Cell2 12VDC Silverblade Lighthead END Linear User Manual

: June 9, 2024
: Cell2

Table of Contents

Cell2 12VDC Silverblade Lighthead END Linear
- WIRING & FUNCTIONS
- LIGHTBAR WIRING
POWER CABLE
CAN CABLE
FUNCTION WIRES (Input)
FUNCTION WIRES (Output)
AUTO-DIMMING LIGHT SENSOR
PC PROGRAMMING
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Cell2 12VDC Silverblade Lighthead END Linear

Cell2 12VDC Silverblade Lighthead END Linear product

WIRING & FUNCTIONS

(CE – Single / Dual / Tri Colour – ECE R65/R10)
Proper installation of the product requires the installer to have a good understanding of automotive electronics, systems and procedures. Different applications may require different functions. For optimum efficiency, it is highly recommended to determine, configure and test the required functions prior to installation.

LIGHTBAR WIRING

NOTE: All function wires (Input) are activated by applying +VDC continuously.
[Px] = Order of Precedence. When more than one wire are activated at the same time, the wire with the higher precedence will override / affect the performance of the lower precedence wire. P1 being the highest order.
*Actual approval is based on the configuration of the model ordered.
WARNING

DO NOT USE THE POWER WIRE(S) AS THE LIGHTBAR ACTIVATION SWITCH. USE ONLY THE FUNCTION WIRE(S) TO SWITCH AND ACTIVATE.
ENSURE THE POWER WIRE(S) ARE PROPERLY CONNECTED BEFORE ACTIVATING ANY FUNCTION WIRE(S).
FAULTY CONNECTIONS MAY CAUSE THE LIGHTBAR TO MALFUNCTION AND / OR RESET TO ITS DEFAULT SETTINGS.
DO NOT USE A HIGH PRESSURE POWER WASHER TO CLEAN YOUR LIGHTBAR; THIS MAY DAMAGE YOUR LIGHTBAR AND VOID ITS WARRANTY.

POWER CABLE

Route power cables to the vehicle firewall towards the battery, preferably using a factory pass-through.
If drilling a hole is required, please ensure there are no factory components in the area to be drilled.
Splice 2 RED wires to form a single wire then install a fuse (user-supplied) to the end of the RED wire, before connecting it to the battery. (for correct fuse rating, refer to the Lightbar Specs.)
Splice 2 BLACK wires to form a single wire then connect the BLACK wire to the vehicle chassis-ground next to the battery.
NOTE: Ensure that all wires of the power cable are firmly connected to the power source.

CAN CABLE

Route CAN Cable towards the CAN Controller Module.
Connect 2 CAN signal and Shield wires to respective counterparts on the 6-pin connector harness of the CAN Controller Module. (Refer to CAN Controller Module Installation and Operation Manual)

FUNCTION WIRES (Input)

Connect each individual function wire according to its function.
ECE R65 WARNING MODE
Activate ECE R65 Warning Mode by applying +VDC to GREEN-WHT wire.
All corner lightheads will display Double Flash [2Hz] simultaneously.
WARNING MODE 1
Activate Warning Mode 1 by applying +VDC to ORANGE-WHT wire. All warning lightheads will display Double Flash [2Hz] simultaneously.
WARNING MODE 2
Activate Warning Mode 2 by applying +VDC to YELLOW-WHT wire. All warning lightheads will display Double Flash [2Hz], left half alternating right half.
CRUISE MODE
Activate Cruise Mode by applying +VDC to RED-WHT wire. All warning lightheads will be activated in low power steady-burn.
FULL FRONT FLOOD
Activate Full Front Flood by applying +VDC to the YELLOW wire. All Front, Take-Down and Alley Lights will display in High Power steady-burn.
Note: If the lightbar is equipped with Dual or Tri Colour warning lighthead, Colour 2 or Colour 3 will be displayed respectively.
TAKE-DOWN LIGHT
Activate steady-burn Take-Down Light by applying +VDC to PURPLE wire.
When Take-Down Light is activate with Flashing Take-Down & Alley Light, Take- Down Light(s) will steady-burn while Alley Light(s) flash continuously.
ALLEY LIGHT
Activate steady-burn Alley Light by applying +VDC to

GREEN wire for Left-Side Alley Light.
BLUE wire for Right-Side Alley Light.

When Alley Light is activate with Flashing Take-Down & Alley Light, Alley Light(s) will steady-burn while Take-Down Light(s) flash continuously.
FLASHING TAKE-DOWN LIGHT & ALLEY LIGHT
Activate Flashing Take-Down & Alley Light (Left alternating Right) by applying +VDC to GREY wire.
TRAFFIC ARROW
Activate rear Traffic Arrow function by applying +VDC to:

WHITE wire for Left Arrow.
WHITE-BLK wire for Right Arrow.
Above 2 wires together for Centre-Out Arrow.

Note: If the lightbar is equipped with Dual or Tri Colour warning lighthead, Colour 2 or Colour 3 will be displayed respectively.
REAR WIG-WAG
Activate Rear Wig-Wag by applying +VDC to GREY-WHT wire. Rear lightheads will display Single Flash [2Hz], alternating side-by-side.
Note: If the lightbar is equipped with Dual or Tri Colour warning lighthead, Colour 2 or Colour 3 will be displayed respectively.
WARNING CUT-OFF
Deactivate warning lightheads in each respective area by applying

+VDC to PURPLE-WHT wire for Front Cut-off.
+VDC to BLUE-WHT wire for Rear Cut-off.
+VDC to ORANGE wire for Corner Cut-off.

Note: Warning Cut-off does not affect Take-Down Light, Alley Light and Traffic Arrow function.
LOW POWER OPERATION / DIM FUNCTION
Activate Low Power Operation by continuously applying +VDC to RED wire.

FUNCTION WIRES (Output)

Connect each individual function wires according to its function.
CONTROL PANEL SIGNAL INDICATOR (REAR LIGHTHEAD)
Connect BROWN-WHT wire to the display signal input of a compatible Control Panel to display current rear lighthead activity.
WARNING MODE SIGNAL
Connect BROWN wire to an apparatus that is needed to be turned ON with Warning Modes (e.g. Unlocking Siren Interlock); a 250mA signal is output whenever GREEN-WHT, YELLOW-WHT and/or ORANGE-WHT wire is activated.

AUTO-DIMMING LIGHT SENSOR

If the lightbar is equipped with an Auto-Dimming Light Sensor, Low Power Operation will automatically activate when the ambient brightness is below the set-value (e.g. night time) and deactivate once prior condition is removed. The Auto-Dimming Light Sensor takes precedence over all other function wires.