VIVO V2202 V25 Smartphone User Guide
- June 9, 2024
- Vivo
Table of Contents
VIVO V2202 V25 Smartphone User Guide
Introduction
Welcome to vivo
This Quick Start Guide tells you how to set up your phone and use its key
features.
For more detailed instructions, turn on your phone, then go to Settings >
About phone > Customer service > Manual.
You can also learn more useful information on vivo’s official website.
For legal information, go to Settings > About phone > Legal information.
For the FCC ID of this phone, please go to Settings > About phone > Status.
The features and images shown in this guide are for reference only.
They may differ from the actual product.
It is recommended to charge the device for at least 30 minutes before turning
it on for the first time.
Optimum operating temperature is 0°C to 35t and optimum storage temperature is
-20°C to 45°C.
Extreme heat or cold may damage your device or accessories.
The device IMEI can be obtained by dialing ‘#06#.
Power button
When the phone is off, press and hold the Power button to turn it on.
Press and hold the button when the phone is on to turn the phone off or
restart it.
Tips Insert/remove your SIM card using the provided eject tool.
To avoid damaging the device, do NOT remove the back cover.
This phone supports standard nano SIM / micro SD cards.
If necessary, please go to your local operator shop for a standard nano SIM
card.
Electrical Specification
Adapter| Input| 100-240V~
50/60Hz
1.1A
---|---|---
Output| 5.0V 2.0/9.0V 2.0A/
11.0V 4.0A
Mobile phone| 3.89v
Product Standard Accessories
- Cell phone x 1
- Charger x 1
- USB cable x 1
- Phone case x 1
- Earphone jack adapter x 1
- Eject tool x 1
- Warranty card x 1
- Quick start guide x 1
- Headset x 1
IFT
Operation of this equipment is subject to the following two conditions:
(1) it is possible that this equipment or device may not cause harmful
interference and (2) this equipment or device must accept any interference,
including interference that may cause undesired operation
FCC SAR
- Head: 0.87 W/kg
- Body-worn: 0.96 W/kg ( 15mm distance )
- Hotspot: 0.79 W/kg ( 10mm distance )
FCC statement
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
Caution: Changes or modifications not expressly approved by the vivo
Mobile Communication Co., Ltd. could void the user’s authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions. may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
SAR statement
This device meets the government’s requirements for exposure to radio waves.
This device is designed and manufactured not to exceed the emission limits for
exposure to radio frequency (RF) energy set by the Federal Communications
Commission of the U.S. Government.
The SAR limit set by the FCC is 1.6W/kg.
For body-worn operation, this device has been tested and meets the FCC RF
exposure guidelines for use with an accessory that contains no metal and
positions the device a minimum of 15mm from the body.
RF exposure compliance with any body-worn accessory that contains metal was
not tested and certified, and use of such body-worn accessory should be
avoided.
Accessory available in market and must be used to keep use distance 15mm from
EUT to body-worn operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>