No.: See CLARKE Website

VISIT: WWW.CLARKEINTERNATIONAL.COM FOR MORE INFORMATION

PARTS & SERVICE: 0208 988 7400
Parts Enquiries Parts@clarkeinternational.com
Servicing & Technical Enquiries
Service@clarkeinternational.com
SALES: UK 01992 565333 or Export 00 44 (0)1992 565335
INTERNATIONAL Hymnal Street, Epping, Essex CM16 4LG
www.clarkeinternational.com
Parts & Service: 020 8988 7400 /
E-mail: Parts@clarkeinternational.com
or Service@clarkeinternational.com

References

• Home - Clarke International

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>